Flight Control - Revell Control BLUESHOT Mode D'emploi

5 start prEparation
The model must be switched on first in order to connect it to the remote control. To
do this, connect the battery plug (1B) with the battery connection cable (1F). Do not
use force and ensure the correct polarity (5A). Then switch the ON/OFF switch on the
model (1G) to ON.
Before switching on the remote control, the control for thrust and rotation (2C) must
point down and the turbo switch (2G) must be set to 30% (5B). To switch on the
remote control, move the ON/OFF switch (2L) to ON. After approx. 3 seconds, the
model activates and is ready for use.
Once you have finished flying, switch the model off first and then the remote control.
6 trim adJustmEnt oF thE control
The correct trim is a basic requirement for fault-free flying behavior of the model. Its
adjustment is simple, but it requires some patience and a feel for it. Please observe
the following instructions precisely: Carefully move the thrust control up and raise the
helicopter approximately 0.5 to 1 metre in altitude.
6A If the model automatically moves slowly or quickly to the left or right ...
gradually press the trim for sideways flight (2K) in the opposite direction.
6B If the model moves by itself slowly or quickly around its own axis ...
press the trim adjustment for rotation (2A) incrementally in the opposite direction.
6C If the model automatically moves slowly or quickly forwards or
backwards ...
gradually press the forwards/backwards trim (2J) in the opposite direction.

7 Flight control

Note: Only minimal corrections of the controls are necessary for a smooth flying
behavior of the model! The direction indication applies when the model is viewed from
behind. If the model is flying forwards towards the pilot, it must be moved in the oppo-
site direction.
7A Take off or increase altitude by carefully moving the control for thrust and
rotation (2C) forward.
7B Land or decrease altitude by moving the control for thrust and
rotation (2C) backward.
7C Fly forward by moving the controller for forward/backward and sideways
flight (2I) carefully forward.
7D Fly backward by moving the controller for forward/backward and sideways
flight (2I) carefully backward.
7E Fly to the left by moving the controller for forward/backward and sideways
flight (2I) carefully to the left.
7F Fly to the right by moving the controller for forward/backward and sideways
flight (2I) carefully to the right.
7G Turn the model around to the left by moving the control for thrust and rotation (2C) to the
left.
7H Turn model around to the right by moving the control for thrust and rotation (2C) to
the right.
18
2D Video button: Press the video button to start the video recording. Press it again to
stop the recording. Only recordings that are stopped with this button are saved.
2G Turbo switch: Move the turbo switch to 60% to fly faster. In the 90% position, the
model carries out a flip when the control for forwards/backwards and sideways (2I)
movement is fully pressed. Only activate this mode if there is enough space available
and the model is flying at a height of at least 2 meters.
2H Flip button: Each time the Flip button is pressed, the model carries out a flip
maneuver. Only activate this function if there is enough space available and the model
is flying at a height of at least 2 meters.
8 mEmorY card
8A Insert a memory card: To record videos, the micro-SD memory card must be
inserted. The card must be inserted carefully in the slot on the rear side of the camera
(1H) with the contacts facing to the front and back until it engages. Do not use force,
otherwise the camera or the memory card could be damaged. Only standard micro-SD
memory cards can be used, HC cards are not supported.
8B Remove the memory card: To remove the micro-SD memory from the camera,
press on the memory card. There is an audible, quiet click and the card is pushed out
half way. It can then be pulled out completely using fingers.
8C Read the memory card: The micro-SD memory card can be read on a computer
using the USB adapter provided. To do this, insert the USB adapter in a free USB port
and insert the micro-SD card in the adapter with the contacts facing forwards. Note
that the card only fits into the adapter in one direction,
do not use force. If the card and the adapter are inserted correctly, the computer will
show a message.
instructions For saFE FlYing
GENERAL FLyING TIPS:
• Always place the model on a level surface.
An inclined surface can, under certain
circumstances, have a negative impact on
the starting behavior of the model.
• Always operate the controls slowly and
with a gentle touch.
• Always maintain visual contact with the
model and do not look at the remote
control!
• Move the thrust control down again some-
what as soon as the model lifts off from
the ground. Maintain flying altitude by
adjusting the thrust controller.
• If the model lowers, move the thrust
control slightly upward again.
• If the model climbs, move the thrust
control down slightly.
• To fly along a curve, tapping the direc-
tional controller very slightly in the
respective direction often suffices.
There is a general tendency during
preliminary attempts at flight to operate
the model's controls too aggressively.
Always operate the controls slowly and
carefully. Never fast and fitfully.
• Beginners should first master trimming
before attempting to master the thrust
controller. The model does not necessar-
ily have to fly straight at the beginning
- initially, it is more important to
maintain a constant height of approxi-
mately one meter above the ground by
repeatedly tapping the thrust control.
Only then should the pilot practice
steering the model left and right.
19