Installation; General; Hbg Models; Hbgb Models - Hatco HBG Série Manuel D'installation Et D'utilisation

English

General

Use the following procedures to install the HBG and HBGB
units.
WARNING
ELECTRIC SHOCK HAZARD: Unit is not weatherproof.
Locate unit indoors where the ambient air temperature is
a minimum of 70°F (21°C).
FIRE HAZARD: Locate unit a minimum of 1" (25 mm) from
combustible walls and materials. If safe distances are not
maintained, combustion or discoloration could occur.
CAUTION
Locate unit at the proper counter height in an area that is
convenient for use. The location should be level to prevent
the unit or its contents from falling accidentally and strong
enough to support the weight of the unit and contents.
The National Sanitation Foundation (NSF) requires that
units over 36" (914 mm) in width or weighing more than
80 lbs. (36 kg) either be sealed to or raised above the
installation surface. If this unit cannot be sealed at the
point of use, 102 mm (4") legs are included to allow for
proper cleaning access below the unit.
NOTICE
Do not turn on unit until it has been cleaned thoroughly.
Ceramic glass surface must be clear of debris to prevent
burn-on.
Do not lay unit on the side with the control panel or damage
to the unit could occur.

HBG Models

1. Remove unit from box.
NOTE: To prevent delay in obtaining warranty coverage,
complete online warranty registration. See the
IMPORTANT OWNER INFORMATION section for
details.
2. Remove tape and protective packaging from all surfaces
of unit.
NOTE: If 4" (102 mm) legs are required, refer to the OPTIONS
AND ACCESSORIES section in this manual for
installation instructions. 4" (102 mm) legs are included
with models greater than 36" (1041 mm) in width.
3. Place the unit in the desired location.
• Locate the unit in an area where the ambient air
temperature is constant and a minimum of 70°F
(21°C). Avoid areas that may be subject to active air
movements or currents (i.e., near exhaust fans/hoods,
air conditioning ducts, and exterior doors).
• Make sure the unit is at the proper counter height in an
area convenient for use.
• Make sure the countertop is level and strong enough to
support the weight of the unit and food product.
• Make sure all the feet on the bottom of the unit are
positioned securely on the countertop.
4. Install any accessories that came with the unit. Refer to the
OPTIONS AND ACCESSORIES section for details.
Form No. HBGM-0120

HBGB Models

Do not operate built-in models without the control box
mounted properly as described in the installation instructions.
Unit is designed and recommended for use in or on metallic
countertops. Damage to any countertop material caused
by heat generated from Hatco equipment is not covered
under the Hatco warranty. Verify with the manufacturer that
the material is suitable for prolonged temperatures up to
200°F (93°C).
Do not turn on unit until it has been cleaned thoroughly.
Ceramic glass surface must be clear of debris to prevent
burn-on.
1. Remove unit from box.
NOTE: To prevent delay in obtaining warranty coverage, complete
online warranty registration. See the IMPORTANT
OWNER INFORMATION section for details.
2. Remove tape and protective packaging from all surfaces
of unit.
3. Prepare the countertop opening. Refer to the "HBGB
Countertop Cutout Chart" in this section for recommended
countertop cutout dimensions.
4. Apply a bead of NSF-approved sealant on the top edge
of the countertop cutout and the underside of the trim
mounting ring. The sealant must be rated for use at a
minimum temperature of 250°F (121°C).
5. Place the unit into the countertop opening.
6. Remove any excess sealant.
7. Locate the remote-mounted control box assembly in an area
that is convenient for operation. If desired or necessary, the
control box can be mounted in a semi-remote location.
• The control box can be panel, surface, or under counter
mounted. If recess mounting, the control box will require
a mounting cutout of 7-1/4" W x 3-1/4" H (184 x 83 mm).
• The distance the control box can be mounted from the
unit is determined by the 3' (914 mm) conduit (optional
conduit lengths of 6' [1829 mm] and 10' [3048 mm] are
also available). Do not pull the conduit tight to increase
the mounting distance. The conduit should have some
slack after the control box is mounted.
Panel
3-1/4"
(83 mm)
Control Box Mounting Options
7

INSTALLATION

CAUTION
NOTICE
Under Counter
Surface
7-1/4"
(184 mm)
7"
(178 mm)
3"
(76 mm)
continued...