Preparing For Commissioning; Commissioning; Dust/Chip Exhaustion - ATIKA KGSZ 305 N Notice Originale

Pos. Order-no. Designation
22 Star grip
23 366011 Dust bag
24 Exhaust neck
25 Incline angle locking knob
25A Anti-swivel device
26 Scale for incline angle
27 Indicator for incline angle
28 Set screw for 90° saw head incline
29 Locking nut for set screw (90°)
30 Set screw for 45° saw head position
31 Locking nut for set screw (45°)
32 Set screw for the saw blade position
33 Locking nut for set screw (saw blade
position)
34 366020 Hexagonal screw for saw blade mounting

35 366018
Front saw blade flange 
36 366017
Saw blade (Ø 305 x 30 x 2.8 x 60T) 
37 366016
Rear saw blade flange
38 Saw blade locking device
39 Montage-holes
40 Anti-tip device
41 Adjusting screw for 45° incline (RH)
42 Locking nut for adjusting screw (45° RH)
43
Carbon brush 
44 Installation wrench
45 366003 Warning label 1
46 363977 Warning label 2
47 366061 Safety label

Preparing for commissioning

 To achieve flawless functioning of the machine, please
follow the instructions listed:
 Place the machine at a location that meets the following
conditions:
 secured against slipping
 free of vibrations
 even
 free of tripping hazards
 adequate light
 Before each use, check
 Connection cables for defects (cracks, cuts, etc.)
Do not use any defective cables.
 the saw blade for flawless condition
 Do not use deformed or damaged saw blades.
 Immediately replace a worn or damaged table insert.
 Connect the machine to a dust collection device when
sawing wood.
 To ensure a safe position of the saw it must be bolted down
on a solid surface (e.g. workbench or support frame) at
optimal working height.
20
Mounting on a workbench / work table:
 
Place the device on a level flat workbench or work
table.

An uneven surface may result in saw blade jamming
or inaccurate cutting.
 Make 4 holes in the workbench / work table matching the
holes in the base plate (39).
 Bolt the device down.
If the saw cannot be mounted on a workbench
or work table, insert the anti-tip device (40) in the
provided holes on the rear of the rotary table. Secure it
using two screws.
Removing the transport locking pin
Remove the transport locking pin before use: 
 Slightly push the handle (1) down.
 Pull out the transport locking pin (5).

Commissioning

Mains connection
Compare the voltage listed on the device type plate, e.g. 230 V,
with the mains voltage and connect the device to the
corresponding and proper socket.
Connect the machine via a 30 mA fault-current circuit breaker.
Use the connection or extension cable according to IEC 60245
(H 07 RN-F) with a core cross-profile section of at least
1.5 mm for cable lengths up to 25 m

2
2.5 mm for cable lengths over 25 m

2
On / Off Switch
Do not use any device where the switch can not be
switched on and off. Damaged switches must be repaired or
replaced immediately by the customer service.
Switch on

Activate the On/Off switch (1A).
Switching off
Release the On/Off switch again.
Switching on the laser
Press the On/Off switch for the laser (1B).

Only switch on the laser when a work piece is on the rotary
table.

Dust/chip exhaustion

The wood dust generated during operation impedes the
necessary view and is harmful to health to some degree.
Unless the machine is used outdoors, the dust bag (23) or a
chip exhaust system (e.g. portable dust remover) must be
connected.