Maintenance And Cleaning - ATIKA KGSZ 305 N Notice Originale

Straight cuts

1. If required, loosen the incline angle locking knob (25) and
adjust the saw head to its vertical position.
2. Retighten the incline angle locking knob.
3. Loosen the locking screw (7) for the rotary table (8), pull the
locking (7A) out and turn the saw head to the 0° position.
4. Firmly tighten the locking screw again
5. Narrow work pieces:
Slide the saw head to the rear position of the pulling device
and tighten the locking screw (6) for the pulling device.
Wide work pieces:
Slide the saw head to the rear position of the pulling device
and let the locking screw (6) for the pulling device loosened.
6.  Place the work piece against the stop (11) and clamp
it using the vice assembly (20).
7.  Switch on the saw.
8. Wait until the saw blade has reached its full speed.

9. While holding the On/Off switch (1A), push the lock for the
pendulum cover (17) away from the handle.
10. Slowly lower the saw head using the handle and cut evenly
through the work piece up to the table insert.
11.  Wide work pieces:
Pull the saw head to you in order to cut through the work
piece.
12. Lift the saw head until the saw blade is no longer in the work
piece.
13. Let the On/Off switch go and lift the saw head again.
Mitre cuts
The mitre angle can be set left and right from 0° to 45°. The
table locks in place at frequently required positions.

1. Loosen the locking screw (7) for the rotary table (8), pull the
locking (7A) out and turn the saw head to the desired angle.
2. Firmly tighten the locking screw again
3. Cut the work piece as described under "Straight cuts".
Inclined cuts
The saw head's angle of inclination can be adjusted from the
vertical position (0°) up to 45° to the left or right.
 ,
1.
Loosen the locking screw (11B / 11D) for the additional stop
(11A / 11C) and slide it to the desired position.
2. Firmly tighten the locking screw again
3. Incline the saw head to the left to the desired angle.
4.
To incline the saw head to the right remove the RH
additional stop (11A) and pull out the anti-swivel device
(25A).
5. Retighten the incline angle locking knob.
6. Cut the work piece as described under "Straight cuts".
Double mitre cuts
Increased danger of injury exists with the double mitre
cut because of the saw blade being more accessible
due to its heavy incline. Keep your hands far enough
away.
 , ,
1. Lösen Sie die Feststellschraube (7) für den Drehtisch (8),
ziehen Sie die Arretierung (7A) und schwenken Sie den
Sägekopf bis zum gewünschten Winkel.
2. Firmly tighten the locking screw again
3. Lösen Sie die Feststellschraube (11 B / 11 D) für den
Zusatzanschlag (11 A / 11 C) und schieben Sie ihn in die
gewünschte Position.
4. Retighten the incline angle locking knob.
5. Loosen the incline angle locking knob (25) and incline the
saw head up to the desired angle to the left.
6. Um den Sägekopf nach rechts zu neigen, nehmen Sie den
Zusatzanschlag rechts (11A) ab und ziehen Sie die
Schwenksicherung (25A) heraus.
7. Retighten the incline angle locking knob.
8. Cut the work piece as described under "Straight cuts".
Setting the groove depth
This function allows you to cut grooves into the work piece. The
work piece is only cut to a certain (set) depth and is not cut
through.
Groove cutting poses an increased risk of injury since
the saw head may bounce upward. Do not exert any
lateral pressure on the saw blade. Firmly secure the
work piece with the vise assembly (20).
1. Set the saw head and rotary table to the desired position and
lock it in place.

2. To finely adjust the groove depth loosen the locking nut (33)
for the set screw (32).
 The saw head rises when you turn the set screw (32)
counterclockwisely → deeper groove.
 The saw head lowers when you turn the set screw (32)
clockwisely → more shallow groove.
3. Retighten the locking nut (33) for the set screw (32).
4. Firmly secure the work piece with the vice assembly (20).

The groove is cut over the whole length if you place a
stop attachment between work piece and work piece stop.
5. Cut the work piece as described under "Straight cuts".

Maintenance and cleaning

Before each maintenance and cleaning work
 switch off device
 Wait for standstill of the saw blade
 pull out power plug
Further maintenance and cleaning works than described in this
chapter shall only be carried out by the manufacturer or
companies named by the manufacturer.
For maintaining and cleaning, removed security devices must
unconditionally be mounted properly and proved again.
Use only original parts. Other parts can result in unexpected
damages and injuries.
23