Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
23. Calling with more than one handset
If you have more than one handset registered to the same base, you can
make internal calls, transfer external calls between the registered
handsets, and set up a conference call.
23.1 Internal call
!
Press the
key. The display shows the following message:
- Intercom
-
1 2 3 4 5
Back
!
Enter the number of the handset you want to call (e.g. "3" for handset
3).
If the handset entered is valid, the called handset will ring and
display "HS X Calling".
!
The handset user can press the
!
To end your conversation, press the
Notes:
If an external call comes in during an internal call or a conversation with the
door unit, the display will show the caller's number and two short beeps will
be heard.
!
Press the
key to end the internal call. Shortly after that your
telephones will ring with the incoming call.
!
Now answer the external call with the
It is not possible to call a door unit from a handset.
23.2 Call transfer between handsets
You can transfer an external call between handsets that are registered to the
same base.
!
During an external call, press the
!
Enter the number of the handset you want to transfer the call to.
!
If the called party wants to answer your call, he/she can press the
key to talk with you. At this time you can inform him/her of the
incoming call.
!
When the called party wants to answer the external call, press the
key or replace the handset to the base to complete the transfer.
23.3 Setting up a conference call
When you have both an external call and an internal call in progress, you can
set up a 3-way conference call like this:
1. During an external call, press the
the handset you want to join the 3-way call.
2. The called party presses the
3. The calling party presses the
4. Either of the two handsets can press the
call at any time.
page 69
key to answer the internal call.
key.
key.
key.
key and then enter the number of
key to answer.
key to start the 3-way call.
key to leave the conference
Note:
If one of the handsets leaves the conference call, the remaining handsets will
continue the conference.
24. Caller ID on call waiting
When you subscribe to Call Waiting service from your local telephone
company, the handset will display the name and number of the second caller
while you are having a conversation.
!
Press the "flash"
key to answer the second caller.
!
If you press the
"flash"
conversation with the first caller.
Note:
If you have transferred an external call to another handset, you cannot use
the call-waiting function via the second handset.
25. Changing batteries
25.1 Door unit
If the ring tone at the door unit is weak or no communication is possible, the
batteries in the door unit should be replaced:
!
Use the supplied torx wrench [24] to remove the torx screw [23] from the
hole [12].
!
Pull the door unit [1] upwards and out of the bracket [15].
!
Open the battery compartment [13] of the door unit by sliding the
battery compartment cover [11] down.
!
Remove and dispose of the old batteries.
!
Insert two new alkaline LR14 (C), 1.5 V batteries into the battery
compartment, watching for the correct polarity. The door unit will ring
once.
!
Replace the battery compartment cover.
!
Slide the door unit back onto the bracket.
!
Screw the torx screw back into the door unit.
25.2 Handset
If the batteries in the handset discharge too quickly, they should be replaced:
!
Open the battery compartment [53] of the handset [39] by sliding the
battery compartment cover [55] down.
!
Remove and dispose of the old batteries.
!
Insert two new Ni-MH batteries AAA, 1.2 V; 600 mAh batteries into the
battery compartment, watching for the correct polarity.
!
Replace the battery compartment cover.
key, you can continue with your
GB - 69
Publicité
Chapitres
Table des Matières
