Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
!
Press the
"Select"
key.
!
Use
and
key to select "Dial Mode".
!
Press the
"Select"
key.
!
Use
and
key to select the desired dialling mode (Tone or
Pulse).
!
Press the
"Save"
key.
Note:
If you are not sure which dialling mode to select, please contact your local
service provider.
Factory default: Tone
20.3 Flash Time
This setting is only necessary if required by your telephone system. See the
user manual of the telephone system.
You can change the Flash time with the following steps:
!
Press the "Menu"
key.
!
Use
and
key to select "BS Settings".
!
Press the
"Select"
key.
!
Use
and
key to select "Flash Time".
!
Press the
"Select"
key.
!
Use
or
key to select "Flash-1" (short) or "Flash-2" (long).
!
Press the "Save"
key.
Factory default: Flash-1
20.4 Modifying the PIN (Modify PIN)
This function allows you to change the PIN number of the currently active
base. The default PIN is 0000.
!
Press the "Menu"
key.
!
Use
and
key to select "BS Settings".
!
Press the
"Select"
key.
!
Use
and
key to select "Modify PIN".
!
Press the
"Select"
key.
!
Enter the current PIN.
!
Press the "Next"
key. The display shows "New PIN".
!
Enter a 4-digit new PIN.
!
Press the "Next"
key. The display shows "Repeat".
!
Enter the new PIN again.
!
Press the "Save"
key to confirm. Now your new PIN is activated.
Note:
It is important that you memorize your new PIN.
PIN, you cannot make any modifications to the device which require a PIN.
20.5 Resetting the base (BS Reset)
This function allows you to reset the base setting to the factory default.
GB - 66
page 66
"Terminate HS" appears.
The display shows the actual setting.
A confirm beep will be heard.
"Terminate HS" appears.
The display shows the current setting.
"Terminate HS" appears.
The display shows "PIN ?".
If you loose your
!
Press the "Menu"
key.
!
Use
and
key to select "BS Settings".
!
Press the
"Select"
key.
!
Use
and
key to select "Flash Time".
!
Press the
"Select"
key.
!
Enter the current PIN code.
!
press the "Reset"
key.
21. Handset settings (HS Settings)
21.1 Alarm
You are able to set the alarm on the handset.
!
Press the "Menu"
key.
!
Use
and
key to select "HS Settings".
!
Press the
"Select"
key.
!
Press the
"Select"
key.
!
Use
or
key to select "On" or "Off".
!
Press the "Select"
key.
!
If you select ON, the display shows the current alarm time.
#
Enter the new time with numeric keys 0 to 9 in 24h format HH:MM.
#
Press the "Next"
key. A beep sounds.
#
Press
or
key to enable or disable the snooze function
#
Press the "Save"
key.
Notes:
If you choose "Snooze Off", the alarm will ring for about 40 seconds at the
selected time. By pressing any key you can switch off the alarm at any time.
To deactivate the alarm, choose "Off" in the "Alarm" menu, otherwise the
alarm will ring again the next day.
If you choose "Snooze On", the alarm will ring in regular intervals approx.
every 10 minutes till the batteries of the handset are empty. By pressing any
key (not the
key) you can switch off the alarm at any time, after 10
minutes the alarm will ring again. To switch off the alarm, press the
The alarm will ring again the next day. To deactivate the alarm, choose "Off"
in the "Alarm" menu, as described above.
Factory default: Off
21.2 Adjusting the volume (Audio Setup)
You can adjust the volume of the handset or the speaker when using the
hands-free function as follows:
!
Press the "Menu"
key.
!
Use
and
key to select "HS Settings".
!
Press the
"Select"
key.
!
Use
and
key to select "Audio Setup".
!
Press the
"Select"
key.
!
Use
or
key to select "Speaker V." or "Earpiece V.".
"Terminate HS" appears.
The display shows "PIN?".
"Alarm" appears.
The display shows the current setting.
"Alarm" appears.
key.
Publicité
Chapitres
Table des Matières
