Electrical Safety; Before The First Start-Up; Start-Up; Mains Connection - ATIKA ADH 254 A Notice Originale

Electrical safety

Extension cable to be designed in compliance with IEC 60
245 (H 07 RN-F) having a core cross-section of at least:
− 1.5 mm² for cable lengths up to 25 m
− 2.5 mm² for cable lengths over 25m
Long and thin connection lines result in a potential drop. The
motor does not reach any longer its maximal power; the
function of the device is reduced.
Plugs and coupler outlets on connection cables must be
made of rubber, non-rigid PVC or other thermoplastic
material of same mechanical stability or be covered with this
material.
Protect yourself against an electric shock. Avoid touching
earthed parts with your body.
The connector of the connection cable must be splash-proof.
Wind off completely the cable when using a cable drum.
Do not use the cable for purposes for which it is not meant.
Protect the cable against heat, oil and sharp edges. Do not
use the cable to pull the plug from the socket.
Regularly check the cable and if damaged, have it renewed
by a recognised skilled electrician.
When running the connection line observe that it does not
interfere, is not squeezed, bended and the plug connection
does not get wet.
Regularly check the extension cables and replace them if
they are damaged.
Do not use any defective connection cables.
Do not set up any provisional electrical connections.
Never bypass protective devices or deactivate them.
Only hook up the machine by means of a fault-current circuit
breaker (30 mA).
The electrical connection or repairs to electrical parts of the
machine must be carried out by a certified electrician or
one of our customer service points. Local regulations –
especially regarding protective measures – must be
observed.
Repairs to other parts of the machine must be carried out
by the manufacturer or one of his customer service points.
Use only original spare parts and accessory parts.
Accidents can arise for the user through the use of other
spare parts. The manufacturer is not liable for any damage
or injury resulting from such action.

Before the first start-up

To achieve flawless functioning of the machine, please
follow the instructions listed:
Place the surface planing and thicknessing machine at a
location which meets following conditions:
− secured against slipping
− free of vibrations
− even
− free of tripping hazards
− adequate light
Before each use, check
− Connection cables for defects (cracks, cuts, etc.).
Do not use any defective cables.
− whether the pushstick is to hand
− Is the unused blade shaft covered by the blade shaft
guard?
When working do not stand directly in front or behind the
machine but stand to the side.
You have to attach the following parts:
A1 - A7
Base frame
Assemble the four parts of the stand as shown in the figures
A1 through A7.
Use a second person to place the surface planing and
thicknessing machine on the stand.
Secure the surface planing and thicknessing machine to the
stand.
Securing on the floor
Secure the surface planing and thicknessing machine to the
floor using 4 screws.
Guide plate
Secure the guide plate guideway (7) to the housing.
Slide in the guide plate holder (10) and secure the locking
lever (12).
Mount the guide plate (13).
Shavings exhauster
Install the shavings exhauster connector (16).
Connect the shavings exhauster hose (17) and secure it
using a hose band clip (18).
Connect the shavings exhauster hood (27) to the exhaust
hose and tighten the hose band clip.
Attach the shavings bag (19) to the exhauster connector and
secure it using the hose band clip.

Start-up

Mains connection

Compare the voltage listed on the machine's type plate, e.g.
230 V, with the mains voltage and connect the machine to a
suited and properly earthed electrical socket.
Alternating current motor:
Use a shockproof plug, mains voltage 230 V with residual
current circuit breaker and min. 10 A inert fuses.
Three-phase motor:
CEE socket, 3-pin, mains voltage 400 V with earth-leakage
circuit breaker and min. 10 A fuse.
Use connection cable or extension cable respectively with a
cross section of at least 1.5 mm².
15
A8
C1 - C7