ATIKA ADH 254 A Notice Originale page 18

Planing and joining workpieces
Adjusting the guide plate
1. Loos en the locking lever (12).
If you can not sufficiently turn
lever head and turn it back.
2. Tilt the guide plate to your desired angle which you can read
from the angle scale (40). Make sure that the lower edge of
the guide plate is above the table edge when tilting.
3. Tighten the locking lever (12) again.
Adjusting the depth of cut
1. Turn the adjusting screw for the dept
2. You can read it from the depth of cut scale (45).
Adjusting the blade shaft guard
1. Pus h the workpiece against the guide plate
2. Loosen the clamping device for the blade shaft gu
3. Turn the adjusting screw (30) to adjust the arm of the blad
shaft guard.
4. For flat workpieces (< 75 mm):
Push the blade shaft guard (23) aga
and lift it according to the workpiece thickness. Turn
therefore the adjusting screw (30):
Push the workpiece somewhat below the blade shaft guard
and lower the latter onto the workpiece.
5. For high workpieces (> 75 mm):
Lower the blade shaft guard down to th
push it against the workpiece.
Planing
1. S ar t t the motor .
2. Push the workpie ce right-angled over the feed table plate.
3. Hold your fingers close to each other and guide th
workpiece with flat hands over the feed table plate.
4. When planing narrow surfaces (joining edges) push the
workpiece with both hands and clenched fists against the
guide plate and the table plate and push it over the feed
table plate.
5. When planing and joining short workpieces use the push
stick (31)
6. Press down the workpiece only on the delivery table.
7. Turn the machine off if the work is not imme
continued.
Skewing
1. Plac e the workpi ece against the tilted guide plate.
2. Adjust the blade shaft guard so that it just conta
workpiece.
3. With your left clenched fist press the workpiece against the
guide plate and the delivery table plate. Push the workpiece
with your closed right hand over the feed table plate.
the locking lever, pull out the
E8
h of cut (29)
.
ard (46)
inst the guide plate (13)
e table plate and
E12
diately
cts the
4. Turn the machine off if the work is not immediately
continued.
Thicknessing
The purpose of thi
already planed surfa
For this the workpiece is guided through the machine and
machined on its top surface. Th
the thicknessing table plate. The feed direction is exactly the
other way round as for planing from left to right.
When thicknessing a step will be formed on the lead and
tail edges of the workpieces. Therefore cu
to length only after thicknessing
Prep arations:
Pull the mains plug before performing
settings.
Installing the dust extractor
1. Loos en the locking lever (46) and pu
e
gu ar d off from the table plate.
2. Adjust the guide plate (13) to 90° and slide it beyond the
edge of the table plate.
3. Place the extractor hood (27) onto the planing plate. Slide
two fixing brackets in the
4. Make sure that the shavings exhauster hose and the bag
are secured.
Thicknessing
1. Mak e sure that the th
top p osition.
2. Adjust the depth of cut.
In a single pass th
maximum. Howeve
e
− your blades are very sharp,
− you machine soft wood types,
− you machine workpieces the
smaller than the maximum width
3. Start the motor.
4. Push in the workpiece slowly and right-
direction. It will b
5. Guide the workpiece straight through the machine.
6. Turn the machine off if the work is not im
continued.
17
cknessing is to make the workpiece with
ce thinner.
e already planed surface faces
sh the blade shaft
grooves of the table plate.
icknessing adjusting lever (35) is in its
e machine can cut 2 mm as a
r do only adjust this depth if:
width of which is
.
e drawn in automatically.
t the workpiece
angled in arrow
mediately