Maintenance And Cleaning; Transport - ATIKA ADH 254 A Notice Originale

Maintenance and cleaning

Before each mainte
− switch off device
− wait until the machine comes to a stop.
− pull out power plu
Maintenance an d re pair work other than t
chapter is only a llowed to be carried out b
For maintaining and cleaning, removed security devices must
unconditionally be mounted properly and proved again.
Use only original parts. Other parts can result in unexpected
damages and injuries.
Cleaning
Observe the following to maintain the operability of the
machine :
Do not wash down device with water.
R emove sp lints and dust only with a brush or vacuum
cleaner.
Slightly spray maintenance spray or dry-film lubricant on the
height adj ustment device of the thicknessing table.
Take care that the feed rollers remain free of rust and
resin.
Remove resin residues from the table plate surfaces.
Resin residues can be removed with a commerc
main nance and care spray. te
Apply a thin film of sliding wax on the feed, delivery and
thicknessing table plates.
Regularly remove resin from the blade shaft and from the
parts attached to it. For
device, the blade holders and the blades into paraffin,
gasoline or commercial resin remover for 24 hours.
Carefully shake out the shavings bag. Manually wash it in
case of heavy soiling but at least once a year wit
soap solution.
M a intenance
The cutting blade s are wearing parts and will become dull after
longer or frequen t use.
If so, replace the cutting blades or have them sharpened.
Regrinding of cutting blades is only allowed to a height o
15 mm.
Alwa ys use cutting blades which are approved for the machine
(s ee "T echnical data").
Replace or sharpen both cutting blades together.
Before replacing or sharpening
blades unplug the machine.
Danger of cutting! Wear gloves when replacing the
cuttin b g lades.
nance and cleaning work
g
hose described in th
y service staff.
this purpose put the clamping
h a mild
the cutting
Replacing the cutting blades
1. Adju st the guide plate (13) to 90° and
ed ge of the table plate.
2. Loosen the locking lever (46) and push the blade shaft
guard off from the table p
3. Screw in the clamping screws (34) using the delivered open-
is
end spanner (32).
If the nuts are not visible, carefully turn the blade shaft (47)
using a waste wood block.
4. Remove the blade (33).
5. Clean all parts including the
6. Reinstall a new or sharpened blade.
7. Align the blade:
− Place the setting gauge (53) for th
the delivery ta
− Firmly press the gauge onto the delivery table plate while
making sure that the edge
with the edge of the delivery table plate.
−
Then, the setting gauge presses the blade in its correct
position.
− Retighten the clamping screws.
−
When doi ng so start in the centre and move outwards.
8. Replace also the other blade of the b
9. Push the blade shaft guard over the blade shaft.
Maintenance of the gearbox
ial
Perform the following steps approx.
hours:
1. Remove the gearbox cover (48).
2. Rem ove wood dust and shavings using a vacuum or a
brush.
3. Slightly spray maintenance spray on the roller chain (44)
and on th e bearings of the belt roller and pulley.
Do not use grease.
4. Re-mount the gearb

Transport

Remove mains plug before each transport.
Before any transport make sure that the blade shaft guard
f
fully covers the blade shaft.
This will avoid injury by the blades.
Two persons are required to li
18
slide it beyond the
late.
G1 - G2
G3
blade slots in the blade shaft.
e cutting blades onto
ble plate.
of the setting gauge is flush
lade shaft.
every 50 operating
ox cover.
ft the machine.
G4