Robert Juliat TOPAZE 1119 CS Dossier Technique page 6

Please read carefully all the instructions before operating the appliance.
GENERAL INSTRUCTIONS
1. Not for residential use.
2. Only qualified technicians are permitted to service these fixtures.
3. In addition to the instructions indicated on this page, you must
adhere to the relevant health and safety requirements of the
appropriate EU Directives.
4. This fixture is in compliance with section 17: Lighting appliance
for theatre stages, television, cinema and photograph studios.
Standards NF EN 60598-1 and NF EN 60598-2-17.
5. This fixture is rated as IP20, and is for indoor use only.
FIXTURE
6. Warning:
high voltage ignition. Disconnect from the mains before
any servicing.
7. Make sure the fixture is correctly mounted on an appropriate
support.
8. The protection screens, lenses or U.V. filters must be replaced if there
is any visual damage which might reduce their performance, for
example, by cracks or deep scratches.
9. When hung or flown the fixture must be secured by another hanging
accessory (such as a safety cable or bond) that is of suitable length.
10. The safety bond or cable must be securely attached at the back of
the fixture. It must be as short as possible or rolled up as necessary
to ensure the fixture does not travel any distance should it be
dislodged.
11. Movable accessories (barn doors, HMI shutters, spill rings etc.) must
also be secured with a suitable safety cable or bond at the front of
the fixture.
12. Take into account the weight of both the fixture and the accessories
when choosing the strength of the attachment point and the safety
cable or bond.
13. Do not open the lighting fixture when the lamp is on.
14. Both the lamp and lamp housing heat up when powered. Wait until
the fixture is cold before servicing.
15. Do not tamper with the design of the fixture nor any of its safety
features.
16. Tighten the electrical mains cable connections regularly. Replace
mains cable with an identical one if damaged.
17. Use only with correct power supply.
Ventilation
18. Keep well away from flammable material.
19. Do not use outside. Do not cover. Do not permit the fixture to get
wet.
20. To avoid overheating, do not obstruct air vents.
21. If the fixture has fans, make sure they are working correctly. If fans
are not working, turn the fixture off immediately and service as
necessary.
robert juliat
Route de Beaumont F 60530 Fresnoy-en-Thelle phone: +33 (0)3.44.26.51.89 - fax: +33 (0)3.44.26.90.79 - www.robertjuliat.fr
TECHNICAL FILE
USER'S INSTRUCTIONS
1200W MSD COLD STRIKE FOLLOWSPOTS
Lamp
22. Use only fully enclosed in the fixture.
23. Never look at the lamp directly.
24. Warning: U.V. rays : Protect your eyes.
25. Check that the lamp voltage corresponds to the mains voltage used.
Do not use a lamp with power that is an incorrect type or voltage to
the one that is indicated on the lamp housing or packaging.
26. The lamp must be replaced if it has been damaged or deformed by
the heat.
27. Use only when bulb is in place.
Cleaning
28. Do not touch the lamp or the mirror with your fingers.
29. Keep optical parts (lens, lamps,...) clean with alcohol.
30. Regularly remove dust from the mirror with a soft and clean rag.
31. If the fixture has filters they must be cleaned frequently.
POWER SUPPLY
32. Disconnect from the mains before any servicing.
33. Mains connection only. Do not connect to an "electronic output"
(dimmer, static relay...).
34. Do not use outside. Do not cover.
35. The power supply has circuit breakers, which should always be kept
accessible.
36. There is no maximum distance between the lighting unit and the
power supply.
37. Check the mains voltage.
PLEASE NOTE
These products have been built to conform to European standards
relating to professional lighting equipment. Any modification made to
our products will void the manufacturers' warranty
Danger
The discharge lamp used emits short-wave ultraviolet
radiation which is harmful to skin and eyes.
1119 CS & CCS
1419 CS & CCS
Section A - 1