Assembly & Installation - Cub Cadet 49A70001100 Manuel D'utilisation

NOTE:
References to left, right, front and rear of the tractor are from the operator's position, unless
otherwise stated.
• Before assembly, place the tractor on a firm, level surface, disengage the
PTO, stop the tractor engine and set the parking brake.
Assemble Mounting Plate & Strut Brackets
1. Place the two strut brackets
(789-04278) facedown on a
stable work surface, as shown in
Figure 3.
NOTE:
Slots on strut brackets should be
faced to the outside, while smaller holes
should be facing in.
2. Align mounting plate (689-
02559) to strut brackets with
flanges curving inward and solid
flange lined up with smaller
holes along the bottom of strut
brackets. See Figure 3.
3. Secure mounting plate and strut brackets with four hex head screws (710-1238)
and four lock nuts (712-04063) from hardware pack 689-02619. See Figure 3.
4. Set assembly aside for installation later in these instructions.
Install Brackets on
Tractor Frame
NOTE:
When assembling these mounting
brackets, it is best to not fully tighten the
brackets at this time. This will facilitate the
mounting process in later steps, which will then
require fully tightening this mounting assembly.
Install lower bracket as follows:
1. Align lower bracket (789-04279)
with the holes on the lower rear
tube of tractor frame with side
flanges pointing up, secure with
two self-tapping hex head screws (710-1238). See Figure 4.
NOTE:
Two bolts should be pre-installed on the tractor. These can be re-used. If these bolts
are not pre-installed, use provided bolts to secure the bracket to the two inner rivnuts on
muffler bracket.
Install upper bracket as
follows:
1. Working from the
inside out, align
keeper bracket (689-
02519) with upper rear
tube of tractor frame,
sliding weld pins into
existing holes on
underside of tube. See
(1) in Figure 5.
2. Working from outside
in, align upper bracket (789-
04458) with upper rear tube of
tractor frame and keeper bracket,
aligning upper and lower holes of
both brackets. See (2) in Figure 5.
3. Holding both brackets in place,
loosely secure assembly around
frame tube with four hex head
screws (710-1238) and four lock
nuts (712-04063). See Figure 6.
ASSEMBLY & INSTALLATION
4.
Install Mounting Plate/Strut Bracket Assembly
1.
2.
3.
Figure 3
4.
Install Vertical Bagger Support
NOTE: This manual covers various bagger
configurations. Please follow the instructions
applicable to your machine.
1.
Figure 4
2.
3.
Install Hanger Assembly
1.
Figure 5
NOTE:
placed on same side as flange lock
nuts (towards frame).
NOTE:
0276), from hardware pack 689-
02619, go in the top holes with the
nuts facing the engine. The hex bolt
(710-1238), from the same hardware
Figure 6
pack, goes in the bottom hole.
6
Once aligned, tighten all of the hardware installed at this time.
Install mounting plate/strut
bracket assembly onto lower
bracket previously attached to
frame by aligning interior holes
on struts with holes on upright
flanges of lower bracket.
Working from inside-out, secure
mounting plate/strut bracket
assembly to lower bracket with
two hex head screws (710-1238)
and two lock nuts (712-04063).
See (1) in Figure 7.
Swing upper arms of mounting
plate/strut bracket assembly
toward tractor frame, aligning
outside slots with holes on downward
flanges of keeper bracket previously
attached to frame. See (2) in Figure 7.
Working from outside-in, secure
mounting plate/strut bracket
assembly to keeper bracket with two
hex head screws (710-1238) and two
lock nuts (712-04063). See Figure 8.
Using Figure 9, locate the correct
mounting hole location on the mounting
plate for your tractor.
Install the vertical bagger support (683-
04519C) onto the mounting assembly on
the tractor by hooking it over the
mounting assembly, as shown in
Figure 10.
Secure the vertical bagger support
to the mounting assembly using
a hex bolt (710-06154B) from
hardware pack 689-02619. See
Figure 10.
Install and secure the hanger
assembly (683-04498B) onto the
vertical bagger support using three
carriage bolts (710-0276), three
cup washers (736-0242) and three
flange lock nuts (712-
04063) from hardware
pack 689-02619. See
Figure 11.
Cup washers should be
The carriage bolts (710-
Figure 7
Figure 8
48 48 54 54 60 60
" " " " " "
Figure 9
Figure 10
Figure 11