Quick RIDER REGAL R 1724 Manuel De L'utilisateur page 17

POS. DESCRIPTION
13 Regal base
14 Rider base
15 Sensor
16 Regal barbotin lock pin
17 Regal spring
18 Screw
19 Rope/chain stripper Regal
20 Screw
21A Chain pipe SX
21B Chain pipe DX
22 Gypsy Regal lock lever
23 Plug
24 Screw
25 Screw
26 Rope/chain stripper Rider
27 Chain release support cam
28 Gypsy lock pin cam
29 Handle
30 Plug
31 Screw
32 Chain release support
33 Rider spring
34 Gypsy Rider lock pin
35 Short shaft 23/3000W
36 Long shaft 23/3000W
37 Long shaft 17/2000W
38 Short shaft 17/2000W
39 Key
40 Key
41 Key
42 Key
43 Studs
44 Flange gearbox 3000W
45 Screw
46 Washer
47 Spring washer
48 Nuts
49 Washer
50 Spring washer
51 Nuts
RIDER REGAL 1700/2000/2300/3000W - REV004A
CODE
SLMSC20RGDSX
SGMSC30C0000
SAKREED00000
Quick
MSVPR20RG000
ant to marine environments. In any case, any salt deposits
MMLMS2000000
on the outside must be removed periodically to avoid corro-
MBV0816MXCE0
sion and damage to the equipment.
MSN200000R01
The parts where salt may have built up should be washed
MBV1020MXCE0
thoroughly with fresh water.
MSS20SX00R01
MSS20DX00R01
Once a year, the drum and the gypsy are to be taken apart
PDLVBL200000
as follows:
MBSE04016A00
MBV1010X0000
DRUM VERSION
MBV0816MXTSC
Use the handle (1) to loosen the bush (2); pull off the drum
SPMSN20CX000
(3) and the top clutch cone (5); loosen the fi xing screws (18)
MSVCM20S0000
of the chain stripper (19) and remove it. Pull off the gypsy (6).
MSVCM20P0000
NO-DRUM VERSION
PVPMESALPA00
MBSC04020A00 Use the handle (1) to loosen the bush (2); to remove the
gypsy cover (4); and the top clutch cone (5); loosen the fi xing
MBV1040MXTSC
screws (18) of the chain stripper (19) and remove it. Pull off
SPMSN20AXS00
the gypsy (6).
MMPMS2000000
MSVPR2000000
Clean all the parts removed to avoid corrosion, and grease
MSAS30387R00
the shaft thread (35, 36, 37 or 38) and the gypsy (6) where
MSAS30448R00
the clutch cones rest (5 and 7) (use grease suitable for ma-
MSAS17448R00
rine environment).
MSAS17387R00
MBH1008060X0
Remove any oxide deposits from the terminals of the elec-
MBH0807040X0
tric motor and the contactor unit; grease them.
MBH1008140X0
MBH0807140X0
MBP101109X00
MTFANRD30000
MBV0825MXTSC
MBR08X000000
MBG08X000000
MBD08MXEN000
MBR10X000000
MBG10X000000
MBD10MXEN000
MAINTENANCE
WARNING: make sure the electrical power to the
motor is switched off when working manually on the
windlass. Carefully remove the chain from the gypsy
or the rope from the drum.
® windlasses are manufactured with materials resist-
GB
17