1. Manuels
  2. Marques
  3. Swing-N-Slide Manuels
  4. Ensembles de jeux et équipements de terrains de jeux
  5. NE 5010 ProJect 512
  6. Manuel d'instructions

Swing-N-Slide NE 5010 ProJect 512 Manuel D'instructions

Masquer les pouces
Table des Matières

Publicité

Liens rapides

Télécharger ce manuel
Assembly InstructIons
no. of children: Up to 10
min. use Zone: 30 ' x 33-1/2 '
set Dim. 17 'W x 21-1/2 'L x 13'H
est. building time: 4-6 hr.
PLEASE READ BEFORE BEGINNING ASSEMBLY!!
Please make sure all lumber, hardware and accessory parts are accounted for. If you are missing
Do not return
anything, please
Other benefits include information on product warranties, assembly plan updates, joining our
mailing list for new products and promotions, receiving our newsletter, and providing feedback on
ImPortAnt!!
Service Department at the number below.
to register your product visit:
http://www.swing-n-slide.com
Swing•N•Slide • 1212 Barberry Drive • Janesville, Wisconsin 53545
Visit our web site at: www.swing-n-slide.com or call us at
1-800-888-1232
to the store where purchased. Please call our Customer
products.
ne 5010
ProJect 512

Publicité

Table des Matières
loading

Manuels Connexes pour Swing-N-Slide NE 5010 ProJect 512

Sommaire des Matières pour Swing-N-Slide NE 5010 ProJect 512

  • Page 1 Other benefits include information on product warranties, assembly plan updates, joining our mailing list for new products and promotions, receiving our newsletter, and providing feedback on products. Swing•N•Slide • 1212 Barberry Drive • Janesville, Wisconsin 53545 Visit our web site at: www.swing-n-slide.com or call us at 1-800-888-1232...

  • Page 2: Disposal Instructions

    When the equipment is taken out of service, it must be disassembled and disposed of in such a way that no unreasonable hazards will exist at the time the set is discarded. Important! Additional Safety Instructions for all Swing-N-Slide Playground Equipment. Save this instruction sheet in the event the manufacturer needs to be contacted.
  • Page 3 Swing-N-Slide® will repair, or at its discretion, replace any part within the stated warranty period which is defective in workmanship or materials. This decision is subject to verification of the defect upon delivery of the defective part to Swing-N-Slide® at 1212 Barberry Drive, Janesville, Wisconsin, 53545. Any part(s) returned to Swing-N- Slide®...

  • Page 4: Tools Required

    ProJect 512 TOOLS REQUIRED HAmmer cIrculAr sAW 1/2" socKet & WrencH electrIc DrIll sAFety GlAsses cArPenter's sQuAre 3/8" DrIll bIt (6'' min.) PHIllIPs bIt tAPe meAsure & Dust mAsK (2) 1/2'' panhead screws (18) 5/16'' flat washers (4) 1'' truss screw (6) T- nuts (8) 1-3/4'' panhead screws (8) 1/4'' flat washers...
  • Page 5 AGES 2-10 YEARS For Home / Residential Use ONLY 1212 Barberry Drive (4) Climbing Rocks Janesville, WI 53545 1-800-888-1232 with Hardware www.swing-n-slide.com (1) Name Plate (1) Multicolor Tarp (4) Swing Hangers (1) T30 Torx® Bit Kodiak Plan (1) Plan (4) Safety Handles (2) Swing Seats weight limit: 115 lbs.
  • Page 6 ProJect 512 KODIAK 512 OPTIONAL LADDER 3 - 2"X4"X96" 11 - 2"X4"X120" 1 - 2"X4"X96" 7 - 5/4"X6"X120" 2 - 2"X4"X120" 15 - 5/4"X6"X144" OPTIONAL ROCK WALL 8 - 4"X4"X96" 1 - 2"X4"X96" 5 - 4"X4"X120" 1 - 2"X4"X120" 1 - 4"X6"X144" 3 - 5/4"X6"X120"...
  • Page 7 ProJect 512 96'' 48'' "X6"X144" 48'' 48'' 48'' "X6"X144" 36'' 36'' 36'' 36'' "X6"X144" 54'' 40-3/4'' 36'' "X6"X144" 40-3/4'' 39-1/2'' 54'' "X6"X144" 47'' 47'' 30'' "X6"X144" 30'' 30'' 30'' 36-1/4'' "X6"X144" 96'' 4"X4"X96" 56'' 36'' 4"X4"X96" 73'' 4"X4"X96" 73'' 30'' 4"X4"X120"...
  • Page 8 ProJect 512 How to select the correct fastener Use these 3 pictorial guides to help select the correct fastener(s) for the lumber attachment you are making. Each diagram will highlight the correct number of fasteners to use, and where to attach them. 5/4'' x 6'' to 4'' x 4'' 2-1/2'' screws Apply the 2-1/2"...
  • Page 9 ProJect 512 Understanding how the Bracket System Works Example of a Shelf-Loc bracket connection. Shelf-Loc Bracket correct! Wrap-Loc WronG! brackets ''clipped'' brackets not interlocked! Example of a Shelf-Loc bracket connection. Look for ''TOP'' stamp on bracket for correct orientation. top of bracket Introduction to the Bracket system LW YS Use 2'' lag screws on all brackets.
  • Page 10 ProJect 512 •WARNING• Avoid splitting your lumber by offsetting Look for ‘’TOP’’ Use a 2’’ lag screw stamp on brackets your screws at least to hold bracket in while installing. place for later use. 3/4’’ from edge. Frame 1 Construction Fig.1 2-1/2'' screws per joint...
  • Page 11 ProJect 512 2-1/2'' screws Frame 2 Construction Fig.2 (2) 4'' x 4'' x 120'' 2-1/2'' screws 2'' lag screws per bracket 86'' 48'' 47'' 59'' 2'' Lag screw 2-1/2'' screw B. Frame 2 Construction 1. Measure and position brackets on 4'' x 4'' x 120’’ as shown in (Fig.2). 2.
  • Page 12 ProJect 512 Frame 3 Construction Fig.3 2-1/2'' screws (2) 4'' x 4'' x 120'' 2'' lag screws per bracket 92-1/2'' (1) 2'' lag screw 59'' 59'' (4) 2-1/2'' screws 47'' 2'' Lag screw 2-1/2'' screw C. Frame 3 Construction 1. Measure and position brackets on 4'' x 4'' x 120’’ as shown in (Fig.3). 2.
  • Page 13 ProJect 512 Fig.4 (1) 2'' lag screw (4) 2-1/2'' screws 2'' Lag screw 2-1/2'' screw D. Frame Construction 1.Install 5/4'' boards as shown above.
  • Page 14 ProJect 512 Fig.5 Double check to make sure structure is square 2-1/2'' screws 2-1/2'' screws 74-1/2'' (1) 2'' lag screw (4) 2-1/2'' screws D. Frame Construction cont. 1. Install 2'' x 4'' and 5/4'' boards as shown above. 2. Attach Frame 2 to Frame 1 as shown. 2'' Lag screw 2-1/2'' screw...
  • Page 15 ProJect 512 Tip: Flex brackets to make installation of 4'' x 4'' easier Fig.6 Fig. 6a Approx. 1/4'' 2'' Lag Screws Fig. 6b 2'' Lag screw F. Install 4x4s 1. Work (2) 4'' x 4'' into brackets as shown in (Fig.
  • Page 16 ProJect 512 Fig.7 Fig.8 Double check to make sure structure is square (1) 2'' lag screw (4) 2-1/2'' screws ttach Frame 3. 1. Attach and secure Frame 3 to rest of unit as shown above. 2'' Lag screw 2-1/2'' screw...
  • Page 17 ProJect 512 Fig.9 2-1/2'' screws per joint 2-1/2'' screw G. Install Deck Boards 1. Install 5/4'' deck boards to structure as shown (Fig. 9). 2. Use two 2-1/2'' screws at center and each end of deck boards. Note: For 5/4'' x 6'' x 47'' boards align 2-1/2'' screws horizontally to avoid hitting Shelf-Brackets beneath.
  • Page 18 ProJect 512 Fig.10 2-1/2'' screws per board 2'' screws 2-1/2'' screws J. Install Middle Rail Boards 1. Secure 4'' x 4'' support from above (Fig. 10) and and below deck as shown. 2'' screw 2. Secure 2'' x 4'' x 48-1/2'' as shown in (Fig. 10). 2-1/2'' screw...
  • Page 19 ProJect 512 2'' screw Fig.11 2-1/2'' screw 2'' Deck Screws UNDER-DECK VIEW 2-1/2'' screws H. Center & Entrance Support Boards Fig.11a 1. Construct support boards as shown in (Fig. 11). 2. Secure center of floor boards as shown in (Fig 11a) 2-1/2'' screws...
  • Page 20 ProJect 512 Fig.12 2-1/2'' screws per board 2-1/2'' screws per board I. Install Lower Rail Board 1. Install lower 2'' x 4'' rail board as shown in (Fig 12). Flush with the sides of 4'' x 4'' deck supports. Bottom of 2'' x 4'' to be flush with the bottom of deck board.
  • Page 21 ProJect 512 Fig.13 2-1/2'' screws per joint J. Install Upper Rail Boards 1. Install upper 2’’ x 4’’ rail boards as shown in (Fig 13). Flush with the top of 4’’ x 4’’ deck supports. 2-1/2'' screw...
  • Page 22 ProJect 512 Tip: Flex brackets to make installation of Fig.15a 4'' x 4'' easier Fig. 15 Approx. 1/4'' Fig.14 2'' Lag screw Allow 4'' x 4'' to overhang 1'' 2'' Lag Screws K. Install 4x4s 1. Work (2) 4'' x 4'' into brackets as shown in (Fig. 14), (Fig 15). 2.
  • Page 23 ProJect 512 Fig.16 2-1/2'' Deck Screws (2 per joint) Center 5/4'' x 6'' boards over Shelf-loc. Install one 2-1/2'' Deck Screw on either side to avoid hitting bracket. 2-1/2'' screw L. Install Deck Boards 1. Install 5/4'' deck boards to structure as shown (Fig. 16). 2.
  • Page 24 ProJect 512 Fig.17 2-1/2'' Deck Screws (3 per joint) 2-1/2'' Screws FIG. 17A UNDER DECK VIEW 2'' screw 2-1/2'' screw 2'' Deck Screws M. Install supports 1. Install 4'' x 4''from above and bellow as shown in (Fig 17) 2. Install 2'' x 4'' as shown in (Fig17a) Fig.17a...
  • Page 25 ProJect 512 Fig.18 2-1/2'' Screws (2 per joint) 2-1/2'' screw M. Install supports cont. 1. Install 2'' x 4'' as shown in (Fig 18)
  • Page 26 ProJect 512 Fig.19 2-1/2'' Screws 36'' 2-1/2'' screw M. Install supports cont. 1. Install 2'' x 4'' as shown in (Fig 19)
  • Page 27 ProJect 512 Fig.20 2-1/2'' Screws NOTE: Make 2'' x 4'' flush with top of Wrap Loc 2-1/2'' screw M. Install supports cont. 1. Install 2'' x 4'' as shown in (Fig 20).
  • Page 28 ProJect 512 Tip: Flex brackets to make installation of 4'' x 4'' easier Fig. 22a Fig. 22 Approx. 1/4'' Fig.21 2'' Lag screw O. Install 4x4s 1. Work (1) 4'' x 4'' into brackets as shown in (Fig. 22), (Fig 21). 2.
  • Page 29 ProJect 512 Optional Laminated Beam Fig. 23 note: Lay the lumber on a flat surface before beginning laminated beam assembly. 24" note: Attach one end of the beam with one 2-1/2'' screws, screw boards and attach the other end with three 2-1/2'' screws. This will insure that your boards will stay aligned throughout the remainder of the beam assembly.

  • Page 30: Top View

    ProJect 512 Fig. 24 Q. Swing Beam Drill Locations 1. Use a 3/8'' drill bit to drill a 3/8’’ hole through the beam at each location shown in (Fig. 24) 2. Install Swing Hangers onto swing beam at locations shown. Note: Swing Hangers must be installed on same side dimensions were originally marked.
  • Page 31 ProJect 512 Hammer Fig. 25 3/8'' hole t-nut T-nut correct! Bottom Beam Clamp (4) 1-1/4'' screws Use Screwdriver to aid in tightening Swing Hanger 1-1/4'' Wood Screw Swing Hanger ssembly 1. Tap T-nut into 3/8’’ hole as shown in Step 1. 2.
  • Page 32 ProJect 512 -Frame ssembly Fig. 26 Fig. XX 1. layout 4'' x 4’’s as shown (8) 2-1/2’’ Screws in (Fig. 26) 2. Allign EZ Frame Bracket with face of 4’’ x 4’’s. 3. Secure EZ Frame Bracket with (8) 2-1/2’’ screws to 4'' x 4''s making sure they are flush with each other.
  • Page 33 ProJect 512 Fig. 27 T-nut Washer 2-1/2'' screws 5-1/2’’ Hex Bolt 2-1/2'' screw -Frame ssembly cont. 1. Tap T--nut into 3/8’’ hole as shown in (Fig. 27) Note: If using Laminated Swing Beam, make sure T-nut teeth do not fall between seams of 2'' x 6''s. 2.
  • Page 34 ProJect 512 -Frame ssembly cont. Fig. 28 1. Position Split-Brackets on 4'' x 4'' x 56'' (Fig 28). 2. With the help of others, lift A-Frame and Swing Beam Assembly and center onto unit as shown in (Fig. 28) 3. Secure as shown in (Fig 28a). Fig.
  • Page 35 ProJect 512 Fig. 29...
  • Page 36 ProJect 512 Fig.30 Use 2-1/2'' screws to secure to 5/4'' x 6'' to 4'' x 4'' 2'' Deck Screws (2 per joint) 2'' screw 2-1/2'' screw V. Barrier Boards 1. Install 5/4'' barrier boards evenly spaced in the opening.
  • Page 37 ProJect 512 Fig.31 2'' Deck Screws (2 per joint) Fig.32 2'' screw 2-1/2'' screw 2'' Deck Screws V. Barrier Boards cont. (2 per joint) 1. Install 5/4'' and 2'' x 4'' barrier boards as shown 2-1/2'' Deck Screws (2 per joint on 2'' x 4''s) in (Fig.
  • Page 38 ProJect 512 Fig.33 2-1/2'' Deck Screws (3 per joint) 1-1/2'' Fig.33a W. Support Boards. 1. Constuct 2'' x 4''s as shown in (Fig 33) & (Fig. 33a) 2-1/2'' Deck Screws (3 per joint) 2-1/2'' Deck Screws (2 per joint) 2-1/2'' screw...
  • Page 39 ProJect 512 Fig.34 (4) 5/4'' x 6'' x 40-3/4'' 2'' Deck Screws (2 per joint) Fig.34a X. Rail Boards. 1. Install 5/4'' boards evenly (5) 5/4'' x 6'' x 36'' spaced in the opening as shown in (Fig 34) & (Fig 34a). 2'' Deck Screws (2 per joint) 2'' screw...
  • Page 40 ProJect 512 sIDe oPenInG oPtIon 1...

  • Page 41: Side Opening

    ProJect 512 sIDe oPenInG oPtIon 1 Fig. 36 EX AMPLE OF LA D D ER RU N G IN STA L LAT I O N 1-1/4'' screws • BOTTOM OF LADDER RAIL • O. Ladder ssembly. 1. On ladder rails, mark all measurement locations for each side with a pencil.
  • Page 42 ProJect 512 2-1/2'' Deck Screws (2 per joint) Fig. 39 2-1/2'' screw 2-1/2'' Deck Screws (3 per joint) Y. Install Tarp. 1. Install tarp as shown in (Fig. 39) 2. Secure tarp in six locations (Fig 39a). Fig. 39a 1-1/4'' screw...
  • Page 43 ProJect 512 Fig. 40 Fig. 41 washer 9" 1 - 3/4 Panhead screw Deck Surface InstAll PlAy HAnDles Here 1'' truss screw use truss head screws to to secure slide to deck. BB. Slide/Safety Handle Installation. THIS PRODUCT IS INTENDED FOR USE BY CHILDREN FROM 1.
  • Page 44 ProJect 512 Anchor-It (optional, sold separately) Fig. 42 Flat Washer metal strap 1-1/2" lag bolt Anchor-It stake nchor-It Installation (optional). Instructions for nchoring Swing•N•Slide ctivity Centers 1. Determine the final location of your activity center. 2. Place the Anchor-It stakes adjacent to the base and near the corners of your activity center (at the bottom of the legs on swing sets) and twist the auger-style stakes into the ground until only the loop is exposed.
  • Page 45 ProJect 512 Fig. 43 2-1/2'' Deck Screws (3 per joint) 30 1/4'' 2-1/2'' screw Swing Guard 1. Install 5/4'' x 6'' Swing Guard as shown in (Fig. 43).
  • Page 46 ProJect 512 Fig. 44a Fig. 44 2-1/2'' screws (Per joint) 2-1/2'' screws (Underneath) 2-1/2'' screws 20-1/2'' (Per joint) 2-1/2'' screw NOTE: Fig. 44b 5' Climbing Rock Wall will require 12 Climbing Rocks (2) Bags of Climbing Rocks. NE 4543S Climbing Wall Cut List. (1) 2'' x 4'' x 8'---------(1) 2'' x 4'' x 59'' (1) 2'' x 4'' x 19'' (1) 2'' x 4'' x 10'-------(2) 2'' x 4'' x 60''...
  • Page 47 ProJect 512 Climbing Rock Climbing Rock Fig. 45 (2)"T" nuts 3/8" Holes (2) 2'' Hex Head Bolts Hold (rock) (1) Loc Washer per bolt (1) Flat Washer per bolt Climbing Rock Installation 1. Mark locations of Climbing Rocks on the Climbing Wall in a pattern that will easily allow your child to climb to the deck.
  • Page 48 Questions???... Call our Customer Service Department at 1-800-888-1232 © PlayCore Inc. 2012 Printed In USA LA 5820...
  • Page 49 Set Dim. 20'W x 17'L x 13'H Est. Building Time: 5-10 hr. check out http://www.swing-n-slide.com/planupdates.htm for updates to these instructions. ASSEMBLY INSTRUCTIONS Swing•N•Slide • 1212 Barberry Drive • Janesville, Wisconsin 53545 Visit our web site at: www.swing-n-slide.com or call us at 1-800-888-1232...
  • Page 50 When the equipment is taken out of service, it must be disassembled and disposed of in such a way that no unreasonable hazards will exist at the time the set is discarded. Important! Additional Safety Instructions for all Swing-N-Slide Playgr ound Equipment. Save this instruction sheet in the event the manufactur er needs to be contacted.
  • Page 51 SAFETY INSTRUCTIONS INSTRUCCIONES DE SEGURIDAD IMPORTANT! INSTRUCTIONS CONCERNANT LA SÉCURITÉ This product is intended for single family residential use only and not intended for use in any public setting. Placement in any public setting constitutes a misuse of this product. REQUIRED SAFETY INSTALLATION INSTRUCTIONS •...

  • Page 52: Tools Required

    PROJECT 513 TOOLS REQUIRED HAMMER CIRCULAR SAW 1/2" SOCKET & WRENCH ELECTRIC DRILL SAFETY GLASSES CARPENTER'S SQUARE PHILLIPS BIT 3/8" DRILL BIT (6'' Min.) TAPE MEASURE & DUST MASK (2) 1/2'' panhead screws (4) 1'' Truss Screws (18) 5/16'' flat washers (6) T- nuts (8) 1-3/4'' panhead screws (111) 2"...
  • Page 53 Use ONLY BLACK (4) Climbing Rocks 1212 Barberry Drive PROCESS with Hardware Janesville, WI 53545 1-800-888-1232 www.swing-n-slide.com PANTONE "NEWCO RED" (1) Multicolor Tarp (1) Name Plate (4) Swing Hangers (4) Safety Handles (2) Swing Seats weight limit: 115 lbs. Kodiak...
  • Page 54 PROJECT 513 PROJECT 513 CUTTING LIST BOARD LIST OPTIONAL LADDER (16)-2'' x 4'' x 96'' (1)-2'' x 4'' x 96'' (1)-2'' x 4'' x 120'' (2)-2'' x 4'' x 120'' (17)-5/4'' x 6'' x 120'' (14)-5/4'' x 6'' x 144'' OPTIONAL ROCK WALL (6)-4'' x 4'' x 96'' (4)-4'' x 4'' x 120''...
  • Page 55 PROJECT 513 (2) 2'' x 4'' x 96'' 52-1/2'' 30'' 30'' (1) 2'' x 4'' x 120'' 41'' 36-3/4'' 24-1/2'' (2) 5/4'' x 6'' x 120'' 57'' 57'' (5) 5/4'' x 6'' x 120'' 96'' (2) 5/4'' x 6'' x 120'' 54'' 54'' (8) 5/4'' x 6'' x 120''...
  • Page 56 PROJECT 513 How to select the correct fastener Use these 3 pictorial guides to help select the correct fastener(s) for the lumber attachment you are making. Each diagram will highlight the correct number of fasteners to use, and where to attach them. 5/4'' x 6'' to 4'' x 4'' 2-1/2'' screws Apply the 2-1/2"...
  • Page 57 PROJECT 513 Understanding how the Bracket System Works Example of a Shelf-Loc bracket connection. Shelf-Loc Bracket CORRECT! Wrap-Loc WRONG! Brackets ''clipped'' brackets NOT interlocked! Example of a Shelf-Loc bracket connection. Look for ''TOP'' stamp on bracket for correct orientation. Top of bracket Introduction to the Bracket system Wrap-Loc 1.
  • Page 58 PROJECT 513 4'' x 4'' x 96'' Fig.1 Frame 1 Construction Look for ‘’TOP’’ Use a 2’’ lag screw 2'' lag screws stamp on brackets to hold bracket in while installing. per bracket place for later use. 86'' 47'' 47'' A.
  • Page 59 PROJECT 513 •WARNING• Avoid splitting your lumber by offsetting your screws at least 3/4’’ from edge. Frame 1 Construction Fig.1a 2-1/2'' screws 50-1/2'' Double check to make sure structure is square (1) 2'' lag screw (4) 2-1/2'' screws A. Frame 1 Construction cont. 2'' Lag screw 2.
  • Page 60 PROJECT 513 Frame 2 Construction Fig.2 4'' x 4'' x 120'' 2'' lag screws per bracket Look for ‘’TOP’’ Use a 2’’ lag screw stamp on brackets to hold bracket in while installing. place for later use. 59'' B. Frame 2 Construction 59'' 47'' 1.
  • Page 61 PROJECT 513 Fig.2a Frame 2 Construction 2-1/2'' screws 1-1/2'' Double check to make sure structure is square 117'' 96'' 54-1/2'' (1) 2'' lag screw (4) 2-1/2'' screws B. Frame 2 Construction cont. 2-1/2'' screw 2. Attach upper 2'' x 4'' and lower 5/4'' boards as shown in (Fig.
  • Page 62 PROJECT 513 Frame 3 Construction Fig.3 Look for ‘’TOP’’ Use a 2’’ lag screw stamp on brackets to hold bracket in while installing. 4'' x 4'' x 120'' place for later use. 2'' lag screws per bracket 59'' 47'' 59'' 47'' C.
  • Page 63 PROJECT 513 Fig.3a Frame 3 Construction 2-1/2'' screws Double check to make sure structure is square 117'' 62-1/2'' (1) 2'' lag screw (4) 2-1/2'' screws C. Frame 3 Construction cont. 2'' Lag screw 2. Attach upper 2'' x 4'' and lower 5/4'' boards as shown in (Fig.
  • Page 64 PROJECT 513 Fig.4 2-1/2'' screws 78'' (1) 2'' lag screw (4) 2-1/2'' screws D. Frame Construction 1.Install 2’’ x 4’’ and 5/4'' boards as shown above. 2'' Lag screw 2-1/2'' screw...
  • Page 65 PROJECT 513 Fig.4a Double check to make sure structure is square 2-1/2'' screws (1) 2'' lag screw (4) 2-1/2'' screws D. Frame Construction cont. 1. Attach Frame Two as shown above. 2'' Lag screw 2-1/2'' screw...
  • Page 66 PROJECT 513 Tip: Flex brackets to make installation of 4'' x 4'' easier Fig.5 Fig. 5a Approx. 1/4'' 2'' Lag Screws F. Install 4x4s 1. Work (2) 4'' x 4'' into brackets as shown in(Fig. 5), (Fig 5a). 2. Secure brackets (Fig. 5b). 2'' Lag screw Fig.5b...
  • Page 67 PROJECT 513 Fig.6 Double check to make sure structure is square (4) 2'' Lag Screws (4) 2-1/2'' screws (1) 2'' lag screw (Per joint) F. Attach Frame 3. 1. Attach and secure Frame 3 to rest of unit as shown above. 2'' Lag screw 2-1/2'' screw...
  • Page 68 PROJECT 513 Fig.7 2-1/2'' screws 2-1/2'' screw G. Install Deck Boards 1. Install 5/4'' deck boards to structure as shown (Fig. 7). 2. Use two 2-1/2'' screws at each end of deck boards. Note: On End Boards, avoid screwing into Shelf Brackets by placing screws behind Shelf Bracket location.
  • Page 69 PROJECT 513 Fig.8 B o t t o m V i e w Fig.8b 2-1/2'' screws per joint Fig.8a (16) 2-1/2'' screws 2-1/2'' screw H. Lower Deck Support Board 1. Construct support boards as shown in (Fig. 8). 2. Secure center of floor boards as shown in (Fig 8a) 3.
  • Page 70 PROJECT 513 Fig.8c 2-1/2'' screws 2-1/2'' screws 2-1/2'' screw I. Install Lower Rail Board 1. Install lower 2'' x 4'' rail board as shown in (Fig 8c). Flush with the sides of 4'' x 4'' deck supports.
  • Page 71 PROJECT 513 Fig.9 2-1/2'' screws 2-1/2'' screws K. Install Shelf-Loc brackets 2-1/2'' screw 1. Install 2x4 boards as shown in (Fig.9).
  • Page 72 PROJECT 513 Tip: Flex brackets to make installation of 4'' x 4'' easier Fig.10a Fig.10b Approx. 1/4'' Fig.10 2'' Lag screw K. Install 4x4s cont. 1. Work (2) 4'' x 4'' into brackets as shown in (Fig. 10a), (Fig 10). 2.
  • Page 73 PROJECT 513 Fig.11 MAKE BOARDS FLUSH WITH 2-1/2'' Deck Screws (2 per joint) 4'' x 4'' SUPPORT 2-1/2'' screw L. Install Deck Boards 1. Install 5/4'' deck boards to structure as shown (Fig. 11). 2. Use two 2-1/2'' screws at each end of deck boards. Where shelf bracket blocks screw path, center board and place one screw on either side.
  • Page 74 PROJECT 513 Fig.12 Fig.12a Fig.12b (16) 2-1/2'' screws 2-1/2'' screw M. Install Upper Rail Boards 1. Install under deck support as shown in (Fig 12). Flush with the edges of 5/4’’ x 6’’ deck supports. 2. Hold Deck Support Board from below until secured in place from above as shown in (Fig.
  • Page 75 PROJECT 513 Fig.13 2-1/2'' Screws 2-1/2'' Screws per board 2-1/2'' Screws 2-1/2'' screw N. Install supports cont. 1. Install 2'' x 4'' as shown in (Fig 13)
  • Page 76 PROJECT 513 Fig.14 Tip: Flex brackets to make installation of 4'' x 4'' easier Fig. 15 Approx. 1/4'' 2'' Lag Screws Fig.16 O. Install accessory 4x4 1. Work (1) 4'' x 4'' into brackets as shown in (Fig. 14), (Fig 15). 2.
  • Page 77 PROJECT 513 Optional Laminated Beam NOTE: Lay the lumber on a flat surface before beginning laminated beam assembly. Fig. 17 24" NOTE: Attach one end of the beam with three 2-1/2'' screws. Secure boards and attach the other end with three 2-1/2'' screws. This will insure that your boards will stay aligned throughout the remainder of the beam assembly.

  • Page 78: Top View

    PROJECT 513 Fig. 18 Q. Swing Beam Drill Locations 1. Use a 3/8'' drill bit to drill a 3/8’’ hole through the beam at each location shown in (Fig. 18) 2. Install Swing Hangers onto swing beam at locations shown. Note: Swing Hangers must be installed on same side dimensions were originally marked.
  • Page 79 PROJECT 513 Fig. 19 Hammer 3/8'' hole T-nut t-nut Bottom Beam Clamp (4) 1-1/4'' screws Use Screwdriver to aid in tightening Swing Hanger Q. Swing Beam Drill Locations 1. Tap t-nut into 3/8’’ hole as shown in (Fig. 19) 2. Place a bottom beam clamp over the swing hanger as shown in (Fig. 19) 3.

  • Page 80: A-Frame Assembly

    PROJECT 513 Fig. 20 (8) 2-1/2 Screws R. A-Frame Assembly 1. layout 4'' x 4’’s as shown in (Fig. 20) 2. Align EZ Frame Bracket with face of 4'' x 4''s. 3. Secure EZ Frame Bracket with (8) 2-1/2'' screws to 4'' x 4''s making sure they are flush with each other.
  • Page 81 PROJECT 513 Fig. 22 T-nut Washer 2-1/2'' screws 5-1/2 Hex Bolt 2-1/2'' screw S. A-Frame Assembly cont. 1. 1. Tap T-nut into 3/8’’ hole as shown in (Fig. 22) Note: If using Laminated Swing Beam, make sure T-nut teeth do not fall between seams of 2'' x 6''s. 2.
  • Page 82 PROJECT 513 Fig. 23 T. A-Frame Assembly cont. 1. Position Split-Brackets on 4'' x 4'' x 48'' (Fig 23). 2. With the help of others, lift A-Frame and Swing Beam Assembly and center onto unit as shown in (Fig. 23) 3.
  • Page 83 PROJECT 513 Fig.25 2-1/2'' Deck 2'' Deck Screws Screws (2 per joint) per joint 2'' Deck Screws (2 per joint) (2) 2'' x 4’’ x 30'' 1-1/2 Gap 1-1/2 Gap Fig.25a (1) 5/4'' x 6’’ x 22-1/2'' 2'' Deck Screws (2 per joint) V.
  • Page 84 PROJECT 513 Fig.26 2'' Deck Screws (2 per joint) 2'' Deck Screws (2 per joint) Fig.26a 2'' Deck Screws (2 per joint) V. Barrier Boards cont. 1. Install 5/4'' barrier boards evenly 1-1/2 Gap spaced in the opening. 1-1/2 Gap 2-1/2'' Deck Screws (2 per joint on 2'' x 4''s) 2'' screw...
  • Page 85 PROJECT 513 Fig.27 Fig.27a 2'' x 4'' x 16'' 2-1/2'' Deck Screws (per joint) 2-1/2'' Deck Screws (per joint) 1-1/2'' Overhang 1-1/2'' Overhang W. Roof Construction. 1. Constuct Wood Roof Frame as shown in (Fig 27) and (Fig. 27a). Fig.28 2-1/2'' Deck Screws (per joint) W.
  • Page 86 PROJECT 513 Fig.29 2-1/2'' Deck Screws (2 per joint) (6) 5/4'' x 6'' x 54'' Fig.30 (6) 5/4'' x 6'' x 54'' 2-1/2'' Deck Screws (2 per joint) X Roof Construction cont. 3. Install 5/4'' x 6''s as shown in (Fig 29) and (Fig.
  • Page 87 PROJECT 513 Fig.30a Fig.30b (1) 5/4'' x 6'' x 33'' (1) 5/4'' x 6'' x 36-3/4'' 2'' Deck Screws (2 per joint) 2'' Deck Screws (2 per joint) X Support Boards cont. 1. Install 5/4'' x 6'' Roof Supports as shown in (Fig 30a) and (Fig 30b).
  • Page 88 PROJECT 513 SIDE OPENING OPTION 1...
  • Page 89 PROJECT 513 SIDE OPENING OPTION 1 2-1/2'' EXA M P LE OF LA D D ER R UNG I NSTA L LAT I O N 1-1/4'' screws Fig. 32 O. Ladder Assembly. • BOTTOM OF LADDER RAIL • 1. On ladder rails, mark all measurement locations for each side with a pencil.
  • Page 90 PROJECT 513 Fig. 35 2-1/2'' Deck Screws (3 Per joint) 19'' 2-1/2'' screw Z1. Install Protective Barrier Board 1. Secure protective 5/4'' barrier board as shown in (Fig 35).
  • Page 91 2. Install Slide as shown in (Fig. 37) Janesville, WI 53545 1-800-888-1232 Important: Secure your product ID tag onto easy to read location of any 4'' x 4'' Do not use hardware provided using (2) 2'' screws with slide. Use Truss head screws .swing-n-slide.com included with Kit.
  • Page 92 PROJECT 513 Anchor-It (Sold Seperately) Fig. 38 Flat Washer metal strap 1-1/2" lag bolt Anchor-It stake S. Anchor-It Installation (optional). I I n n s s t t r r u u c c t t i i o o n n s s f f o o r r A A n n c c h h o o r r i i n n g g S S w w i i n n g g • • N N • • S S l l i i d d e e A A c c t t i i v v i i t t y y C C e e n n t t e e r r s s 1.
  • Page 93 PROJECT 513 SIDE OPENING OPTION 2 Fig. 40 Fig. 39 2-1/2'' Deck Screws 2-1/2'' screws (2 Per joint) (Per joint) 2-1/2'' screw Fig. 40a N N O O T T E E : : 4' Climbing Rock Wall will require M M i i n n .
  • Page 94 PROJECT 513 Climbing Rock Climbing Rock Fig. 41 (2)"T" nuts 3/8" Holes (2) 2'' Hex Head Bolts Hold (rock) (1) Loc Washer per bolt (1) Flat Washer per bolt Climbing Rock Installation 1. Mark locations of Climbing Rocks on the Climbing Wall in a pattern that will easily allow your child to climb to the deck.
  • Page 95 PROJECT 513...
  • Page 96 Questions???... Call our Customer Service Department at 1-800-888-1232 © PlayCore Inc. 2007 Printed In USA LA 5821...
  • Page 97 Temps de construction estimé : 5 à 10 heures check out http://www.swing-n-slide.com/planupdates.htm for updates to these instructions. INSTRUCCIONES DE MONTAJE INSTRUCTIONS D’ASSEMBLAGE Swing•N•Slide • 1212 Barberry Drive • Janesville, Wisconsin 53545 Visit our web site at: www.swing-n-slide.com or call us at 1-800-888-1232...

  • Page 98: Seguridad Durante La Operación

    Cuando el equipo sea retirado de servicio, se debe desarmar y desechar de tal manera que no se presenten peligros no razonables en el momento de desecharlo. ¡Importante! Instrucciones de seguridad adicionales para todos los equipos de juego Swing-N-Slide. Guardar esta hoja de instrucciones en caso de que se r equiera contactar al fabricante.

  • Page 99: Fiche De Contrôle Des Mesures De Sécurité Pour Les Accessoires Swing-N-Slide

    Fiche de contrôle des mesures de sécurité pour les accessoires Swing-N-Slide L’observation des déclarations et des avertissements suivants réduit les risques de blessur es graves ou mortelles Installation sécuritaire – Avez-vous : Consulté les instructions d’assemblage fournies avec l’unité de jeu? Noté...
  • Page 100 SAFETY INSTRUCTIONS INSTRUCCIONES DE SEGURIDAD INSTRUCTIONS CONCERNANT LA SÉCURITÉ IMPORTANT! This product is intended for single family residential use only and not intended for use in any public setting. Placement in any public setting constitutes a misuse of this product. REQUIRED SAFETY INSTALLATION INSTRUCTIONS •...
  • Page 101 HERRAMIENTAS NECESARIAS/OUTILS REQUIS SIERRA CIRCULAR MARTILLO TALADRO ELÉCTRICO DADO Y LLAVE DE 1/2" (1.2 cm) SCIE CIRCULAIRE MARTEAU PERCEUSE ÉLECTRIQUE CLÉ ET DOUILLE DE 1/2 po (12 mm) GAFAS DE SEGURIDAD BROCA DE TALADRO DE 3/8" (0.95 cm) BROCA DE ESTRELLA ESCUADRA DE CARPINTERO CINTA MÉTRICA Y MÁSCARA ANTIPOLVO...
  • Page 102 BLACK (4) piedras para escalar con piezas 1212 Barberry Drive PROCESS Janesville, WI 53545 (4) Prises d’escalade avec quincaillerie 1-800-888-1232 www.swing-n-slide.com PANTONE "NEWCO RED" (1) Cubierta (1) Toit (1) placa del nombre (1) Plaque d’identification (4) Colgaderos de columpio (4) Supports de balançoire...
  • Page 103 PROYECTO 513/PROJET 513 PROYECTO 513/PROJET 513 BOARD LIST OPTIONAL LADDER (16)-2'' x 4'' x 96'' (1)-2'' x 4'' x 96'' (1)-2'' x 4'' x 120'' (2)-2'' x 4'' x 120'' (17)-5/4'' x 6'' x 120'' (14)-5/4'' x 6'' x 144'' OPTIONAL ROCK WALL (6)-4'' x 4'' x 96'' (4)-4'' x 4'' x 120''...
  • Page 104 PROYECTO 513/PROJET 513 (2) 2'' x 4'' x 96'' 52-1/2'' 30'' 30'' (1) 2'' x 4'' x 120'' 41'' 36-3/4'' 24-1/2'' (2) 5/4'' x 6'' x 120'' 57'' 57'' (5) 5/4'' x 6'' x 120'' 96'' (2) 5/4'' x 6'' x 120'' 54'' 54'' (8) 5/4'' x 6'' x 120''...
  • Page 105 PROYECTO 513/PROJET 513 Cómo seleccionar el sujetador apropiado Comment choisir le bon système d'attache Utilice estas tres guías ilustradas para seleccionar el (los) sujetador(es) apropiado(s) para el ajuste de maderas que usted está haciendo. Cada diagrama resaltará el número correcto de sujetadores que debe usarse, y dónde fijarlos. Utilisez ces 3 guides illustrés pour faciliter le choix du ou des système(s) d'attache(s) pour l'assemblage de pièces de bois concernées.
  • Page 106 PROYECTO 513/PROJET 513 Cómo funciona el sistema de abrazaderas Comprendre le fonctionnement du système de fixation abrazadera de estante Ejemplo de una conexión con abrazadera de estante. Connecteur « Shelf-Loc » Exemple de connecteur « Shelf-Loc ». ¡CORRECTO!/BONNE MÉTHODE! abrazadera de envoltura Connecteur Wrap-Loc ¡INCORRECTO!/MAUVAISE MÉTHODE! abrazaderas entrelazadas...

  • Page 107: Table Des Matières

    PROYECTO 513/PROJET 513 4" x 4" x 96" Construcción del marco 1 Fig. 1 Construction du cadre 1 Busque la marca Use a 2’’ lag screw ‘’TOP’’ sobre las abrazaderas cuando esté realizando la instalación. to hold bracket in tornillos de compresión Recherchez l'estampille «...
  • Page 108 PROYECTO 513/PROJET 513 •ADVERTENCIA• Evite rajar la madera colocando los tornillos a una distancia de al menos 3/4" desde el bor de. •AVERTISSEMENT!• Évitez de fendre votre pièce de bois en décalant vos vis à au moins 3/4" du r ebord. Construcción del marco 1/Construction du cadre 1 tornillos de 2 1/2"...

  • Page 109: Fig. 2

    PROYECTO 513/PROJET 513 Construcción del marco 2/Construction du cadre 2 Fig. 2 4" x 4" x 120" tornillos de compresión de 2" por abrazadera Deux (2) Vis tire-fond de 2" par fixation Busque la marca Use a 2’’ lag screw ‘’TOP’’...

  • Page 110: Tornillo De 2 1/2

    PROYECTO 513/PROJET 513 Construcción del marco 2/Construction du cadre 2 Fig. 2a tornillos de 2 1/2" Trois (3) Vis de 2 1/2" 1-1/2" Verifique dos veces para asegurarse de que la estructura esté cuadrada 117" Vérifiez bien que la structure est d'équerre 96"...
  • Page 111 PROYECTO 513/PROJET 513 Construcción del marco 3 Construction du cadre 3 Fig. 3 Busque la marca Use a 2’’ lag screw ‘’TOP’’ sobre las abrazaderas cuando esté realizando la instalación. to hold bracket in Recherchez l'estampille « TOP » (dessus) sur les fixations place for later use.

  • Page 112: Construcción Del Marco 3

    PROYECTO 513/PROJET 513 Construcción del marco 3 Fig. 3a Construction du cadre 3 2-1/2" screws Verifique dos veces para asegurarse de que la estructura esté cuadrada 117" Vérifiez bien que la structure est d'équerre 62-1/2" (1) tornillo de compresión de 2" (4) tornillos de 2 1/2"...

  • Page 113: Construcción Del Marco

    PROYECTO 513/PROJET 513 Fig. 4 tornillos de 2 1/2" Trois (3) Vis de 2 1/2" 78" (1) tornillo de compresión de 2" (4) tornillos de 2 1/2" Une (1) vis tire-fond de 2" Quatre (4) vis de 2 1/2" D. Construcción del marco 1.
  • Page 114 PROYECTO 513/PROJET 513 Fig. 4a Verifique dos veces para asegurarse de que la estructura esté cuadrada Vérifiez bien que la structure est d'équerre Tornillos de 2 1/2" Trois (3) Vis de 2 1/2" (1) tornillo de compresión de 2" (4) tornillos de 2 1/2" Une (1) vis tire-fond de 2"...
  • Page 115 PROYECTO 513/PROJET 513 Consejo: Doble las abrazaderas para facilitar la instalación de la pieza de 4" x 4" Conseil : utilisez les fixations flexibles pour faciliter l'installation des poutres de 4" x 4" Fig. 5 Fig. 5a Aprox. 1/4" Approx. 1/4" Tornillos de compresión de 2"...
  • Page 116 PROYECTO 513/PROJET 513 Fig. 6 Verifique dos veces para asegurarse de que la estructura esté cuadrada Vérifiez bien que la structure est d'équerre (4) tornillos de compresión de 2" Quatre (4) vis tire-fond 2" (4) tornillos de 2 1/2" (1) tornillo de compresión de 2" (Por junta) Quatre (4) vis 2 1/2"...
  • Page 117 PROYECTO 513/PROJET 513 Fig. 7 tornillos de 2 1/2" Vis de 2 1/2 Tornillo de 2 1/2" Vis de 2 1/2" G. Instale las tablas de la plataforma 1. Instale las tablas de 5/4" de la plataforma a la estructura como se muestra en la (Fig. 7). 2.
  • Page 118 PROYECTO 513/PROJET 513 Fig. 8 V i s t a s u p e r i o r V u e d e s s o u s Fig. 8b tornillos de 2 1/2" por junta Vis de 2 1/2" par joint Fig.
  • Page 119 PROYECTO 513/PROJET 513 Fig. 8c tornillos de 2 1/2" Vis de 2 1/2" tornillos de 2 1/2" Vis de 2 1/2" I. Instale el tornillo de 2 1/2" de la tabla del riel inferior 1. Instale la tabla de 2" x 4" del riel inferior como se muestra en la (Fig. 8c). Tornillo de 2 1/2"...
  • Page 120 PROYECTO 513/PROJET 513 Fig. 9 tornillos de 2 1/2" Vis de 2 1/2" tornillos de 2 1/2" Vis de 2 1/2" K. Instale las abrazaderas de estante 1. Instale las tablas de 2'' x 4'' como se muestra en la (Fig. 9). Tornillo de 2 1/2"...
  • Page 121 PROYECTO 513/PROJET 513 Consejo: Doble las abrazaderas para facilitar la instalación de la pieza de 4" x 4" Conseil : utilisez les fixations flexibles pour faciliter l'installation des poutres de 4" x 4" Fig. 10a Fig. 10b Aprox. 1/4" Approx. 1/4" Fig.
  • Page 122 PROYECTO 513/PROJET 513 Fig. 11 ALINEE LAS TABLAS CON EL SOPORTE DE 4" x 4" Tornillos de plataforma de 2 1/2" (2 por junta) ASSUREZ-VOUS Deux (2) D'AFFLEURER LES Vis de terrasse de 2 1/2" (2 par joint) PLANCHES AVEC LA FIXATION DE 4"...
  • Page 123 PROYECTO 513/PROJET 513 Fig. 12 Fig. 12a Fig. 12b (16). tornillos de 2 1/2" Seize (16) Vis de 2 1/2" Tornillo de 2 1/2" Vis de 2 1/2" M. Instale las tablas de los rieles superiores 1. Instale el soporte inferior de la plataforma como se muestra en la (Fig. 12). Alinee con los bordes de los soportes de plataforma de 5/4"...
  • Page 124 PROYECTO 513/PROJET 513 Fig. 13 tornillos de 2 1/2" Trois (3) Vis de 2 1/2" tornillos de 2 1/2" por tabla Cinq (5) Vis de 2 1/2" par planche tornillos de 2 1/2" Vis de 2 1/2" Tornillo de 2 1/2" Vis de 2 1/2"...
  • Page 125 PROYECTO 513/PROJET 513 Fig. 14 Consejo: Doble las abrazaderas para facilitar la instalación de la pieza de 4" x 4" Conseil : utilisez les fixations flexibles pour faciliter l'installation des poutres de 4" x 4" Fig. 15 Aprox. 1/4" Approx. 1/4" tornillos de compresión de 2"...

  • Page 126: Viga Laminada Opcional/Poutre Laminée En Option

    PROYECTO 513/PROJET 513 Viga laminada opcional/Poutre laminée en option NOTA: Disponga la madera sobre una superficie plana antes de iniciar el ensamblaje de la viga laminada. REMARQUE : déposez les pièces de bois d' ceuvre sur une surface horizontale avant de commencer l'assemblage de la poutre laminée. Fig.

  • Page 127: Vista Superior Vue Du Dessus

    PROYECTO 513/PROJET 513 Ubicación de perforación de 3/8" Fig. 18 Emplacement des trous de 3/8" fait avec une perceuse Q. Ubicación de las perforaciones de la viga del columpio 1. Utilice una broca de 3/8" para hacer una perforación de 3/8" a través de la viga en cada lugar que se muestra en la (Fig.
  • Page 128 PROYECTO 513/PROJET 513 Fig. 19 Martillo Marteau Orificio de 3/8'' Trou de 3/8'' Tuerca en T Écrou en T encastré Abrazadera de la viga inferior Attache de base de poutre (4) tornillos de 1 1/4" Quatre (4) vis de 1 1/4 " Use el destornillador para ajustar Utilisez un tournevis pour mieux serrer Colgadero del columpio Crochet de suspension de balançoire...
  • Page 129 PROYECTO 513/PROJET 513 Fig. 20 R. Disposición del montaje de la (8) tornillos de 2 1/2" Huit (8) vis 2 1/2" estructura en A 1. 4" x 4"s como se muestra en la (Fig. 20). 2. Alinee la abrazadera del marco EZ con la cara de las piezas de 4"...
  • Page 130 PROYECTO 513/PROJET 513 Fig. 22 Tuerca en T/Écrou en T encastré Arandela/Rondelle Tornillos de 2 1/2" Vis de 2 1/2" Perno de cabeza hexagonal de 5 1/2" Boulon à tête hexagonale de 5 1/2" Tornillo de 2 1/2"/ Vis de 2 1/2" S.
  • Page 131 PROYECTO 513/PROJET 513 Fig. 23 T. Montaje del marco en A (cont.) 1. Ubique los soportes divisores en la pieza de 4" x 4" x 48" (Fig. 23). 2. Con ayuda de otras personas, levante el marco en A y el conjunto de la viga del columpio y céntrelos en la unidad como se muestra en la (Fig.
  • Page 132 PROYECTO 513/PROJET 513 Fig. 25 tornillos de plataforma de Tornillos de plataforma 2 1/2" por junta de 2" (2 por junta) vis à terrasse de Vis à terrasse de 2 1/2" par joint 2" (2 par joint) Tornillos de plataforma de 2"...
  • Page 133 PROYECTO 513/PROJET 513 Tornillos de plataforma Fig. 26 de 2" (2 por junta) Vis à terrasse de 2" (2 par joint) Tornillos de plataforma de 2" (2 por junta) Vis à terrasse de 2" (2 par joint) Fig. 26a Tornillos de plataforma de 2"...
  • Page 134 PROYECTO 513/PROJET 513 Fig. 27 Fig. 27a 2" x 4" x 16" tornillos de plataforma de 2 1/2" por junta tornillos de plataforma Deux (2) de 2 1/2" por junta Vis à terrasse de 2 1/2" Trois (3) (par joint) Vis à...
  • Page 135 PROYECTO 513/PROJET 513 Fig. 29 Tornillos de plataforma de 2-1/2" (2 por junta) Vis à terrasse de 2-1/2" (2 par joint) (6) 5/4" x 6" x 54" Fig. 30 (6) 5/4" x 6" x 54" Tornillos de plataforma de 2 1/2" (2 por junta) Vis à...
  • Page 136 PROYECTO 513/PROJET 513 Fig. 30a Fig. 30b (1) 5/4" x 6" x 33" (1) 5/4" x 6" x 36-3/4" Tornillos de plataforma Tornillos de plataforma de 2" (2 por junta) de 2" (2 por junta) Vis à terrasse de Vis à terrasse de 2" 2"...
  • Page 137 PROYECTO 513/PROJET 513 OPCIÓN DE APERTURA LATERAL 1 OUVERTURE LATÉRALE OPTION 1...
  • Page 138 PROYECTO 513/PROJET 513 OPCIÓN DE APERTURA LATERAL 1 OUVERTURE LATÉRALE OPTION 1 EJEMPLO DE INSTALACIÓN DE PELDAÑOS DE LA ESCALERA 2-1/2" EXEMPLE D'INSTALLATION DES BARREAUX D'ÉCHELLE tornillos de 1-1/4" Six (6) Vis de 1-1/4" O. Ensamblaje de la escalera. 1. Sobre los rieles de la escalera, marque en cada lado con un lápiz la ubicación de todas las medidas.
  • Page 139 PROYECTO 513/PROJET 513 Fig. 35 Tornillos de plataforma de 2 1/2" (3 por junta) Neuf (9) Vis de terrasse de 2 1/2" (3 par joint) 19" Tornillo de 2 1/2" Vis de 2 1/2" Z1. Instale la tabla de la barrera de protección 1.
  • Page 140 11" au-dessus de la surface de la terrasse (Fig. 36). de 4" x 4" donde pueda leerse fácilmente 2. Installez la glissoire, comme illustré (Fig. 37). .swing-n-slide.com Important : Fixez votre étiquette d'identification du produit à un Veillez à ne pas utiliser les fixations fournies avec la glissoire.
  • Page 141 PROYECTO 513/PROJET 513 Anclaje/« Anchor-It » Fig. 38 arandela plana Rondelle plate correa metálica Courroie de métal pernos de de 1 1/2" 1 1/2" Tire-fond Anclaje « Anchor-It » Y. Instalación del anclaje. Instrucciones para anclar los centros de actividades Swing•N•Slide 1.
  • Page 142 PROYECTO 513/PROJET 513 OPCIÓN 2 DE APERTURA LATERAL/OUVERTURE LATÉRALE OPTION 2 Fig. 40 Fig. 39 Tornillos de plataforma 6" 6" de 2 1/2" (2 por junta) Vis de terrasse de 2 1/2" tornillos de 2 1/2"(Por junta) (2 par joint) Vis de terrasse de 2 1/2"...
  • Page 143 PROYECTO 513/PROJET 513 Climbing Rock Climbing Rock Fig. 41 (2) tuercas en “T” (2) Écrous en « T » (2) pernos con cabeza hexagonal de 1 1/2" agujeros de 3/8" (2) Boulons à tête Trous de 3/8" hexagonale de 1-1/2" sostén (piedra) Prise (rocher) (1) arandela de bloqueo por perno...
  • Page 144 ¿¿¿Alguna pregunta??? ... Llamar a nuestro Departamento de servicio al cliente al 1-800-888-1232 Des questions? Appelez notre service à la clientèle, au 1-800-888-1232 © PlayCore Inc. 2007 Impreso en los Estados Unidos LA 5821 Imprimé aux États-Unis...
  • Page 145 Other benefits include information on product warranties, assembly plan updates, joining our mailing list for new products and promotions, receiving our newsletter, and providing feedback on products. Swing•N•Slide • 1212 Barberry Drive • Janesville, Wisconsin 53545 Visit our web site at: www.swing-n-slide.com or call us at 1-800-888-1232...
  • Page 146 When the equipment is taken out of service, it must be disassembled and disposed of in such a way that no unreasonable hazards will exist at the time the set is discarded. Important! Additional Safety Instructions for all Swing-N-Slide Playground Equipment. Save this instruction sheet in the event the manufacturer needs to be contacted.
  • Page 147 Swing-N-Slide® will repair, or at its discretion, replace any part within the stated warranty period which is defective in workmanship or materials. This decision is subject to verification of the defect upon delivery of the defective part to Swing-N-Slide® at 1212 Barberry Drive, Janesville, Wisconsin, 53545.
  • Page 148 LA 6684 Kodiak 514_- 3/7/12 10:05 AM Page 4 PROJecT 514 KODIAK 514 PROJECT LUMBER LIST THIS LIST IS IN ADDITION TO LUMBER REQUIRED BY PROJECT 512 (4) 2'' x 4'' x 8' (1) 2'' x 4'' x 10' (2) 5/4'' x 6'' x 10' KODIAK 514 ROCK WALL LUMBER 47'' (1) 2'' x 4'' x 96''...
  • Page 149 LA 6684 Kodiak 514_- 3/7/12 10:05 AM Page 5 PROJecT 514 How to select the correct fastener Use these 3 pictorial guides to help select the correct fastener(s) for the lumber attachment you are making. Each diagram will highlight the correct number of fasteners to use, and where to attach them.
  • Page 150 LA 6684 Kodiak 514_- 3/7/12 10:05 AM Page 6 PROJecT 514 Fig. 1a Fig. 1 FLUSH 2-1/2'' screws (Per joint) 1/2'' 2'' x 4'' x 47'' 1/2'' 2-1/2'' screws (Per joint) 7-1/4'' 5-1/4'' 2-1/2'' screw NOTE: 4' Climbing Rock Wall will require Fig.
  • Page 151 LA 6684 Kodiak 514_- 3/7/12 10:05 AM Page 7 PROJecT 514 Climbing Rock Climbing Rock Fig. 2 (2)"T" nuts 3/8" Holes (2) 2'' Hex Head Bolts Hold (rock) (1) Loc Washer per bolt (1) Flat Washer per bolt Climbing Rock Installation 1.
  • Page 152 LA 6684 Kodiak 514_- 3/7/12 10:05 AM Page 8 PROJecT 514 nOTe: Fig. 3 The 5’ Turbo Tube is designed to fit on the rear barrier of the 5’ Deck on the Kodiak 514. 5' DECK HEIGHT 1-3/8'' Gap Fig. 3a Between Each 2-1/2'' screw Barrier Board...
  • Page 153 LA 6684 Kodiak 514_- 3/7/12 10:05 AM Page 9 PROJecT 514 Fig. 4 2-1/2'' screws per joint 2-1/2'' Fig. 4a screws per joint 2-1/2'' screw Slide Barrier Construction 2-1/2'' ttach the Turbo Tube Slide Support Board as screws shown in (Fig. 4). ttach 2'' x 4'' Slide Barrier Boards as shown in (Fig.
  • Page 154 LA 6684 Kodiak 514_- 3/7/12 10:05 AM Page 10 PROJecT 514 Fig. 5 2-1/2'' screws per board inSiDe View OF SliDe enTRance 2-1/2'' screw Slide Barrier Construction 1. Install interior slide barrier support boards shown in (Fig. 5). 2. Refer to the 5' Turbo Tube Slide Plan for instructions on assembling the Turbo Tube Slide and Footer ssembly.
  • Page 155 LA 6684 Kodiak 514_- 3/7/12 10:05 AM Page 11 PROJecT 514 ReFeRence The Plan PicTuReD FOR SliDe aSSembly...
  • Page 156 LA 6684 Kodiak 514_- 3/7/12 10:05 AM Page 12...

  • Page 157: Instructions D'assemblage

    Swing•N•Slide • 1212 Barberry Drive • Janesville, Wisconsin 53545 Visite nuestro sitio web en www.swing-n-slide.com o llámenos al Visitez notre site Web au www.swing-n-slide.com ou appelez-nous au 1-800-888-1232 ©...
  • Page 158 Lorsque l’équipement doit être mis hors de service, il doit être démonté et mis aux déchets de manière à limiter les risques au moment de sa mise aux déchets. ¡Importante! Instrucciones de seguridad adicionales para todos los equipos de juego Swing-N-Slide. Guardar esta hoja de instrucciones en caso de que se requiera contactar al fabricante.
  • Page 159 LA 6684 Kodiak 514FRE_SPA_- 3/7/12 10:03 AM Page 3 Este producto ha sido ideado para su uso en una residencia u hogar de una sola familia y no para usarse en lugares públicas. Su uso en lugares públicos constituye una mala utilización de este producto. ¡IMPORTANTE! INSTRUCCIONES ADICIONALES DE SEGURIDAD PARA LA INSTALACIÓN Según establece la Sociedad mericana de Pruebas y Materiales ( merican Society for Testing and Materials, STM), todos los equipos deben anclarse al suelo y, si la unidad tiene...
  • Page 160 LA 6684 Kodiak 514FRE_SPA_- 3/7/12 10:03 AM Page 4 LISTE DU BOIS D'ŒUVRE POUR LE PROJET KODIAK 514 CETTE LISTE S'AJOUTE À CELLE DU BOIS D'ŒUVRE REQUIS POUR LE PROJET 512 (4) 5,08 cm x 10,16 cm x 2,44 m (1) 5,08 cm x 10,16 cm x 3,04 m (2) 3,17 cm x 15,24 cm x 3,04 m BOIS D'ŒUVRE POUR LE MUR D'ESCALADE KODIAK 514...
  • Page 161 LA 6684 Kodiak 514FRE_SPA_- 3/7/12 10:03 AM Page 5 comment sélectionner la fixation correcte cómo elegir el sujetador correcto Utilisez les trois guides illustrés suivants pour vous aider à sélectionner la(es) fixation(s) correcte(s) pour fixer le bois d'œuvre que vous êtes en train d'installer. Chaque schéma soulignera le nombre correct de fixations à utiliser et où...
  • Page 162 LA 6684 Kodiak 514FRE_SPA_- 3/7/12 10:03 AM Page 6 PROJET 514/pROYEcTO 514 Fig. 1 Fig. 1a À ras AL RAS vis 6,35 cm (par joint) tornillos de 6,35 cm (Por junta) ESPACE d'1,27 cm ESPACIO 1,27 CM 5,08 cm x ESPACE d'1,27 cm 10,16 cm x...
  • Page 163 LA 6684 Kodiak 514FRE_SPA_- 3/7/12 10:03 AM Page 7 PROJET 514/pROYEcTO 514 Climbing Rock Climbing Rock Fig. 2 (2) tuercas en “T” (2) Écrous en « T » (2) pernos con cabeza hexagonal de 1 1/2" (2) Boulons à tête hexagonale de 1-1/2"...
  • Page 164 LA 6684 Kodiak 514FRE_SPA_- 3/7/12 10:03 AM Page 8 PROJET 514/pROYEcTO 514 Fig. 3 REmARquE : La glissade Turbo Tube de 1,52 m est conçue pour s'adapter à la barrière arrière de la plate-forme à 1,52 m de haut du Kodiak 514 nOTA: El Tobogán Turbo de Tubo de 1,52 m está...
  • Page 165 LA 6684 Kodiak 514FRE_SPA_- 3/7/12 10:03 AM Page 9 PROJET 514/pROYEcTO 514 Fig. 4 vis 6,35 cm par joint 6,35 cm' tornillos por cada junta tornillos vis 6,35 cm Fig. 4a de 6,35 cm par joint por cada junta vis 6,35 cm Tornillo de 6,35 cm Construction de la barrière de glissade 1.
  • Page 166 LA 6684 Kodiak 514FRE_SPA_- 3/7/12 10:03 AM Page 10 PROJET 514/pROYEcTO 514 Fig. 5 vis 6,35 cm tornillos de 6,35 cm por cada tabla vuE dE L'inTÉRiEuR dE L'EnTRÉE dE LA gLissAdE visTA inTERiOR dE LA EnTRAdA dEL TObOgán vis 6,35 cm Tornillo de 6,35 cm Construction de la barrière de glissade 1.
  • Page 167 LA 6684 Kodiak 514FRE_SPA_- 3/7/12 10:03 AM Page 11 PROJET 514/pROYEcTO 514 REFEREncE du pLAn pOuR LE mOnTAgE iLLusTRÉ sLidE REFEREnciA AL pLAn dE REpREsEnTAdO pOR LA AsAmbLEA sLidE...
  • Page 168 LA 6684 Kodiak 514FRE_SPA_- 3/7/12 10:03 AM Page 12 PROJET 514/pROYEcTO 514...
  • Page 169 Other benefits include information on product warranties, assembly plan updates, joining our mailing list for new products and promotions, receiving our newsletter, and providing feedback on products. Swing•N•Slide • 1212 Barberry Drive • Janesville, Wisconsin 53545 Visit our web site at: www.swing-n-slide.com or call us at 1-800-888-1232...
  • Page 170 When the equipment is taken out of service, it must be disassembled and disposed of in such a way that no unreasonable hazards will exist at the time the set is discarded. Important! Additional Safety Instructions for all Swing-N-Slide Playground Equipment. Save this instruction sheet in the event the manufacturer needs to be contacted.
  • Page 171 Swing-N-Slide® will repair, or at its discretion, replace any part within the stated warranty period which is defective in workmanship or materials. This decision is subject to verification of the defect upon delivery of the defective part to Swing-N-Slide® at 1212 Barberry Drive, Janesville, Wisconsin, 53545.
  • Page 172 Project 515 TOOLS REQUIRED HAMMer cIrcUlAr sAW 1/2" socKet & WreNcH electrIc DrIll sAFety GlAsses cArPeNter's sQUAre 3/8" DrIll bIt (6'' Min.) PHIllIPs bIt tAPe MeAsUre & DUst MAsK (2) 1/2'' panhead screws (4) 1'' Truss Screws (10) 5/16'' flat washers (6) T- nuts (8) 1-3/4'' panhead screws (4) 1/4'' flat washers...
  • Page 173 AGES 2-10 YEARS For Home / Residential Use ONLY 1212 Barberry Drive (4) Climbing Rocks Janesville, WI 53545 1-800-888-1232 with Hardware www.swing-n-slide.com (1) Multicolor Tarp (1) Name Plate (4) Swing Hangers (4) Safety Handles (2) Swing Seats weight limit: 115 lbs. Kodiak...
  • Page 174 Project 515 KoDIAK 515 KODIAK 514 OPTIONAL LADDER 8 - 2"X4"X96" 2 - 2"X4"X96" 6 - 2"X4"X120" 2 - 2"X4"X120" 12 - 5/4"X6"X120" 10 - 5/4"X6"X144" OPTIONAL ROCK WALL 9 - 4"X4"X96" 2 - 2"X4"X96" 5 - 4"X4"X120" 1 - 2"X4"X120" 3 - 5/4"X6"X120"...
  • Page 175 Project 515 39 3/4" 39 3/4" 39 3/4" "X6"X120" 54" 54" "X6"X120" 39 1/2" 39 1/2" 39 1/2" "X6"X120" 39 1/2" 36" 36" "X6"X120" 38 1/2" 38 1/2" 38 1/2" "X6"X120" 43-1/4" 43-1/4" 43-1/4" "X6"X144" 72" 36" 36" "X6"X144" 96" 38 1/2"...
  • Page 176 Project 515 How to select the correct fastener Use these 3 pictorial guides to help select the correct fastener(s) for the lumber attachment you are making. Each diagram will highlight the correct number of fasteners to use, and where to attach them. 5/4'' x 6'' to 4'' x 4'' 2-1/2'' screws Apply the 2-1/2"...
  • Page 177 Project 515 Understanding how the Bracket System Works Example of a Shelf-Loc bracket connection. Shelf-Loc Bracket correct! Wrap-Loc WroNG! brackets ''clipped'' brackets Not interlocked! Example of a Shelf-Loc bracket connection. Look for ''TOP'' stamp on bracket for correct orientation. top of bracket Introduction to the Bracket system LW YS Use 2'' lag screws on all brackets.
  • Page 178 Project 515 4'' x 4'' x 96'' Fig.1 Look for ‘’TOP’’ Use a 2’’ lag screw stamp on brackets to hold bracket in while installing. place for later use. 2'' lag screws per bracket 82-1/2'' 55-1/4'' 55-1/4'' 2'' Lag screw .
  • Page 179 Project 515 •WARNING• Avoid splitting your lumber by offsetting your screws at least 3/4’’ from edge. 2-1/2'' screws Fig.1a (1) 2'' lag screw (4) 2-1/2'' screws . Frame 1 Construction cont. 2. ttach upper 2'' x 4'' and lower 5/4'' boards as shown 2'' Lag screw in (Fig.
  • Page 180 Project 515 4'' x 4'' x 120'' Fig.2 Look for ‘’TOP’’ Use a 2’’ lag screw stamp on brackets to hold bracket in while installing. place for later use. 2'' lag screws per bracket 76-3/4'' 82-1/2'' 2'' Lag screw 55-1/4'' B.
  • Page 181 Project 515 Fig.2a B. Frame 2 Construction cont. 2-1/2'' screws 2. ttach upper 2'' x 4'' and lower 5/4'' boards as shown in (Fig. 2a) 69-1/2'' 62'' 2-1/2'' screw...
  • Page 182 Project 515 Fig.3 Look for ‘’TOP’’ Use a 2’’ lag screw stamp on brackets to hold bracket in while installing. place for later use. 4'' x 4'' x 120'' 2'' lag screws per bracket 76-3/4'' 55-1/4'' 2'' Lag screw C. Frame 3 Construction 1.
  • Page 183 Project 515 Fig.3a 2-1/2'' screws C. Frame 3 Construction cont. 2. ttach upper 2'' x 4'' and lower 5/4'' boards as shown in (Fig. 3a) 80-1/2'' (1) 2'' lag screw (4) 2-1/2'' screws 2'' Lag screw 2-1/2'' screw...
  • Page 184 Project 515 2-1/2'' screws Fig.4 (1) 2'' lag screw (4) 2-1/2'' screws D. Frame Construction 1. Install 2’’ x 4’’ and 5/4'' boards as shown above. 2'' Lag screw 2-1/2'' screw...
  • Page 185 Project 515 Fig.4a Double check to make sure structure is square 2-1/2'' screws (1) 2'' lag screw (4) 2-1/2'' screws D. Frame Construction cont. 1. ttach Frame Two as shown above. 2'' Lag screw 2-1/2'' screw...
  • Page 186 Project 515 Tip: Flex brackets to make installation of 4'' x 4'' easier Fig.5 Fig. 5a Approx. 1/4'' F. Install 4x4s 2'' Lag Screws 1. Work (2) 4'' x 4'' into brackets as shown in(Fig. 5), (Fig 5a). 2. Secure brackets (Fig. 5b). 2'' Lag screw Fig.5b...
  • Page 187 Project 515 Fig.6 Double check to make sure structure is square ttach Frame 3. 1. ttach and secure Frame 3 to rest of unit as shown above. (4) 2'' Lag Screws (4) 2-1/2'' screws (1) 2'' lag screw (Per joint) 2'' Lag screw 2-1/2'' screw...
  • Page 188 Project 515 Fig.7 2-1/2'' screws 2-1/2'' screw G. Install Deck Boards 1. Install 5/4'' deck boards to structure as shown (Fig. 7). 2. Use two 2-1/2'' screws at each end of deck boards. Note: On End Boards, avoid screwing into Shelf Brackets by placing screws behind Shelf Bracket location.
  • Page 189 Project 515 Fig.7a 2-1/2'' screws 2-1/2'' screws H. Center & Entrance Support Boards 1. Install 4’’ x 4’’ support boards as shown in (Fig. 7a). 2. Secure bottom of 4’’ x 4’’ as shown in (Fig 7a) 2-1/2'' screw...
  • Page 190 Project 515 Fig.8 b o t t o m V i e w Fig.8a 2-1/2'' screws 2-1/2'' screws (20) 2-1/2'' screws 2-1/2'' screw H. Center & Entrance Support Boards 1. Construct support boards as shown in (Fig. 8). 2. Secure center of floor boards as shown in (Fig. 8b) 3.
  • Page 191 Project 515 Fig.9 2-1/2'' screws per joint 2-1/2'' screws 2-1/2'' screws per joint 2-1/2'' screws I. Install Lower Rail Board 2-1/2'' screw 1. Install lower 2'' x 4'' rail board as shown in (Fig 9). Flush with the sides of 4'' x 4'' deck supports. NOTE: The bottom screw in the 2'' x 4'' board should secure into the side of the 5/4'' x 6'' deck board.
  • Page 192 Project 515 Tip: Flex brackets to make installation of 4'' x 4'' easier Fig.10a Approx. 1/4'' Allow 4'' x 4''s To Overhang 1'' Fig.10b 2'' Lag screw K. Install 4x4s cont. 1. Work (2) 4'' x 4'' into brackets as shown in (Fig. 10a), (Fig 10). 2.
  • Page 193 Project 515 Fig.11 2-1/2'' Deck Screws (2 per joint) FIG. 11a Fig.11a 2'' screws 2-1/2'' screw L. Install Deck Boards 1. Install 5/4'' deck boards to structure as shown (Fig. 11). 2. Use two 2-1/2'' screws at each end of deck boards. Where shelf bracket blocks screw path, center board and place one screw on either side.
  • Page 194 Project 515 Fig.12 2-1/2'' Screws (2 per joint) M. Install Upper Rail Boards 1. Install upper 2’’ x 4’’ rail boards as shown in (Fig 12). Flush with the top of 4’’ x 4’’ deck supports. 2-1/2'' screw...
  • Page 195 Project 515 2-1/2'' Screws (2 per joint) Fig.13 2-1/2'' Screws (2 per joint) From opposite side of Filler Boards. 2-1/2'' screw N. Install supports cont. 1. Install 2'' x 4'' as shown in (Fig 13)
  • Page 196 Project 515 Fig.14 2-1/2'' Screws 2-1/2'' Screws (3 per joint) 2-1/2'' Screws 2-1/2'' screw N. Install supports cont. 1. Install 2'' x 4'' flush with top of Shelf-Loc Bracket as shown in (Fig 14) 2. Install step as shown in (Fig 14).
  • Page 197 Project 515 Fig.15 Tip: Flex brackets to make installation of 4'' x 4'' easier 2-1/2'' Screws Fig. 15a Approx. 1/4'' 2'' Lag Screws Fig.16 O. Install accessory 4x4 1. Work (1) 4'' x 4'' into brackets as shown in (Fig. 15a), (Fig 15). 2.
  • Page 198 Project 515 Optional Laminated Beam Note: Lay the lumber on a flat surface before beginning laminated beam assembly. Fig. 17 24" Note: Attach one end of the beam with three 2-1/2'' screws. Secure boards and attach the other end with three 2-1/2'' screws. This will insure that your boards will stay aligned throughout the remainder of the beam assembly.
  • Page 199 Project 515 Fig. 18 Q. Swing Beam Drill Locations 1. Use a 3/8'' drill bit to drill a 3/8’’ hole through the beam at each location shown in (Fig. 18) 2. Install Swing Hangers onto swing beam at locations shown. Note: Swing Hangers must be installed on same side dimensions were originally marked.
  • Page 200 Project 515 Hammer Fig. 19 3/8'' hole T-nut t-nut Bottom Beam Clamp (4) 1-1/4'' screws Use Screwdriver to aid in tightening Swing Hanger Q. Swing Beam Drill Locations 1. Tap t-nut into 3/8’’ hole as shown in (Fig. 19) 2. Place a bottom beam clamp over the swing hanger as shown in (Fig. 19) 3.
  • Page 201 Project 515 -Frame ssembly (8) 2-1/2’’ Screws Fig. 20 1. layout 4'' x 4’’s as shown in (Fig. 20) lign EZ Frame Bracket with face of 4'' x 4''s. 3. Secure EZ Frame Bracket with (8) 2-1/2'' screws to 4'' x 4''s making sure they are flush with each other.
  • Page 202 Project 515 Fig. 22 T-nut Washer 2-1/2'' screws 5-1/2’’ Hex Bolt 2-1/2'' screw -Frame ssembly cont. 1. 1. Tap T-nut into 3/8’’ hole as shown in (Fig. 22) Note: If using Laminated Swing Beam, make sure T-nut teeth do not fall between seams of 2'' x 6''s. ttach -Frame beam to Swing Beam using (2) 5-1/2’’...
  • Page 203 Project 515 Fig. 23 -Frame ssembly cont. 1. Position Split-Brackets on 4'' x 4'' x 55'' (Fig 23). 2. With the help of others, lift -Frame and Swing Beam ssembly and center on to unit as shown in (Fig. 23) 3.
  • Page 204 Project 515 Fig.25 (1) 2'' x 4'' x 71'' 2-1/2'' Deck Screws Fig.25b (4) 5/4'' x 6 38-1/2'' (6) 5/4'' x 6’’ x 38-1/2'' 2'' Deck Screws (2 per joint) (6) 5/4'' x 6’’ x 36'' Use 2-1/2'' screws to 2'' Deck Screws secure to 5/4'' x 6'' to 4'' x 4'' (2 per joint)
  • Page 205 Project 515 Fig.26 (3) 5/4'' x 6'' x 38-1/2'' 2'' Deck Screws (2 per joint) Fig.26a V. Barrier Boards cont. 1. Install 5/4'' barrier boards evenly spaced in the opening. 2'' Deck Screws (2) 5/4'' x 6'' x 36'' (2 per joint) 2-1/2'' Deck Screws (2 per joint on 2'' x 4''s) 2'' screw...
  • Page 206 Project 515 Fig.27 2-1/2'' Deck Screws W. Support Boards. (3 per joint) 1. Constuct 2'' x 4''s as shown in (Fig 27) 1-1/2'' 2-1/2'' screw...
  • Page 207 Project 515 Fig.28 2-1/2'' Deck Screws (2 per joint) W. Support Boards. 1. Constuct 2'' x 4''s as shown in 2-1/2'' screw (Fig 28)
  • Page 208 Project 515 Fig.29 (4) 5/4'' x 6'' x 39-1/2'' 2'' Deck Screws (2 per joint) Fig.30 (4) 5/4'' x 6'' x 34-3/4'' 2'' Deck Screws (2 per joint) X Barrier Boards. 1. Install 5/4'' x 6'' boards evenly spaced as shown in (Fig 29) and (Fig. 30). 2'' screw...
  • Page 209 Project 515 sIDe oPeNING oPtIoN 1...
  • Page 210 Project 515 sIDe oPeNING oPtIoN 1 EXA MPLE OF LA D D ER R UNG I NS TA LLAT I O N 2-1/2'' 1-1/4'' screws O. Ladder ssembly. • BOTTOM OF LADDER RAIL • 1. On ladder rails, mark all measurement locations for Fig.
  • Page 211 Project 515 2-1/2'' Deck Screws (2 per joint) Fig.34 Y. Install Tarp. 1. Install tarp as shown in (Fig. 34) 2. Secure tarp in six locations (Fig 34a). 2-1/2'' Deck Screws 2-1/2'' screw Fig.34a 1-1/4'' screw...
  • Page 212 Project 515 Fig. 35 2-1/2'' Deck Screws (3 Per joint) 26-1/4'' 2-1/2'' screw Z1. Install Protective Barrier Board 1. Secure protective 5/4'' barrier board as shown in (Fig 35).
  • Page 213 Project 515 Fig. 36 Fig. 37 washer 11" 1 - 3/4 Panhead screw Deck Surface INstAll PlAy HANDles Here 1'' truss screw Use truss head screws to to secure slide to deck. Slide/Safety Handle Installation. 1. Mount safety handles in the ladder THIS PRODUCT IS opening approximately 11'' above the INTENDED FOR USE...
  • Page 214 Project 515 Anchor-It (Sold Seperately) Fig. 38 Flat Washer metal strap 1-1/2" lag bolt Anchor-It stake nchor-It Installation (optional). Instructions for nchoring Swing•N•Slide ctivity Centers 1. Determine the final location of your activity center. 2. Place the Anchor- It stakes adjacent to the base and near the corners of your activity center (at the bottom of the legs on swing sets) and twist the auger- style stakes into the ground until only the loop is exposed.
  • Page 215 Project 515 Fig. 39 2. Unit Modification cont. 2-1/2'' screw (1) Install 2'' x 4'' frame and support as shown in (Fig. 39).
  • Page 216 Project 515 Fig. 40a Fig. 40 2-1/2'' screws (Per joint) 10'' 2-1/2'' Deck Screws (2 Per joint) 4-1/8'' 20-1/8'' 2-1/2'' screw NOTE: 5' Climbing Rock Wall will require Fig. 40b Min. 12 Climbing Rocks (3) Bags of Climbing Rocks. NE 4543S Climbing Wall Lumber Cut List.
  • Page 217 Project 515 bAcK oPeNING oPtIoN 2 Fig. 41a Fig. 41 NOTE: Remove (3) 5/4'' x 6'' Barrier Boards 2-1/2'' Deck Screws 4-1/2'' 21'' 2-1/2'' screw NOTE: 7' Climbing Rock Wall will require Fig. 41b 16 Climbing Rocks (4) Bags of Climbing Rocks.
  • Page 218 Project 515 Climbing Rock Climbing Rock Fig. 42 (2)"T" nuts 3/8" Holes (2) 2'' Hex Head Bolts Hold (rock) (1) Loc Washer per bolt (1) Flat Washer per bolt Climbing Rock Installation 1. Mark locations of Climbing Rocks on the Climbing Wall in a pattern that will easily allow your child to climb to the deck.
  • Page 219 Project 515...
  • Page 220 Questions???... Call our Customer Service Department at 1-800-888-1232 © PlayCore Inc. 2012 Printed In USA LA 6707...
  • Page 221 Swing•N•Slide • 1212 Barberry Drive • Janesville, Wisconsin 53545 Visite nuestro sitio web en www.swing-n-slide.com o llámenos al Visitez notre site Web au www.swing-n-slide.com ou appelez-nous au...
  • Page 222 Cuando el equipo sea retirado de servicio, se debe desarmar y desechar de tal manera que no presente peligros no razonables al momento de desecharlo. ¡Importante! Instrucciones de seguridad adicionales para todos los equipos de juego Swing-N-Slide. Guardar esta hoja de instrucciones en caso de que se requiera contactar al fabricante.
  • Page 223 Swing-N-Slide® DESCONOCE TOD S L S DEMÁS DECL R CIONES Y G R NTÍ S DE CU LQUIER TIPO, EXPRES S, IMPLÍCIT S, EST TUT RI S U OTR S, INCLUID S L S G R NTÍ...

  • Page 224: Iinstallation Sécuritaire - Vez-Vous

    Lorsque l’équipement est mis hors service, il doit être démonté et conditionné de sorte qu’aucun danger justifié ne sera présent lors de la mise au rebut de l’ensemble. Important! Instructions supplémentaires de sécurité pour tous les centres de jeu Swing-N-Slide. Conserver ce feuillet d’instruction au cas où vous devriez prendre contact avec le fabricant.
  • Page 225 Swing-N-Slide® RENONCE À TOUTES UTRES REPRÉSENT TIONS ET G R NTIES DE TOUTES SORTES, EXPLICITES, IMPLICITES, RÉGLEMENT IRES OU UTRES, Y COMPRIS LES G R NTIES IMPLICITES DE QU LITÉ M RCH NDE ET D' DÉQU TION À UN US GE P RTICULIER. Swing-N-Slide® N’EST P S RESPONS BLE DES DOMM GES CCESSOIRES OU INDIRECTS.
  • Page 226 PROYECTO 515/PROJET 515 HERRAMIENTAS NECESARIAS/OUTILS REQUIS sIERRa CIRCulaR maRTIllO TaladRO ElÉCTRICO dadO Y llaVE dE 1/2" (1.2 cm) sCIE CIRCulaIRE maRTEau PERCEusE ÉlECTRIQuE ClÉ ET dOuIllE dE 1/2 po (12 mm) GaFas dE sEGuRIdad bROCa dE TaladRO dE 3/8" (0.95 cm) bROCa dE EsTRElla EsCuadRa dE CaRPInTERO CInTa mÉTRICa...
  • Page 227 Use ONLY 1212 Barberry Drive (4) piedras para escalar con piezas Janesville, WI 53545 1-800-888-1232 (4) Prises d’escalade avec quincaillerie www.swing-n-slide.com (1) Cubierta (1) Toit (1) placa del nombre (1) Plaque d’identification (4) Colgaderos de columpio (4) Supports de balançoire...
  • Page 228 PROYECTO 515/PROJET 515 KOdIaK 515 KODIAK 514 OPTIONAL LADDER 8 - 2"X4"X96" 2 - 2"X4"X96" 6 - 2"X4"X120" 2 - 2"X4"X120" 12 - 5/4"X6"X120" 10 - 5/4"X6"X144" OPTIONAL ROCK WALL 9 - 4"X4"X96" 2 - 2"X4"X96" 5 - 4"X4"X120" 1 - 2"X4"X120" 3 - 5/4"X6"X120"...
  • Page 229 1 - 2"X4"X120" 54" 54" PROYECTO 515/PROJET 515 1 - 2"X4"X120" 54" 39 1/2" 20" 1 - 2"X4"X120" 39 3/4" 39 3/4" 39 3/4" "X6"X120" 54" 54" "X6"X120" 39 1/2" 39 1/2" 39 1/2" "X6"X120" 39 1/2" 36" 36" "X6"X120" 38 1/2"...
  • Page 230 PROYECTO 515/PROJET 515 Cómo seleccionar el sujetador apropiado Comment choisir le bon système d'attache Utilice estas tres guías ilustradas para seleccionar el (los) sujetador(es) apropiado(s) para el ajuste de maderas que usted está haciendo. Cada diagrama resaltará el número correcto de sujetadores que debe usarse, y dónde fijarlos. Utilisez ces 3 guides illustrés pour faciliter le choix du ou des système(s) d'attache(s) pour l'assemblage de pièces de bois concernées.
  • Page 231 PROYECTO 515/PROJET 515 Cómo funciona el sistema de abrazaderas Comprendre le fonctionnement du système de fixation Ejemplo de una conexión con abrazadera de estante. abrazadera de estante Connecteur « Shelf-Loc » Exemple de connecteur «  Shelf-Loc  ». ¡CORRECTO!/bOnnE mÉTHOdE! abrazadera de envoltura Connecteur Wrap-Loc ¡InCORRECTO!/mauVaIsE mÉTHOdE! abrazaderas entrelazadas...
  • Page 232 PROYECTO 515/PROJET 515 4" x 4" x 96" Fig. 1 Busque la marca ‘’TOP’’ Use a 2’’ lag screw sobre las abrazaderas to hold bracket in cuando esté realizando place for later use. la instalación. Recherchez l'estampille « TOP » (dessus) sur les fixations pendant l'installation.
  • Page 233 PROYECTO 515/PROJET 515 •ADVERTENCIA• Evite rajar la madera colocando los tornillos a una distancia de al menos 3/4" desde el borde. •AVERTISSEMENT!• Évitez de fendre votre pièce de bois en décalant vos vis à au moins 3/4" du rebord. tornillos de 2 1/2" Trois (3) Fig.
  • Page 234 PROYECTO 515/PROJET 515 4" x 4" x 120" Fig. 2 Busque la marca ‘’TOP’’ Use a 2’’ lag screw sobre las abrazaderas to hold bracket in cuando esté realizando place for later use. la instalación. Recherchez l'estampille « TOP » (dessus) sur les fixations pendant l'installation.
  • Page 235 PROYECTO 515/PROJET 515 Fig. 2a tornillos de 2-1/2" (6.4 cm) Vis 2-1/2 po (63,5 mm) B. Construcción del marco 2 (cont.) 2. Fije las tablas superiores de 2'' x 4'' (5.1 x 10.2 cm) e inferiores de 5/4'' (3.2 cm) como se muestra en la (Fig.
  • Page 236 PROYECTO 515/PROJET 515 Fig. 3 Busque la marca ‘’TOP’’ Use a 2’’ lag screw sobre las abrazaderas to hold bracket in cuando esté realizando place for later use. la instalación. Recherchez l'estampille « TOP » (dessus) sur les fixations pendant l'installation.
  • Page 237 PROYECTO 515/PROJET 515 Fig. 3a tornillos de 2 1/2" Trois (3) vis de 2 1/2" C. Construcción del marco 3 cont. 2. Fije las tablas superiores de 2" x 4" e inferiores de 5/4" como se muestra en la (Fig. 3a). C.
  • Page 238 PROYECTO 515/PROJET 515 tornillos de 2 1/2" Fig. 4 Trois (3) vis de 2 1/2" (1) tornillo de compresión de 2" (4) tornillos de 2 1/2" Un (1) vis tire-fond de 2" Quatre (4) vis de 2 1/2" D. Construcción del marco 1.
  • Page 239 PROYECTO 515/PROJET 515 Fig.4a Verifique dos veces que la estructura tornillos de 2-1/2" (6.4 cm) esté en escuadra Effectuez une double Vis 2-1/2 po (63,5 mm) vérification pour vous assurer que la charpente est à l'équerre (1) tornillo de compresión de 2'' (5.1 cm) (4) tornillos de 2-1/2"...
  • Page 240 PROYECTO 515/PROJET 515 Consejo: Doble las abrazaderas para facilitar la instalación de la pieza de 4" x 4" Conseil : utilisez les fixations flexibles pour faciliter l'installation des poutres de 4" x 4" Fig. 5 Fig. 5a Aprox. 1/4" Approx. 1/4" F.
  • Page 241 PROYECTO 515/PROJET 515 Fig. 6 Verifique dos veces que la estructura esté en escuadra Effectuez une double vérification pour vous tornillos de compresión assurer que la charpente de 2" por abrazadera est à l'équerre deux (4) vis tire-fond de 2" par fixation (1) tornillo de compresión de 2"...
  • Page 242 PROYECTO 515/PROJET 515 Fig. 7 tornillos de 2-1/2" (6.4 cm) Vis 2-1/2 po (63,5 mm) Tornillo de 2 1/2" Vis de 2 1/2" G. Instale las tablas de la plataforma 1. Instale las tablas de 5/4'' (3.2 cm) de la plataforma a la estructura como se muestra en la (Fig. 7). 2.
  • Page 243 PROYECTO 515/PROJET 515 Fig. 7a tornillos de 2 1/2" Trois (3) vis de 2 1/2" tornillos de 2 1/2" Trois (3) vis de 2 1/2" H. Tablas de soporte del centro y de la entrada 1. Instale las tablas de soporte de 4" x 4" como se indica en la (Fig.
  • Page 244 PROYECTO 515/PROJET 515 V i s t a i n f e r i o r / V u e d e s s o u s Fig. 8 Fig. 8a tornillos de 2 1/2" Quatre (4) vis de 2 1/2" tornillos de 2 1/2"...
  • Page 245 PROYECTO 515/PROJET 515 Fig. 9 tornillos de 2 1/2" por junta Trois (3) vis de 2 1/2" par joint tornillos de 2 1/2" Cinq (5) vis de 2 1/2" tornillos de 2 1/2" por junta tornillos de 2 1/2" Trois (3) Cinq (5) vis de 2 1/2"...
  • Page 246 PROYECTO 515/PROJET 515 Consejo: Doble las abrazaderas para facilitar la instalación de los 4'' x 4'' (10.2 x 10.2 cm) Conseil : pliez le connecteur pour faciliter l'installation du 4 po x 4 po (100 mm x 100 mm) Fig. 10a Aprox.
  • Page 247 PROYECTO 515/PROJET 515 Fig. 11 tornillos de plataforma de 2-1/2'' (6.4 cm) (2 por junta) Vis de plateforme 2-1/2 po (63 mm) (2 par joint) FIG. 11a Fig. 11a tornillos de 2'' (5.1 cm) Vis 2 po (50 mm) Tornillo de 2 1/2"...
  • Page 248 PROYECTO 515/PROJET 515 Fig. 12 tornillos de 2-1/2" (6.4 cm) por junta Vis 2-1/2 po (64 mm) par joint I. Instale la tabla del riel superior 1. Instale la tabla de 2'' x 4'' (5.1 x 10.2 cm) del riel superior como se muestra en la (Fig.

  • Page 249: Installez Les Supports (Suite)

    PROYECTO 515/PROJET 515 tornillos de 2-1/2" (6.4 cm) (2 por junta) Vis 2-1/2 po (64 mm) (2 par joint) Fig. 13 tornillos de 2 1/2" (2 por junta) del lado opuesto de las tablas de relleno. Quatre (4) vis de 2-1/2 po (2 par joint) du côté...
  • Page 250 PROYECTO 515/PROJET 515 Fig. 14 tornillos de 2-1/2" (6.4 cm) Vis 2-1/2 po (64 mm) tornillos de 2-1/2" (6.4 cm) tornillos de 2-1/2" (3 por junta) (6.4 cm) Vis 2-1/2 po (64 Vis 2-1/2 po (64 mm) (3 par joint) Tornillo de 2 1/2"...
  • Page 251 PROYECTO 515/PROJET 515 Fig. 15 Consejo: Doble las abrazaderas para facilitar la instalación de la pieza de 4" x 4" Conseil : Ployez les fixations pour faciliter l'installation des 4" x 4" Tornillos de 2 1/2" Trois (3) vis de 2 1/2 Fig.
  • Page 252 PROYECTO 515/PROJET 515 Viga laminada opcional/Poutre laminée en option nOTa: Disponga la madera sobre una superficie plana antes de iniciar el ensamblaje de la viga laminada. REmaRQuE : déposez les pièces de bois d'ceuvre sur une surface horizontale avant de commencer l'assemblage de la poutre laminée. Fig.
  • Page 253 PROYECTO 515/PROJET 515 Ubicación de perforación de 3/8" Emplacement des trous de 3/8" fait avec une perceuse Fig. 18 Q. Ubicación de las perforaciones de la viga del columpio 1. Utilice una broca de 3/8" para hacer una perforación de 3/8" a través de la viga en cada lugar que se muestra en la (Fig.
  • Page 254 PROYECTO 515/PROJET 515 Martillo Marteau Fig. 19 Orificio de 3/8'' Trou de 3/8'' Tuerca en T Écrou en T encastré Abrazadera de la viga inferior Attache de base de poutre Use el destornillador para ajustar Utilisez un tournevis pour mieux serrer (4) tornillos de 1 1/4"...
  • Page 255 PROYECTO 515/PROJET 515 R. Disposición del montaje de la (8) tornillos de 2 1/2" estructura en Huit (8) vis 2 1/2" Fig. 20 1. 4" x 4"s como se muestra en la (Fig. 20). 2. linee la abrazadera del marco EZ con la cara de las piezas de 4"...
  • Page 256 PROYECTO 515/PROJET 515 Tuerca en T Écrou en T encastré Fig. 22 Arandela Rondelle Tornillos de 2 1/2" vis de 2 1/2" Perno de cabeza hexagonal de 5 1/2" Boulon à tête hexagonale de 5 1/2" Tornillo de 2 1/2" Vis de 2 1/2"...
  • Page 257 PROYECTO 515/PROJET 515 Fig. 23 T. Montaje del marco en (cont.) 1. Ubique los soportes divisores en la pieza de 4" x 4" x 55" (Fig. 23) 2. Con ayuda de otras personas, levante el marco en y el conjunto de la viga del columpio y céntrelos en la unidad como se muestra en la (Fig.
  • Page 258 PROYECTO 515/PROJET 515 Tornillos de Fig. 25 (1) 2" x 4" x 71" plataforma de 2 1/2" Trois (3) vis à terrasse de 2 1/2" Fig. 25b (4) 5/4" x 6 38-1/2" (6) 5/4" x 6" x 38-1/2" Tornillos de plataforma de 2"...

  • Page 259: Planches De Barrière (Suite)

    PROYECTO 515/PROJET 515 Fig. 26 (3) 5/4" x 6" x 38-1/2" Tornillos de plataforma de 2" (2 por junta) Deux (2) vis à terrasse de 2" (2 par joint) Fig. 26a V. Tablas de la barrera (cont.) 1. Instale las tablas de 5/4'' (3.2 cm) de la barrera uniformemente espaciadas en la abertura.
  • Page 260 PROYECTO 515/PROJET 515 Fig. 27 2-1/2" Deck Screws V. Tablas de la barrera (cont.) (3 per joint) 1. Construya las tablas de 2" x 4" como se muestra en la (Fig. 27). Tornillos de plataforma de 2-1/2" (2 por junta) 1-1/2"...
  • Page 261 PROYECTO 515/PROJET 515 Fig. 28 tornillos de 2-1/2" (6.4 cm) por junta Vis 2-1/2 po (64 mm) par joint W. Tablas de la barrera (cont.) 1. Construya las tablas de 2" x 4" como se muestra en la (Fig. 28). W.
  • Page 262 PROYECTO 515/PROJET 515 Fig. 29 (4) 5/4" x 6" x 39-1/2" Tornillos de plataforma de 2" (2 por junta) Deux (2) vis à terrasse de 2" (2 par joint) Fig. 30 (4) 5/4" x 6" x 34-3/4" Tornillos de plataforma de 2"...
  • Page 263 PROYECTO 515/PROJET 515 OPCIÓn dE aPERTuRa laTERal 1 OuVERTuRE laTÉRalE OPTIOn 1...
  • Page 264 PROYECTO 515/PROJET 515 OPCIÓn dE aPERTuRa laTERal 1 OuVERTuRE laTÉRalE OPTIOn 1 EJEMPLO DE INSTALACIÓN DE PELDAÑOS DE LA ESCALERA EXEMPLE D'INSTALLATION DES BARREAUX D'ÉCHELLE 2-1/2" tornillos de 1-1/4" Six (6) Vis de 1-1/4" O. Ensamblaje de la escalera. 1. Sobre los rieles de la escalera, marque en cada lado con un lápiz la ubicación de todas las medidas.
  • Page 265 PROYECTO 515/PROJET 515 tornillos de 2-1/2" (6.4 cm) vis de 2-1/2 po (65 mm) Fig. 34 V. Tablas de la barrera 1. Instale dos soportes de techo de 2'' x 4'' (5.1 x tornillos de 2-1/2" (6.4 cm) 10.2 cm) como se muestra en la (Fig. 34) vis de 2-1/2po (65 mm) V.

  • Page 266: Fig. 35

    PROYECTO 515/PROJET 515 Fig. 35 tornillos de plataforma de 2 1/2’’ (3 por junta) 26-1/4" Vis de plateforme de 2-1/2’’ (3 par joint) Tornillo de 2-1/2" (6.4 cm) vis de 2-1/2po (65 mm) Protector del columpio 1. Instale el protector del columpio de 5/4" x 6" como se muestra en la (Fig. 35). Dispositif de sécurité...

  • Page 267: Fig. 37

    2. Installez la glissoire, comme illustré (Fig. 37). de 4" x 4" donde pueda leerse fácilmente Important : .swing-n-slide.com Fixez votre étiquette d'identification du produit à un endroit Veillez à ne pas utiliser les fixations fournies avec la glissoire Utilisez les vis à tête bombée comprises dans la trousse.
  • Page 268 PROYECTO 515/PROJET 515 Anchor-It Anclaje/« Anchor-It » (Sold Seperately) Fig. 38 arandela plana Rondelle plate correa metálica Courroie de métal pernos de de 1 1/2" 1 1/2" Tire-fond Anclaje « Anchor-It » Y. Instalación del anclaje. Instrucciones para anclar los centros de actividades Swing•N•Slide 1.
  • Page 269 PROYECTO 515/PROJET 515 Fig. 39 2. Modificación de la unidad cont. (1) Instale el marco de 2" x 4" y el soporte como se muestra en (Fig. 39). Tornillo de 2 1/2" 2. Modification de l'unité (suite) Vis de 2 1/2" (1) Installez le cadre en 2"...

  • Page 270: Trois

    PROYECTO 515/PROJET 515 Fig. 40a Fig. 40 tornillos de 2 1/2" (Por junta) Deux (2) Vis de 2 1/2" (par joint) 10" Tornillos de plataforma de 2 1/2" (2 por junta) Vis à terrasse de 2 1/2" (2 par joint) 4-1/8"...
  • Page 271 PROYECTO 515/PROJET 515 Fig. 41a Fig. 41 NOTA: Retire las (3) tablas de 5/4'' x 6" (3.2 x 15.2 cm) de la barrera de protección. REMARQUE : Retirez (2) planches de barrière de de Tornillos de plataforma de 2-1/2'' (6.4 cm) 5/4 po x 6 po (32 x 152 mm) Vis de plateforme de...
  • Page 272 PROYECTO 515/PROJET 515 Climbing Rock Climbing Rock Fig. 42 (2) tuercas en “T” (2) Écrous en « T » (2) pernos con cabeza hexagonal de 2" agujeros de 3/8" (2) Boulons à tête hexagonale de 2" Trous de 3/8" sostén (piedra) Prise (rocher) (1) arandela de bloqueo por perno (1) arandela plana por perno...

Table des Matières