1. Manuels
  2. Marques
  3. Swing-N-Slide Manuels
  4. Ensembles de jeux et équipements de terrains de jeux
  5. pb 9241
  6. Instructions d'assemblage

Swing-N-Slide pb 9241 Instructions D'assemblage

Masquer les pouces
Table des Matières

Publicité

Liens rapides

Télécharger ce manuel
Pb 9241
AssEMbly INsTRUcTIONs
No. of children: Up to 10
Min. Use Zone: 30 ' x 29 '
set Dim. 18 'L x 13 'W x 11'H
Est. building Time: 9-12 hrs.
IMPORTANT!!
PLEASE READ BEFORE BEGINNING ASSEMBLY!!
Please make sure all lumber, hardware and accessory parts are accounted for. If you are missing
anything, please
DO NOT RETURN
to the store where purchased. Please call our Customer
Service Department at the number below.
To register your product visit:
http://www.swing-n-slide.com
Other benefits include information on product warranties, assembly plan updates, joining our mailing
list for new products and promotions, receiving our newsletter, and providing feedback on products.
Swing•N•Slide • 1212 Barberry Drive • Janesville, Wisconsin 53545
Visit our web site at: www.swing-n-slide.com or call us at
1-800-888-1232

Publicité

Table des Matières
loading

Manuels Connexes pour Swing-N-Slide pb 9241

Sommaire des Matières pour Swing-N-Slide pb 9241

  • Page 1 Other benefits include information on product warranties, assembly plan updates, joining our mailing list for new products and promotions, receiving our newsletter, and providing feedback on products. Swing•N•Slide • 1212 Barberry Drive • Janesville, Wisconsin 53545 Visit our web site at: www.swing-n-slide.com or call us at 1-800-888-1232...

  • Page 2: Disposal Instructions

    When the equipment is taken out of service, it must be disassembled and disposed of in such a way that no unreasonable hazards will exist at the time the set is discarded. Important! Additional Safety Instructions for all Swing-N-Slide Playground Equipment. Save this instruction sheet in the event the manufacturer needs to be contacted.
  • Page 3 Swing-N-Slide® will repair, or at its discretion, replace any part within the stated warranty period which is defective in workmanship or materials. This decision is subject to verification of the defect upon delivery of the defective part to Swing-N-Slide® at 1212 Barberry Drive, Janesville, Wisconsin, 53545. Any part(s) returned to Swing-N- Slide®...

  • Page 4: Tools Required

    TOOLS REQUIRED TOOLS REQUIRED HAMMER 1/2" & 7/16'' sOcKET & WRENcH ElEcTRIc DRIll sAFETy GlAssEs cARPENTER's sQUARE PHIllIPs bIT TAPE MEAsURE & DUsT MAsK (44) 2'' Lag Screw (4) 1-1/2'' Lag Bolt (4) 5/16 Loc nut (32) 1-1/4'' Lag Screw (4) 1'' Truss Screw (304) 3'' Wood Screw (2) 1/4-20...
  • Page 5 Assembly Instructions Crimp Location (4) 2-1/2'' Carriage Bolt (22) 1/4-20 Locking T-Nut (6) 3/4'' Hex Head Bolt (4) 1-1/2'' Hex Head Bolt (4) 5/16'' T-Nut (2) 2'' Hex Head Bolt (2) 3-1/2'' Hex Head Bolt (4) Wood Loc Washers (4) 4'' Hex Head Bolt (8) 4-1/2'' Hex Head Bolt (4) 5-1/2'' Hex Head Bolt (8) Shelf-Loc...
  • Page 6 RÉSERVÉ À L_UTILISATION PAR DES ENFANTS DE 2 À 10 ANS USAGE RÉSIDENTIEL/FAMILIAL SEULEMENT 1212 Barberry Drive Janesville, WI 53545 1-800-888-1232 www.swing-n-slide.com (1) Name Plate (2) Table Supports (4) 5-1/4'' Swing Hangers (1) Tarp (1) T20 Torx® Bit (4) Anchor-It Straps...
  • Page 7 Assembly Instructions (1) Table Support (1) Discovery Table (1) Window Pane-SQ (2) Swing Seat weight limit: 115 lbs. (1) Alpine Slide Weight Limit: 250 lbs. (8) Climbing Rocks with Hardware (2) Play Handle (1) 2 For Fun with Hardware 150 lb Weight Limit...
  • Page 8 Assembly Instructions Pb 9241 board list (2) [PF 3980] 3’’ x 3’’ x 94’’ (1) [PF 3954] 1’’ x 4’’ x 41’’ (1) [PF 3702] 2’’ x 4’’ x 51-1/2’’ SB Support (2) [PF 3979] 3’’ x 3’’ x 94’’...
  • Page 9 Assembly Instructions How to select the correct fastener Use these 2 pictorial guides to help select the correct fastener(s) for the lumber attachment you are making. Each diagram will highlight the correct number of fasteners to use, and where to attach them. 1'' x 4'' to 3'' x 3'' or 2'' x 4'' 2-1/2'' screws Apply 2-1/2'' screws to the 1'' x 4'' boards...
  • Page 10 Assembly Instructions Assembly Instructions Understanding how the Bracket System Works Example of a Shelf-Loc bracket connection. Shelf-Loc Bracket cORREcT! Wrap-Loc WRONG! brackets ''clipped'' brackets NOT interlocked! Example of a Shelf-Loc bracket connection. Look for ''TOP'' stamp on bracket for correct orientation. Top of bracket Introduction to the Bracket system Wrap-Loc...
  • Page 11 Assembly Instructions Look for ‘’TOP’’ stamp on brackets while installing. DO NOT UsE lAG scREWs HERE Use Lag Screws Only Where Fig. 1 Brackets Attach NOTE HOlE lOcATIONs 1-1/4'' Lag Screws per joint 1-1/4'' Lag screws per bracket 59-1/4'' Frame 1 Frame 1 Assembly 1.
  • Page 12 Assembly Instructions Fig. 2 1/4-20 Locking T-nut Flat Washer screws per joint 4'' Hex Head Bolt Tip: Flex brackets to make installation of 90-1/2'' 2'' x 4'' easier 1-1/4'' Lag Screws 2'' Lag Screws Approx. 1/4'' 1-1/4'' Lag 3'' screws per joint 27'' 2'' Lag...
  • Page 13 Assembly Instructions Fig. 3a FlUsH Fig. 3 3'' screws per joint FlUsH 2-1/2'' screws per 1-3/4'' joint 2'' Lag screw per board 1/4-20 Locking T-nut Flat Washer screws per joint 4'' Hex Head Bolt Frame 1 2''Lag Screw Frames 1 Assembly Cont. 1.
  • Page 14 Assembly Instructions Fig. 4 DO NOT UsE lAG scREWs HERE Use Lag Screws Only Where Brackets Attach 1-1/4'' Lag screws per bracket 1-1/4'' Lag Screws per joint 47-1/4'' 59-1/4'' 47-1/4'' Frame 2 Frame 2 Assembly 1. Attach brackets to the uprights shown in (Fig. 4). Note: There will be no pre-drilled holes in these uprights.
  • Page 15 Assembly Instructions Fig. 5 FlUsH 3'' screws per joint 1-3/4'' (2) 1-1/4'' lag screws (3) 2'' lag screws per bracket Tip: Flex brackets to make installation of 2'' x 4'' easier 53-5/8'' 3'' screws per joint Approx. 1/4'' 1-1/4'' Lag Frame 2 2'' Lag NOTE: Upper screws are (2) 1-1/4''...
  • Page 16 Assembly Instructions Fig. 6 3'' screws per joint Frame 1 3'' screws per joint Support Boards: 1. Attach support boards to Frame 1 as shown in (Fig. 6). 3'' Wood Screw...
  • Page 17 Assembly Instructions Fig. 7 3'' screws per joint Frame 1 47-1/2'' Frame 2 Frame 1 and frame 2 Assembly 1. Attach Frame 2 to Frame 1 as shown in (Fig. 7). 3'' Wood Screw...
  • Page 18 Assembly Instructions Fig. 8 3'' screws per joint Deck Support and Deck Boards 1. Attach (2) Deck Boards and (1) Deck Support Board as shown 3'' Wood Screw in (Fig. 8). Note: The holes at the ends of the Deck Boards should line up with the holes in the tops of the 2'' x 4'' Shelf Brackets.
  • Page 19 Assembly Instructions NOTE: There must be a 1/2'' Fig. 9 Nominal Gap between deck boards. 3'' screws per joint Deck Boards 3'' Wood Screw 1. Attach Deck Boards as shown in (Fig. 9). Note: Center Screws will secure into center Deck Support Board.
  • Page 20 Assembly Instructions Fig. 10 Fig. 10a FlUsH 2'' screws 3'' screws per joint back FlUsH Front 2'' screws 3'' screws per joint Front back bAcK VIEW OF UNIT Deck and Barrier Support Boards 1. Attach Support Boards to tower as shown in (Fig. 10) and 2'' Wood Screw (Fig.
  • Page 21 Assembly Instructions Fig. 11 [PF 3976] 2'' x 4'' x 34'' (4) [PF 3950] 1'' x 4'' x 34'' 2'' screws 1-1/4'' screws per per joint joint Fig. 11a (6) [PF 3950] 1'' x 4'' x 34'' 1-1/4'' screws per joint NOTE: There must be a 1'' Nominal Gap between...
  • Page 22 Assembly Instructions Fig. 12 1-1/4'' screws per joint [PF 3935] 1'' x 4'' x 9-3/8'' [PF 3950] 1'' x 4'' x 34'' [PF 3950] 1'' x 4'' x 34'' FLUSH [PF 3949] 1'' x 4'' x 34'' Window Side Fig. 12a [PF 3949] 1'' x 4'' x 34'' Window Side [PF 3935] 1'' x 4'' x 9-3/8''...
  • Page 23 Assembly Instructions Fig. 13 [PF 3971] 2'' x 4'' x 31-1/4'' Fig. 13a 1/4-20 Locking T-nut Loc Washer Flat Washer 4-1/2'' Bolt Swing Beam Support Board 1. Attach Swing Beam Support Board as shown in (Fig. 13) and (Fig. 13a).
  • Page 24 Assembly Instructions 1-1/2'' Bolt Fig. 14 Fig. 14a Washer 5-1/2'' Bolt Washer 1/4-20 Locking T-nut Washer 1/4-20 Washer Locking 5-1/2'' Bolt T-nut 1/4-20 Locking 1-1/2'' Bolt T-nut Washer 1-1/2'' Bolt T-nuts must be on Top Bolt Heads on Bottom 5-1/2'' Bolt Washer BOTTOM 1/4-20...
  • Page 25 Assembly Instructions Assembly Instructions Fig. 15 Fig. 15a Loc Washer Washer 4-1/2'' Bolt 1/4-20 2'' Bolt Locking Washer T-nut Washer Loc Nut Fig. 15b [PF 3646] 2'' x 4'' x 5-3/8'' Spacer 4-1/2'' Bolt Loc Washer Washer 1/4-20 Locking T-nut 4-1/2'' Hex Head Bolt Swing Beam Support Boards: Loc Washer...
  • Page 26 Assembly Instructions Hammer Bottom Beam Clamp 5/16'' T-Nut Swing Hanger 3/8'' hole 5/16'' T-Nut T-nut Swing Beam (2) 1-1/4'' screws Bottom Beam Clamp Use Screwdriver to aid in tightening 1-1/4'' Wood Screw 5-1/4'' Swing Hanger Swing Hanger Swing Hanger Assembly 1.
  • Page 27 Assembly Instructions Fig. 16 12" 18" Fig. 16a Loc Nut Washer 1-1/4'' screws Carriage Bolt per bracket 18" Fig. 16c Fig. 16b Loc Nut (2) 2-1/2'' screws Washer Bolt Cover 4-1/4'' Swing Hanger Two Child Swing Supports: 1. Along top of Swing Beam mark placement for Two Child Swing 2'' x 4'' Supports as shown in (Fig. 16). 2.
  • Page 28 Assembly Instructions Fig. 17 Fig. 17a 1/4-20 Locking T-nut Loc Nut Washer Washer Loc Washer 4-1/2'' Bolt 2'' Bolt Washer Note: Two Child Swing Supports removed for clarity Swing Beam Attach: 1. Using the assistance of at least one other person, attach Swing Beam Assembly as shown in (Fig. 17) and (Fig.
  • Page 29 Assembly Instructions Fig. 18 Fig. 18a Fig. 18b 3'' screws per joint FLUSH 1-1/4'' Lag screws per joint 2-1/2'' screws per board 50-7/8'' DO NOT UsE lAG scREWs HERE 3'' screws Use Lag Screws Only Where per joint Brackets Attach Frame 3 1-1/4'' Lag Screws...
  • Page 30 Assembly Instructions Fig. 19 Tip: Flex brackets to make installation of 2'' x 4'' easier 2'' screws per joint Fig. 19a 2'' screws Approx. 1/4'' per joint 3'' screws per joint 50-7/8'' 1-1/4'' Screws 2'' Lag Screws 1-1/4'' Screws 2'' Lag 1-1/4'' Lag Screws 3'' screws...
  • Page 31 Assembly Instructions Fig. 20 3'' screws per joint Fig. 20a [PF 3951] 1'' x 4'' x 36'' 3'' screws per joint [PF 3948] 1'' x 4'' x 33'' 14-1/8'' 3'' Wood Screw [PF 3975] 2'' x 4'' x 30'' Lower Deck Supports and Floor Boards 1.
  • Page 32 Assembly Instructions Fig. 21 3'' screws per joint Fig. 21a 1-1/4'' screws per joint (6) [PF 3953] 1'' x 4'' x 39-1/4'' NOTE: There must be a 1/4'' Nominal Gap between Lower Deck boards. (4) [PF 3946] 1'' x 4'' x 30'' NOTE: There must be a 2'' Nominal Gap between back barrier boards.
  • Page 33 Assembly Instructions Fig. 22 NOTE: There must be a 2-1/8'' Nominal Gap between side barrier boards. 1-1/4'' screws per joint Fig. 22a 3'' screws (6) [PF 3946] 1'' x 4'' x 30'' per joint Fig. 22b 16-1/2'' 1-3/4'' [PF 3940] 1'' x 4'' x 20-1/2'' 3'' screws per joint UNDER DEcK VIEW...
  • Page 34 Assembly Instructions Fig. 23 (4) 19'' Ladder Rungs 11-1/4'' 11-1/4'' Fig. 23a Pre-Drill 11-1/4'' 2'' lag screws per rung 14-1/2'' 19'' Ladder Rungs 3/4'' 2'' lag screws UNDER DEcK VIEW Ladder Rungs 1. Install Ladder Rungs as shown in (Fig. 23). 2.
  • Page 35 Assembly Instructions Fig. 24 Fig. 24a 3/8" Holes Rock (2) 1-1/4'' Hex Head Bolts (1) Loc Washer per bolt (1) Flat Washer per bolt 3'' screws per board Fig. 24b (8) [PF 3942] 1'' x 4'' x 24'' 3'' screws 3/4'' per joint (8) [PF 3943] 1'' x 4'' x 24''...

  • Page 36: Roof Assembly

    Assembly Instructions Fig. 25 Fig. 25a [PF 3936] 1'' x 4'' x 12'' Angle 19'' 1-1/2'' screws [PF 3937] 1'' x 4'' x 16-7/8'' Angle [PF 3941] 1'' x 4'' x 21-3/4'' Angle [PF 3945] 1'' x 4'' x 26-5/8'' Arch-C 1-1/2'' screws 1-1/2'' screws per joint...
  • Page 37 Assembly Instructions Fig. 26 Fig. 26a Washer 3 Per Side 3/4'' Screw Fig. 26b 1-1/4'' Wood Screw 1-1/4'' Tarp and Slide Support Installation: screws per board 1. Install Tarp as shown in (Fig. 26) and (Fig. 26a). 2. Install Slide Support Boards as shown in (Fig.
  • Page 38 Assembly Instructions Fig. 27 1'' Truss screws Fig. 27a 1-1/4'' screws per joint Surfacing Material 2'' Above Grade 2'' Below SLIDE Grade STAKE 2'' x 4'' x 17-1/4'' PF 3771 Slide Installation. 1-1/4'' Wood Screw 1. Install Slide centered in the provided opening as shown in (Fig. 27). 2.
  • Page 39 Assembly Instructions Fig. 28 Mount Brackets in the Center of the outer board 36-3/4'' 22-3/4'' 2'' Lag Screws per joint Fig. 28a Fig. 28b (2) 3/4'' Hex Head Bolts 1/4'' Flat Washer Per Side 3/4'' Hex Head Bolts 1/4'' Flat Washer Per Side 2'' Lag screw Discovery Table...
  • Page 40 Assembly Instructions Fig. 28c Fig. 28d 2'' Lag Screws per joint 3/4'' Both Sides Fig. 28e 2-1/2'' Carriage Bolt Wood Loc Washer 5/16'' Washer 5/16'' Loc Nut 2'' Lag screw Discovery Table 1. Install (2) Bench Supports as shown in (Fig. 28c). 2.

  • Page 41: Inside View

    USAGE RÉSIDENTIEL/FAMILIAL SEULEMENT 1212 Barberry Drive Janesville, WI 53545 1-800-888-1232 www.swing-n-slide.com INsIDE VIEW Window Decoration and Name Plate 1. Install Window Decoration Boards as shown in (Fig. 29). 1/2'' Pan Head screw NOTE: Hardware for [PF 3970] will need to be applied from the inside out as shown in (Fig.
  • Page 42 Assembly Instructions Safety Handle Safety Handle: Fig. 30 1/4'' washer 1. Mount safety handle on the posts approximately 11'' 1 - 3/4'' Panhead screw above the deck surface in both the rock wall and ladder openings. (Fig. 30). 2. Reference (Fig. 30a) and (Fig. 30b) for proper location.
  • Page 43 Assembly Instructions Fig. 31 Fig. 31a 2 FOR FUN SWING. 1. Thread chains through 2 for Fun handles as shown in (Fig. 31). 2. Attach handle assembly to seat using (1) 6 1/4" hex head bolts, (1) 5/16" loc washer, (2) 5/16" washers, and (1) 5/16"...
  • Page 44 Assembly Instructions Swing Seats Fig. 32a Fig. 32 Fig. 32b Swing Seat Assembly. 1. Hold the swing seat vertically and insert uncoated chains through the channels on the bottom of the swing seat. Note: A coat hanger may be used to help pull chain through the swing seat. One full link should show at each end of the seat (Fig. 32). 2.
  • Page 45 Assembly Instructions...
  • Page 46 Assembly Instructions...
  • Page 47 Assembly Instructions...
  • Page 48 Questions???... Call our Customer Service Department at 1-800-888-1232 © PlayCore Inc. 2011 Printed In USA LA 6228...

  • Page 49: Important

    Swing•N•Slide • 1212 Barberry Drive • Janesville, Wisconsin 53545 Visite nuestro sitio web en www.swing-n-slide.com o llámenos al Visitez notre site Web au www.swing-n-slide.com ou appelez-nous au...
  • Page 50 Cuando el equipo sea retirado de servicio, se debe desarmar y desechar de tal manera que no presente peligros no razonables al momento de desecharlo. ¡Importante! Instrucciones de seguridad adicionales para todos los equipos de juego Swing-N-Slide. Guardar esta hoja de instrucciones en caso de que se requiera contactar al fabricante.
  • Page 51 GARANTÍA LIMITADA DE POR VIDA DEL FABRICANTE Swing-N-Slide® garantiza que sus toboganes termoformados y montañas para escalar estarán libres de defectos de mano de obra y materiales, bajo condiciones y uso normales, durante la vida útil del producto.

  • Page 52: Iinstallation Sécuritaire - Avez-Vous

    Lorsque l’équipement est mis hors service, il doit être démonté et conditionné de sorte qu’aucun danger justifié ne sera présent lors de la mise au rebut de l’ensemble. Important! Instructions supplémentaires de sécurité pour tous les centres de jeu Swing-N-Slide. Conserver ce feuillet d’instruction au cas où vous devriez prendre contact avec le fabricant.
  • Page 53 GARANTIE LIMITÉE DU FABRICANT Swing-N-Slide® Swing-N-Slide® est fière de la qualité et de la durabilité de ses produits. Notre garantie limitée du fabricant donne l'assurance et démontre notre engagement envers la fabrication d'articles pour terrain de jeu résidentiel de qualité.
  • Page 54 LA 6229 Knights Bridge_ES_FR_- 7/27/11 4:26 PM Page 6 HERRAMIENTAS REQUERIDAS/OUTILS REQUIS HERRAMIENTAS REQUERIDAS/OUTILS REQUIS 1-1/2’’ Hex Head Bolt TALADRO ELÉCTRICO ADAPTADOR Y LLAVE DE 1/2" Y 7/16'' MARTILLO 2’’ Hex Head Bolt PERCEUSE ÉLECTRIQUE CLÉ ET DOUILLE DE 1/2 PO ET 7/16 PO MARTEAU FS 2419 WASHER 8MM...
  • Page 55 LA 6229 Knights Bridge_ES_FR_- 7/27/11 4:27 PM Page 7 Instrucciones de Ensamblaje/Instructions d’assemblage Ubicación del pliegue Emplacement des crochets (4) Pernos de carrocería de 2-1/2" (4) Boulon à carrosserie de 2 1/2 po (22) Tuercas en T de 1/4-20 (22) Écrou en T de verrouillage de 1/4-20 po (6) Pernos de cabeza hexagonal de 3/4"...
  • Page 56 RÉSERVÉ À L’UTILISATION PAR DES ENFANTS DE 2 À 10 ANS USAGE RÉSIDENTIEL/FAMILIAL SEULEMENT 1212 Barberry Drive Janesville, WI 53545 1-800-888-1232 www.swing-n-slide.com (1) Placa de identificación (1) Plaque d’identification (2) Soportes para mesa (2) Supports de table (4) Colgaderos del columpio de 5-1/4'' (4) Crochets de balançoire de...
  • Page 57 LA 6229 Knights Bridge_ES_FR_- 7/27/11 4:27 PM Page 9 Instrucciones de Ensamblaje/Instructions d’assemblage (1) Soporte para mesa (1) Mesa Discovery (1) Support de table (1) Table de découverte (1) Cristal de la ventana SQ (1) Carreau (2) Asientos de columpio Límite de peso: 115 libras (1) Del tobogán Alpine (2) Siège de balançoire...
  • Page 58 (1) [PF 3956] 1’’ x 4’’ x 41-3/8’’ (2) [PF 3705] Vigas del columpio de 2’’ x 6’’ x 94’’ PB 9241 Lista de tablas/Liste des planches (2) [PF 3705] Poutre de balançoire de 2 x 6 x 94 po (3) [PF 3955] 1’’...
  • Page 59 LA 6229 Knights Bridge_ES_FR_- 7/27/11 4:27 PM Page 11 Instrucciones de Ensamblaje/Instructions d’assemblage Cómo seleccionar el sujetador apropiado Comment sélectionner la bonne fixation Utilice estas 2 guías ilustradas para seleccionar el (los) sujetador(es) apropiado(s) para el accesorio de madera que usted está haciendo. Cada diagrama resaltará el número correcto de sujetadores que debe usarse, y dónde fijarlos.
  • Page 60 LA 6229 Knights Bridge_ES_FR_- 7/27/11 4:27 PM Page 12 Instrucciones de Ensamblaje/Instructions d’assemblage Cómo funciona el sistema de abrazaderas Comprendre le fonctionnement du système de fixation Ejemplo de una conexión con abrazadera de estante. Exemple de connecteur « Shelf-Loc ». Abrazadera de estante Connecteur «...
  • Page 61 LA 6229 Knights Bridge_ES_FR_- 7/27/11 4:27 PM Page 13 Instrucciones de Ensamblaje/Instructions d’assemblage Busque la marca “TOP” sobre las abrazaderas cuando esté realizando la instalación. Cherchez l’estampille « TOP » (DESSUS) sur les fixations pendant l’installation. NO UTILICE TORNILLOS DE COMPRESIÓN AQUÍ Use tornillos de compresión solo donde se fijan las abrazaderas N’UTILISEZ PAS ICI...
  • Page 62 LA 6229 Knights Bridge_ES_FR_- 7/27/11 4:27 PM Page 14 Instrucciones de Ensamblaje/Instructions d’assemblage Fig. 2 Tuerca en T seguridad 1/4-20 Écrou en T de Arandela plana verrouillage Rondelle plate 1/4-20 Tornillos de 3''por junta Vis de 3 po par joint Perno de cabeza hexagonal de 4”...
  • Page 63 LA 6229 Knights Bridge_ES_FR_- 7/27/11 4:27 PM Page 15 Instrucciones de Ensamblaje/Instructions d’assemblage ALINEADO Fig. 3a ALIGNÉ Fig. 3 Tornillos Vis de 3 po de 3" por par joint junta ALINEADO ALIGNÉ Vis de 2 1/2 po Tornillos par joint de 2-1/2'' por junta 1-3/4'' Tornillo de compresión de 2'' por...
  • Page 64 LA 6229 Knights Bridge_ES_FR_- 7/27/11 4:27 PM Page 16 Instrucciones de Ensamblaje/Instructions d’assemblage Fig. 4 NO UTILICE TORNILLOS DE COMPRESIÓN AQUÍ Use tornillos de compresión solo donde se fijan las abrazaderas N’UTILISEZ PAS ICI DE TIRE-FONDS Employez des tire-fonds uniquement aux points d’attache des fixations.
  • Page 65 LA 6229 Knights Bridge_ES_FR_- 7/27/11 4:27 PM Page 17 Instrucciones de Ensamblaje/Instructions d’assemblage Fig. 5 ALINEADO ALIGNÉ Tornillos de 3'' por junta Vis de 3 po par joint Consejo: Doble las abrazaderas para facilitar la 1-3/4'' (2) Tornillos de compresión de 1-1/4'' y instalación de la pieza de 2'' x 4''.
  • Page 66 LA 6229 Knights Bridge_ES_FR_- 7/27/11 4:27 PM Page 18 Instrucciones de Ensamblaje/Instructions d’assemblage Fig. 6 Tornillos de 3'' por junta Vis de 3 po par joint S 2775 FS 2791 Estructura 1 FS 2751 Tornillos de 0 ACQ 3'' por junta SCR #8X1.25 FL T20 ZINC Cadre SCR #...
  • Page 67 LA 6229 Knights Bridge_ES_FR_- 7/27/11 4:27 PM Page 19 Instrucciones de Ensamblaje/Instructions d’assemblage Fig. 7 Tornillos de 3'' por junta Vis de 3 po par joint 2775 FS 2791 FS 2751 47-1/2'' 0 ACQ SCR #8X1.25 FL T20 ZINC SCR #1 SCR #8 x 2"...
  • Page 68 LA 6229 Knights Bridge_ES_FR_- 7/27/11 4:27 PM Page 20 Instrucciones de Ensamblaje/Instructions d’assemblage Fig. 8 Tornillos de 3'' por junta Vis de 3 po par joint FS 2091 FS 2751 SCR #12X3/4" TR PNHD SCR #8 x 2" BUGLE ACQ+ Soporte de la plataforma y tablas de la plataforma FS 2750 SCR #8 X .75 FLAT PHIL SCR # 6x1 1/4"...
  • Page 69 LA 6229 Knights Bridge_ES_FR_- 7/27/11 4:27 PM Page 21 Instrucciones de Ensamblaje/Instructions d’assemblage Debe haber un espacio NOTA: nominal de 1/2'' entre las tablas de la plataforma. Fig. 9 REMARQUE : vous devez laisser un écart nominal de 1/2 po entre les planches de la plate-forme.
  • Page 70 LA 6229 Knights Bridge_ES_FR_- 7/27/11 4:27 PM Page 22 Instrucciones de Ensamblaje/Instructions d’assemblage Fig. 10 Fig. 10a ALINEADO ALIGNÉ Tornillos de 2" Vis de 2 po Tornillos de Dorso 3'' por junta Arrière Vis de 3 po par joint ALINEADO ALIGNÉ Tornillos de 2"...
  • Page 71 LA 6229 Knights Bridge_ES_FR_- 7/27/11 4:27 PM Page 23 Instrucciones de Ensamblaje/Instructions d’assemblage Fig. 11 [PF 3976] 2'' x 4'' x 34'' (4) [PF 3950] 1'' x 4'' x 34'' Tornillos Tornillos de 1-1/4'' de 2'' por junta por junta Vis de Vis de 2 po par 1 1/4 po...
  • Page 72 LA 6229 Knights Bridge_ES_FR_- 7/27/11 4:27 PM Page 24 Instrucciones de Ensamblaje/Instructions d’assemblage Fig. 12 Tornillos de 1-1/4'' por junta Vis de [PF 3935] 1'' x 4'' x 9-3/8'' 1 1/4 po par joint [PF 3950] 1'' x 4'' x 34'' [PF 3950] 1'' x 4'' x 34'' ALINEADO ALIGNÉ...

  • Page 73: Support De Poutre De Balançoire

    LA 6229 Knights Bridge_ES_FR_- 7/27/11 4:27 PM Page 25 Instrucciones de Ensamblaje/Instructions d’assemblage Fig. 13 [PF 3971] 2'' x 4'' x 31-1/4'' Fig. 13a Tuerca en T deseguridad de 1/4-20 Écrou en T de verrouillage de 1/4-20 Arandela de seguridad Rondelle de blocage Arandela plana...

  • Page 74: Construction De La Poutre De Balançoire

    LA 6229 Knights Bridge_ES_FR_- 7/27/11 4:27 PM Page 26 1-1/2’’ Hex Head Bolt Instrucciones de Ensamblaje/Instructions d’assemblage Perno de 1-1/2'' Boulon de 1 1/2 po Perno de 5-1/2'' Fig. 14 Fig. 14a Arandela Boulon de 5 1/2 po Arandela/Rondelle Rondelle Tuerca en T de seguridad de 1/4-20 Arandela Écrou en T de verrouillage de 1/4-20 Rondelle...
  • Page 75 LA 6229 Knights Bridge_ES_FR_- 7/27/11 4:27 PM Page 27 Instrucciones de Ensamblaje/Instructions d’assemblage Fig. 15 Fig. 15a Arandela de seguridad Rondelle de blocage Arandela/Rondelle Perno de 4-1/2'' Boulon de 4 1/2 po 1-1/2’’ Hex Head Bolt Tuerca en T de seguridad de 1/4-20 Perno de 2'' Boulon de 2 po Écrou en T de verrouillage...
  • Page 76 LA 6229 Knights Bridge_ES_FR_- 7/27/11 4:27 PM Page 28 Instrucciones de Ensamblaje/Instructions d’assemblage Martillo Marteau Abrazadera de la viga inferior Attache de bas de poutre Tuerca en T de 5/16'' Écrou en T Orificio de 3/8'' de 5/16 po Trou de 3/8 po Colgadero de columpio Support de balançoire Tuerca en...
  • Page 77 LA 6229 Knights Bridge_ES_FR_- 7/27/11 4:27 PM Page 29 Instrucciones de Ensamblaje/Instructions d’assemblage Fig. 16 12" 18" Fig. 16a Tuerca de seguridad Arandela Contre-écrou Rondelle (3) Tornillos de 1-1/4'' Perno con por abrazadera cabeza de (3) Vis de 1 1/4 po hongo de 2"...
  • Page 78 LA 6229 Knights Bridge_ES_FR_- 7/27/11 4:27 PM Page 30 Instrucciones de Ensamblaje/Instructions d’assemblage Fig. 17 Fig. 17a Tuerca en T de seguridad de 1/4-20 Écrou en T de verrouillage de 1/4-20 Tuerca de seguridad Contre-écrou Arandela/Rondelle Arandela/Rondelle Tuerca de seguridad Contre-écrou Perno de 4-1/2'' Boulon de 4 1/2 po...
  • Page 79 LA 6229 Knights Bridge_ES_FR_- 7/27/11 4:27 PM Page 31 Instrucciones de Ensamblaje/Instructions d’assemblage Fig. 18 Fig. 18a Fig. 18b Vis de 3 po par joint Tornillos de 3'' por junta ALINEADO ALIGNÉ Tornillos de compresión de 1-1/4'' por junta Tire-fonds Tornillos de 1 1/4 po de 2-1/2'' par joint...
  • Page 80 LA 6229 Knights Bridge_ES_FR_- 7/27/11 4:27 PM Page 32 Instrucciones de Ensamblaje/Instructions d’assemblage Consejo: Doble las abrazaderas para facilitar Fig. 19 la instalación de la pieza de 2'' x 4''. Conseil : pliez les fixations pour faciliter l’installation des poutres de 2 x 4 po Tornillos de 2'' por junta Vis de 2 po par joint Fig.
  • Page 81 LA 6229 Knights Bridge_ES_FR_- 7/27/11 4:27 PM Page 33 Instrucciones de Ensamblaje/Instructions d’assemblage Fig. 20 Tornillos de 3'' por junta Vis de 3 po par joint Fig. 20a FS 2091 FS 2751 SCR #12X3/4" TR PNHD SCR #8 x 2" BUGLE ACQ+ [PF 3951] 1'' x 4'' x 36'' Tornillos de 3'' por junta...
  • Page 82 LA 6229 Knights Bridge_ES_FR_- 7/27/11 4:27 PM Page 34 Instrucciones de Ensamblaje/Instructions d’assemblage Fig. 21 Tornillos de 3'' por junta Vis de 3 po par joint Fig. 21a Tornillos de 1-1/4'' por junta Vis de 1 1/4 po par joint (6) [PF 3953] 1'' x 4'' x 39-1/4'' Debe haber un espacio NOTA: nominal de 1/4'' entre...
  • Page 83 LA 6229 Knights Bridge_ES_FR_- 7/27/11 4:27 PM Page 35 Instrucciones de Ensamblaje/Instructions d’assemblage Fig. 22 Debe haber un espacio NOTA: nominal de 2-1/8'' entre las tablas laterales de la barrera. REMARQUE : Vous devez laisser un jeu nominal de 2 1/8 po entre Tornillos de les planches de barrière.
  • Page 84 LA 6229 Knights Bridge_ES_FR_- 7/27/11 4:27 PM Page 36 Instrucciones de Ensamblaje/Instructions d’assemblage Fig. 23 Peldaños de la escalera de 19'' Barreaux de l’échelle de 19 po 11-1/4'' 11-1/4'' Fig. 23a Perforaciones previas Pré-percé 11-1/4'' Tornillos de compresión de 2'' por peldaño Tire-fonds 14-1/2''...
  • Page 85 LA 6229 Knights Bridge_ES_FR_- 7/27/11 4:27 PM Page 37 Instrucciones de Ensamblaje/Instructions d’assemblage Fig. 24 Fig. 24a Orificios de 3/8" Trous de 3/8 po Piedra FS 2091 Pierre FS 2751 (2) Pernos de cabeza hexagonal de 1-1/4'' Boulons à tête hexagonale de 1 1/4 po SCR #12X3/4"...
  • Page 86 LA 6229 Knights Bridge_ES_FR_- 7/27/11 4:28 PM Page 38 Instrucciones de Ensamblaje/Instructions d’assemblage Fig. 25 Fig. 25a [PF 3936] Ángulo de 1'' x 4'' x 12'' [PF 3936] Cadre de 1 x 4 x 12 po 19'' Tornillos de [PF 3937] Ángulo de 1'' x 4'' x 16-7/8'' 1-1/2"...

  • Page 87: Installation Du Support De La Bâche Et De La Glissoire

    LA 6229 Knights Bridge_ES_FR_- 7/27/11 4:28 PM Page 39 Instrucciones de Ensamblaje/Instructions d’assemblage Fig. 26 Fig. 26a Arandela Rondelle 3 Per Side 3 par côté Tornillo de 3/4'' Vis de 3/4 po Fig. 26b Tornillo para madera de 1-1/4'' Vis de 1 1/4 po par planche Tornillos de 1-1/4'' por Instalación de la lona y del soporte...
  • Page 88 LA 6229 Knights Bridge_ES_FR_- 7/27/11 4:28 PM Page 40 Instrucciones de Ensamblaje/Instructions d’assemblage Fig. 27 Vis à tête bombée de 1 Vis à tête bombée de 1 po Tornillos de 1-1/4'' por junta Fig. 27a Vis de 1 1/4 po par joint Material de recubrimiento Matériau de surface...
  • Page 89 LA 6229 Knights Bridge_ES_FR_- 7/27/11 4:28 PM Page 41 Instrucciones de Ensamblaje/Instructions d’assemblage Fig. 28 Instale las abrazaderas en el centro de la tabla exterior Installez les fixations au centre de la planche extérieure 36-3/4'' 22-3/4'' Tornillos de compresión de 2'' por junta Tire-fonds de 2 po par joint Fig.
  • Page 90 LA 6229 Knights Bridge_ES_FR_- 7/27/11 4:28 PM Page 42 Instrucciones de Ensamblaje/Instructions d’assemblage Fig. 28c Fig. 28d Tornillos de compresión de 2'' por junta Tire-fonds de 2 po par joint 3/4'' ESPACIO de ambos lados Fig. 28e Joint ouvert de 3/4 po de chaque côté...

  • Page 91: Vista Interna Vue De L'intérieur

    Vis de 1212 Barberry Drive 1 1/2 po Janesville, WI 53545 1-800-888-1232 www.swing-n-slide.com VISTA INTERNA VUE DE L’INTÉRIEUR Decoración de la ventana y placa de identificación 1. Instale las tablas de decoración de la ventana como se muestra en la (Fig. 29).
  • Page 92 LA 6229 Knights Bridge_ES_FR_- 7/27/11 4:28 PM Page 44 Instrucciones de Ensamblaje/Instructions d’assemblage Manija de seguridad/Poignée de sécurité Manija de seguridad Arandela de 1/4'' Rondelles de 1/4 po 1. Monte las manijas de seguridad en los postes, aproximadamente Fig. 30 a 11'' de distancia sobre la superficie de la plataforma en las aberturas de la pared para escalar y de la escalera.
  • Page 93 LA 6229 Knights Bridge_ES_FR_- 7/27/11 4:28 PM Page 45 Instrucciones de Ensamblaje/Instructions d’assemblage Fig. 31 Fig. 31a COLUMPIO DEL “2 FOR FUN” 1. Pase las cadenas por las manijas del “2 For Fun” como se muestra en la (Fig. 31). 2.

  • Page 94: Assemblage Du Siège De La Balançoire

    LA 6229 Knights Bridge_ES_FR_- 7/27/11 4:28 PM Page 46 Instrucciones de Ensamblaje/Instructions d’assemblage Asientos de columpio/Sièges de balançoire Fig. 32a Fig. 32 Fig. 32b Ensamblaje del asiento del columpio 1. Sostener el asiento del columpio en forma vertical e introducir cadenas sin recubrimiento a través de los canales de la parte inferior del asiento del columpio.
  • Page 95 LA 6229 Knights Bridge_ES_FR_- 7/27/11 4:28 PM Page 47 Assembly Instructions...
  • Page 96 LA 6229 Knights Bridge_ES_FR_- 7/27/11 4:28 PM Page 48 ¿Alguna pregunta? Llame a nuestro Departamento de Servicio al Cliente al 1-800-888-1232 Des questions? Appelez notre division du service à la clientèle au 1 800 888-1232 © PlayCore Inc. 2011 Printed In USA LA 6229...

Table des Matières