Technical Data; Before Starting The Equipment; Assembling The Components - Royal RPM 46 Mode D'emploi D'origine

Anleitung_RPM_46_SPK7:_
GB
Bitte beachten Sie, dass unsere Geräte
bestimmungsgemäß nicht für den gewerblichen,
handwerklichen oder industriellen Einsatz konstruiert
wurden. Wir übernehmen keine Gewährleistung,
wenn das Gerät in Gewerbe-, Handwerks- oder
Industriebetrieben sowie bei gleichzusetzenden
Tätigkeiten eingesetzt wird.
The operating instructions as supplied by the
manufacturer must be kept and referred to in order to
ensure that the lawn mower is properly used and
maintained. The instructions contain valuable
information on operating, maintenance and servicing
conditions.
Important! Due to the high risk of bodily injury to the
user, the lawn mower may not be used to trim
bushes, hedges or shrubs, to cut scaling vegetation,
planted roofs, or balcony-grown grass, to clean (suck
up) dirt and debris off walkways, or to chop up tree or
hedge clippings. Moreover, the lawn mower may not
be used as a power cultivator to level out high areas
such as molehills.
For safety reasons, the lawn mower may not be used
as a drive unit for other work tools or toolkits of any
kind.

4. Technical data

Engine type:
Single cylinder four-stroke engine, 135 ccm
Engine power:
Working speed:
Fuel:
Tank capacity:
Engine oil:
Spark plug:
Electrode spacing:
Cutting height adjustment:
Cutting width:
L sound pressure level:
pA
L sound power level:
WA
Vibration a
hw
Weight:
22
16.06.2009 8:04 Uhr Seite 22

5. Before starting the equipment

5.1 Assembling the components

Some parts of the mower come disassembled. For
quick and easy assembly, read and follow the
instructions below.
Important. You will need the following additional
tools (not supplied) for assembly, and also for
maintenance work:
An open-ended wrench (10 mm)
A ring wrench (12 mm)
An open-ended wrench (13 mm)
A flat oil drip tray (for changing the oil)
A 1 liter measuring jug (oil/petrol resistant)
A petrol can (5 liters is sufficient for approx. 6
operating hours)
A funnel (suitable for the tank's petrol filler neck)
Household wipes (to wipe up oil/petrol residue;
dispose of these at a filling station)
A petrol suction pump (plastic, available from DIY
stores)
An oil can with hand pump (available from DIY
stores)
1 liter of engine oil (15W-40)
Assembling the mower
1. Take the mower and attachment parts out of the
packaging and check that all parts are present
(Fig. 2-3).
2. Attach the lower push bar (Fig. 4/Item 17) to the
mower housing using the screws (Fig. 4/Item 18)
and the nuts (Fig. 4/Item 19). Attach the upper
push bar (Fig. 5/Item 12) to the lower push bar
using the screws (Fig. 5/Item 20) and the star
2.75 kW/3.75 HP
nuts (Fig. 5/Item 21). Do not forget to mount the
3100 min -1
starter cord guide (Fig. 5/Item 22). Now hook in
petrol
the motor-stop Bowden wire (Fig. 6). Disconnect
the lever to make it easier to attach the Bowden
approx. 1.3 l
wire.
approx. 0.6 l / 15W40
3. Then hook the starter cord in the starter cord
F6TC
guide (Fig. 7)
4. Fasten the cable holder to the push bar (Fig. 8)
0.5 – 0.6 mm
with the screw (Fig. 3/Item 15).
central, (32-70 mm)
5. Fasten the cords to the push bar with one of the
460 mm
cable ties (Fig. 3/Item 16), as shown in Fig. 9.
6. Lift the ejector flap with one hand and hook the
76 dB(A)
grass basket into the mounts on the housing (Fig.
96 dB(A)
14)
2.56 m/s 2
33.5 kg