Technical Data; Before Starting The Engine; Assembling The Components - Royal RPM 56 S-MS Instructions De Montage Et Mode D'emploi

Anleitung_RPM_56_S_MS_SPK7__ 08.05.12 16:34 Seite 22
GB
Please note that our equipment has not been
designed for use in commercial, trade or industrial
applications. Our warranty will be voided if the
machine is used in commercial, trade or industrial
businesses or for equivalent purposes.
The operating instructions as supplied by the
manufacturer must be kept and referred to in order to
ensure that the lawn mower is properly used and
maintained. The instructions contain valuable
information on operating, maintenance and servicing
conditions.
Important! Due to the high risk of bodily injury to the
user, the lawn mower may not be used to trim
bushes, hedges or shrubs, to cut scaling vegetation,
planted roofs, or balcony-grown grass, to clean (suck
up) dirt and debris off walkways, or to chop up tree or
hedge clippings. Moreover, the lawn mower may not
be used as a power cultivator to level out high areas
such as molehills.
For safety reasons, the lawn mower may not be used
as a drive unit for other work tools or toolkits of any
kind.

4. Technical data

Engine type:
Single cylinder four-stroke engine, 173 ccm
Working speed:
Fuel:
Tank capacity:
Engine oil:
Spark plug:
Electrode spacing:
Cutting height adjustment:
Cutting width:
L sound pressure level:
pA
L sound power level:
WA
Vibration a
hw
Weight:
22

5. Before starting the engine

5.1 Assembling the components

Some parts of the mower come disassembled. For
quick and easy assembly, read and follow the
instructions below.
Important! You will need the following additional
tools (not supplied) for assembly, and also for
maintenance work:
A flat oil drip tray (for changing the oil)
A 1 liter measuring jug (oil/petrol resistant)
A petrol can (5 liters is sufficient for approx. 6
operating hours)
A funnel (suitable for the tankʼs petrol filler neck)
Household wipes (to wipe up oil/petrol residue;
dispose of these at a filling station)
A petrol suction pump (plastic, available from
DIY stores)
An oil can with hand pump (available from DIY
stores)
1 liter of engine oil (10W30)
Assembly
1. Take the mower and attachment parts out of the
packaging and check that all parts are present
(Fig. 2).
2. Fasten the push bar using a square head screw
(Fig. 3a/Item 15) and a star screw (Fig. 3a/Item
18) on each side. For fastening choose one of
the three holes to suit the required height of the
handle. Important. The identical height must be
set on both sides. Ensure that the cords which
2800 min -1
are fastened later are not in the way.
standard petrol
3. Fasten the top push bar to the bottom push bar
approx. 2 l
using a screw (Fig. 3b/Item 16) and a star screw
(Fig. 3b/Item 18) on each side. Make sure that
approx. 0.6 l / 10W30
the lobes of the screws (16) are folded towards
F6RTC
the inside so that the high speed clamping
0.5 – 0.6 mm
function remains operational.
4. Insert the grip of the starter cord (Fig. 3c/Item 4)
central, (30-75 mm)
into the hook provided for that purpose (Fig.
560 mm
3c/Item 24) as shown in Figure 3c.
90,1 dB(A)
5. Fasten the cords to the push bar with the
supplied cable ties (Fig. 3d/Item. 13).
98 dB(A)
6. Lift the ejector flap (Fig. 4 / Item 8) with one hand
7.3 m/s 2
and hook in the grass bag (Fig. 4/Item 7) as
46 kg
shown in Figure 4