Peg-Perego primonido new Culla Notice D'emploi page 18

• Do not iron.
• Do not dry clean.
• Do not remove stains with solvents and do not tumble dry.
Product cleaning
• This product requires a small amount of maintenance.
Cleaning and maintenance must only be carried out by adults.
• Keep all moving parts clean and if necessary lubricate
them with light oil.
• Clean the plastic parts periodically with a damp cloth. Do
not use solvents or similar substances.
• Brush the fabric parts to remove dust.
• Do not clean the polystyrene shock absorbing device with
solvents or other similar products.
• Protect the product from atmospheric agents: humidity,
rain or snow. Extended exposure to sunshine can cause
colour changes in many materials.
• Store the product in a dry environment.
• Remember to regularly ventilate the interior of the carrycot.
Car Kit
How to fit the safety harness
11• Fit the pram with the backrest and hood lowered.
12• 3-POINT SAFETY HARNESS: Pass the leg divider straps
through the slot in the mattress pad (fig_a) and the slots
in the shell (fig_b) so that they come out on the other side
(fig_c).
13• Pass the two ends of the shoulder straps through the slots
in the mattress pad and the shell (fig_a), then clip them to
the pins (fig_b).
14• Straps attached under the shell (fig_a) and inside the pram
(fig_b).
Attachment in vehicles with safety belts
ATTACHING THE PRAM UNIT IN VEHICLES: It is possible to
install the pram in cars if there are 3 rear seats with 3 safety
belts. The central one can be 3-point or a lap belt.
We recommend positioning the pram on the vehicle's rear
seats with the end for the child's head above the central seat.
15• The pram fitted in a vehicle with a lap belt.
16• The pram fitted in a vehicle with a 3-point belt.
17• The pram can also be positioned in the centre of a
3-person rear seat, using the two outer safety belts (fig_a).
It cannot be positioned as in fig_b because it can only
be secured in vehicles using safety belts that come from
opposite sides.
18• Position of the pram on a 2-person rear seat. The pram can
be positioned with the child's feet on either side of the
vehicle. If the seat of the vehicle inclines, towels can be
used to provide a horizontal surface.
19• Take the rear seat belt, fold it as shown in the figure
(arrow_a) and insert it in the slot of the car kit's metal
fastener (arrow_b).
20• Insert the red lever on the metal fastener of the car kit inside
the folded belt (arrow_c).
Move the metal fastener as near as possible to the seat in
order to enable it to be fastened to the Carrycot (arrow_d).
21• Hook the car kit connector to the ring on the Carrycot and
pull firmly on the belt to ensure the Carrycot fits as well as
possible to the seat.
• Repeat the same operations on the other side of the
Carrycot.
22• Car Carrycot installed in the car.
23• UNFASTENING THE CARRYCOT FROM THE CAR:
press the control button on the connector to loosen the
belts, as shown in the figure. Unhook the fastener of the car
kit connector from the ring on the Carrycot.
IMPORTANT: the car kit can remain fastened to the
seat belts of your car. The car kit fastener can easily be
attached to or removed from the ring on the Carrycot
(point 22).
IMPORTANT: do not leave the car kit fastened onto the
vehicle's safety belt when this is being used by an adult.
How to put the child in the pram
24• 3-POINT SAFETY HARNESS: Slacken the straps by pressing
on the buckle (fig_a) and lengthen them (fig_b).
25• Press the red button (fig_a) and release the straps from the
leg divider (fig_b).
26• Place the child in the pram then buckle together the straps
and the leg divider.
18