Selecting The Surround Field; Maintenance; Troubleshooting Guide - Panasonic RP-WF6000 Mode D'emploi

Listening to audio from equipment connected to the transmitter
If the sound is broken or noisy when the headphones are in use
(Setting the most appropriate frequency)
The sound may be broken or noisy if the headphones are used outside the range of the radio waves or if
the reception becomes poor due to the interference from other wireless equipment using the 2.4 GHz radio
frequency band, a microwave etc.
Perform the following steps to manually reset the appropriate frequency for transmitting.
Press [ID/TUNING] on the transmitter once.
● The ID/TUNING lamp on the transmitter glows green, the
transmitter changes the frequency and then radio waves
start being transmitted.
● The headphones will automatically detect the emitted
frequency and noise and sound distortion will stop.
When the noise or sound distortion does not stop
Repeat the above step until the most appropriate frequency is set.
● This may not solve the problem if the headphones are being affected by a digital cordless telephone or other
device. In this case, moving the transmitter and the headphones as far as possible from the digital cordless
telephone or other device may stop the noise or sound distortion.
Selecting the surround field
Press [SURROUND] to select the desired surround
mode.
Each time the button is pressed
● The SURROUND lamp for the selected mode will come on.
● This will go off, if "OFF" is selected.
● If the AC adaptor is disconnected and then connected, CINEMA is
automatically selected.
Surround mode Surround mode and suitable input source
OFF For normal headphone play
MUSIC When playing music sources for enhanced acoustics
When playing movie sources for greater audio impact
CINEMA
Creates a feeling close to being actually part of the scene
When playing sports game sources
VOICE Reproduces the excitement of being in a stadium at a noisy sports scene while making
the sound of the announcer or commentator easier to hear.
For your reference
● Depending on the signal being input, volume may vary when changing between surround modes.
● There is no surround effect when playing a monaural source.

Maintenance

To clean this unit, wipe with a soft, dry cloth.
● Never use alcohol, paint thinner, or benzine to clean this unit.
16
● Before using chemically treated cloth, read the instructions that came with the cloth carefully.
16

Troubleshooting guide

Before requesting service, make the below checks. If you are in doubt about some of the check points, or if the
remedies indicated in the chart do not solve the problem, consult your dealer for instructions.
Take both the headphones and the transmitter when you visit your dealer.
Problem Possible cause and suggested remedy
No sound.
y Check that the AC adaptor is connected to the transmitter (
y Check that the transmitter and the AV equipment are connected
( page 11 to 12).
y Turn on the AV equipment connected to the transmitter and start play on it. Check
that the OPR/CHARGE lamp on the transmitter lights green (
y Check that the transmitter's INPUT SELECT control is set correctly for the connected
equipment ( page 14).
y If the transmitter is connected to the headphone jack, turn up the volume on the
connected equipment (
y Put the headphones on again.
y Turn up the volume on the headphones (
y The MUTING function is activated (
● Move into the range of the radio waves.
y The headphones' OPR lamp is not on (
● The supplied rechargeable battery has run down. Recharge them or replace the
alkaline dry cell batteries with new ones. If the OPR lamp is still off, take the unit to
your dealer.
y Set the digital output setting on the connected equipment to "ON" if digital input is
selected.
y You are playing a DTS audio track on a DVD player that is not compatible with DTS
( page 12).
● Use a DTS compatible DVD player or select a PCM or Dolby Digital track.
y You are playing a DVD recorded in DTS audio on a DVD player (includes game
machines) when "OFF" has been selected for the DVD player's DTS digital output
setting ( page 12).
● Set the DVD player's DTS digital output setting to "ON".
y You are playing a DVD recorded in DTS audio on a DVD player (includes game
machines) connected to this unit with an analogue connection (
page 8).
page 14).
page 12).
page 14).
page 15).
page 10).
page 12).
17
17