Publicité
PIECES AILES
(A) Aile (avec aileron et volet montés sur charnières et à coller) ................. (G/D)
............................................................................................................. 1 de chaque
(B) Tringlerie ailerons et volets (tige filetée M3) ..................................................4
(C) Chape rotule avec visserie (vis M3x15+écrou nylstop+rondelle) ......... 4 sets
(D) Guignol ailerons et volets ........................................................................ 4 sets
(E) Clé d'aile (tube carbone Ø40x1100mm) ........................................................1
(F) Vis fixation d'aile (plastique M6x25mm) .........................................................4
PIECES EMPENNAGES DIRECTION
(A) Empennage horizontal ................................................................................... 1
(B) Dérive .............................................................................................................. 2
(C) Fixation dérive (vis M4x25mm+ rondelle) .............................................. 4 sets
(D) Barre de renfort dérive................................................................................... 2
(E) Fixation barre de renfort dérive (vis M3x22mm+écrou M3 + 2 vis
M3x15mm+4rondelles) ................................................................................ 2 sets
(F) Fixation servo direction (1 carénage plastique+
2 blocs bois dur+4 vis à bois 2,2x12mm) ................................................... 2 sets
(G) Tringlerie de direction (tige filetée M3+ 2 chapes M3+écrou) ............. 2 sets
(H) Guignol direction ..................................................................................... 2 sets
PIECES EMPENNAGES PROFONDEUR
(A) Téton Ø6mm .................................................................................................... 2
(B) Carénage de stab ............................................................................................ 1
(C) Tringlerie profondeur (tige filetée M3) ............................................................2
(D) Chape rotule avec visserie (vis M3x15mm+écrou nylstop+rondelle) ... 2 sets
(E) Guignol profondeur .................................................................................. 2 sets
(F) Fixation empennage horizontal (vis M4x40mm + rondelle) ................... 2 sets
WINGS PARTS
(A) Wing (with aileron and flap installed on their hinge point to be glued) ....(L/R)
...................................................................................................................... 1 each
(B) Ailerons and flaps pushrod (M3 threaded rod)
............................................................................................................................... 4
(C) Ball clevis with screws (M3x15 screw+lock nut+washer) ..................... 4 sets
(D) Ailerons and flaps control horn .............................................................. 4 sets
(E) Wing joiner (Ø40x1100mm carbon tube) .......................................................1
(F) Wing screw attachment (plastic M6x25) .........................................................4
EMPENNAGES PARTS RUDDER
(A) Horizontal empennage ................................................................................... 1
(B) Fin and rudder ................................................................................................ 2
(C) Fin fixing (screw M4x25mm+washer) .................................................... 4 sets
(D) Fin reinforcement bar ...................................................................................... 2
(E) Fin reinforcement bar fixing (screw M3x22mm+nut M3 + screw
M3x15mm+4 washers) ................................................................................ 2 sets
(F) Rudder servo fixing (1 plastic cover+2 hard wood blocks+4 tapping screws
2,2x12mm) .................................................................................................... 2 sets
(G) Rudder pushrod (M3 threaded rod + 2 M3 clevis+nut) ....................... 2 sets
(H) Rudder control horn ................................................................................ 2 sets
EMPENNAGES PARTS ELEVATOR
(A) Ø6mm dowel .................................................................................................... 2
(B) Stab cover ....................................................................................................... 1
(C) Elevator pushrod (M3 threaded rod) ..............................................................2
(D) Ball clevis with screws (M3x15mm screw+lock nut+washer) ............... 2 sets
(E) Elevator control horn .............................................................................. 2 sets
(F) Horizontal empennage fixing (screw M4x40mm + washer) ................... 2 sets
170
CONTENU DU KIT
PIECES CROCHET DE REMORQUAGE
(A) Crochet de remorquage
(crochet+tige un bout fil.+chape M2+4 vis M3x15mm+4 rondelles) .........1 set
PIECES TRAIN D'ATTERRISSAGE
(A) Train avant amorti (avec amortisseur à gaz et axe de roue) .......................1
(B) Fixation train avant (vis M5x30mm) ...............................................................4
(C) Tringlerie dirigibilité (avec chapes et silent-bloc 'Servo-Saver") .............1 set
(D) Train principal.................................................................................................. 2
(E) Fixation train principal (vis M5x35mm+écrou nylstop M5) .................... 4 sets
(F) Axe de roue train principal (avec 4 bagues d'arrêt de roue) ................. 2 sets
(G) Train principal .................................................................................................. 2
(H) Roue Ø176mm ................................................................................................ 1
(I) Roue Ø210mm ................................................................................................. 2
PIECES MOTEUR
(A) Fuselage ......................................................................................................... 1
(B) Capot moteur .................................................................................................. 1
(C) Fixation capot moteur (vis M3x8 + rondelle spéciale anti-desserrage) ........6
(D) Réservoir 1500cc ........................................................................................... 2
(E) Tringlerie des gaz (avec chapes) .............................................................. 1 set
PIECES VERRIERE
(A) Verrière (ajustée sur son baquet-cabine) .......................................................1
(B) Fixation cabine (vis M3x15mm+rondelle spéciale anti-desserrage) ..... 4 sets
(C) Fixation verrière (vis à bois 2x8mm) ............................................................12
KIT CONTENT
REMOTE TOWING HOOK PARTS
(A) Remote towing hook
(hook+one side thread. rod+M2 clevis+4 M3x15mm screws+4 washers)
......................................................................................................................... 1 set
LANDING GEAR PARTS
(A) Nose gear (with gas shock and wheel axis) ...................................................1
(B) Nose gear fixing (M5x30mm screw) ...............................................................4
(C) Steering pushrod (with clevises and "Servo-Saver" device) ...................1 set
(D) Main gear ........................................................................................................ 2
(E) Main gear fixing (M5x35mm screw+M5 lock nut) .................................. 4 sets
(F) Main gear wheel axis (with 4 wheel stoppers) ........................................ 2 sets
(G) Main gear ........................................................................................................ 2
(H) Ø176mm wheel ............................................................................................... 1
(I) Ø210mm wheel ............................................................................................... 2
ENGINE PARTS
(A) Fuselage ......................................................................................................... 1
(B) Engine cowl ..................................................................................................... 1
(C) Engine cowl fixing (screw M3x8 + special washer) ........................................6
(D) 1500cc gasoline tank ..................................................................................... 2
(E) Throttle pushrod (with clevises) ............................................................... 1 set
CANOPY PARTS
(A) Canopy (fitted on its frame) ............................................................................ 1
(B) Canopy frame fixing (M3x15mm screw+special washer) ....................... 4 sets
(C) Canopy fixing (2x8mm self-tapping screw) ...................................................12
7
Publicité
