Krick Ro Marin Happy Hunter Notice De Montage Et De Mise En Œuvre page 45

- Make one ladder for the main mast and one for the
foremast. Solder overlength pieces of brass wire to
them to form the spacer pins 393, then shorten them
to 4 mm. The ladders are not required until the masts
have been assembled.
- Drill holes in the deck lamps 394, bend the deck lamp
stands 395 to shape and glue them in the holes. Drill
1 mm Ø holes in the deck and glue the deck lamps in
the holes and to the handrail.
Light shaft, return pulleys, stern lamp console, lifeb-
elts, gangway, liferaft support
- Attach the brass wire latches 397 to the light shaft
396, and glue the glazed porthole 398 in place. Glue
the completed light shaft to the boat deck.
- Fit the pulleys 400 and washers 401 on the pulley
consoles 399, but glue the washers in place only - not
the pulleys.
The foremast, Figs. 182 - 185, Plan II
Part Description
No.
409 Foremast
410 Cradle
411 Foremast strut
412 Yard block
413 Angled yard block
414 Ship's bell bracket
415 Ship's bell
- Glue together the injection-moulded parts 409 - 413 to
form the foremast, following the sequence of the part
numbers.
- Hold the prepared ladder against the foremast, mark
the position of the pins 393, and drill 1 mm Ø holes at
the marked points. Glue the ladder in the holes.
The mainmast, Figs. 186 - 191, Plan II
Part Description
No.
416 Platform
417 Railing stanchion
418 Rail
419 Rail
420 Lower mast section
421 Radar plinth
422 L.H. mast strut
423 R.H. mast strut
424 Radar platform
425 Mast
426 Navigation frame stand
427 Navigation frame
428 Lower signal yard
429 Yard block
430 Upper signal yard
431 Aerial rod
432 Aerial base
433 Aerial cap
434 Foghorn
435 Signal yardstrut
436 Radar arm
Material
ABS
ABS
ABS
ABS
ABS
Brass
Brass
Material
ABS
Brass
Brass
Brass
ABS
ABS
ABS
ABS
ABS
ABS
ABS
ABS
ABS
ABS
ABS
Brass
ABS
Glass
Plastic
Brass
ABS
© Klaus Krick Modelltechnik, Germany, Stand 06.2017
- Glue the pulley consoles and the lamp console 402 in
place as shown on the plan. The method of fitting the
stern lamp is described in the "Lighting" section.
- Glue the two-part liferafts 403 together.
- Bend the four catapult arms 404 to shape. We recom-
mend that you make a simple jig for bending these
parts.
- Solder the catapult feet 405 to the catapult arms, and
solder the catapult struts 406 in place.
- Glue the catapults and the liferafts to the superstruc-
ture.
- Attach the lifebelts 407 to the superstructure.
- Make up the gangway from the braces 408 and the
lengths of brass wire 408a, and glue it to the rear of
the superstructure.
Size in mm
Inj. moulded
Inj. moulded
Inj. moulded
Inj. moulded
Inj. moulded
0.7 Ø
Ready made
- Bend to shape the bracket 414 for the ship's bell
415. Drill a 0.7 mm Ø hole, glue the bracket in it, and
attach the ship's bell.
- Drill a 2 mm Ø hole in the superstructure and glue the
foremast in it.
Size in mm
Inj. moulded
25 high, 3 holes
0,7 Ø
0.7 Ø
Inj. moulded
Inj. moulded
Inj. moulded
Inj. moulded
Inj. moulded
Inj. moulded
Inj. moulded
Inj. moulded
Inj. moulded
Inj. moulded
Inj. moulded
1 Ø x 140
Inj. moulded
3.5 O.D.
Inj. moulded
0.7 Ø x 20
Inj. moulded
No. Notes
off
1
5
1
2
2
1 As plan
1 FS
No. Notes
off
1
9 FS
1 As plan
2 As plan
1
1
1
1
1
1
1
1
1
9
1
1
1
1 FS, bead
2 FS
2
2 FS
21