Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
Crane outrigger mechanism
Part
Description
No.
131
Base plate
132
Motor support
133
Motor, geared 1000 : 1
134
End-support
135
End-support
136
Worm gear shaft
137
Worm gear
138
Grubscrew with cutter tip
139
Coupling sleeve
140
Side panel
141
Drive shaft
142
Collet
143
Grubscrew
144
Bevel gear
Refer to the detail drawing on Plan I and photos 96 and
97.
- Glue the motor support 132 to the base plate 131 at
rightangles, and install the motor 133.
- Assemble the lower drive unit 134 - 139, engage it,
align it carefully and glue the end-supports 134 and
135 to the base plate.
Hook mechanism
Part
Description
No.
145
Mounting plate
146
Motor flange
147
Gusset
148
Motor, geared 400 : 1
149
Actuating disc
Refer to the detail drawing on Plan I and photos 98 and
99.
Anchor winch mechanism
Part
Description
No.
150
Mounting plate
151
Chain drum disc
152
Drum hub
153
Collet
154
Grubscrew
155
Axle
156
Base plate
157
Motor flange
158
End-support
159
Side panel
160
Gusset
161
Motor, geared 400 : 1
162
Coupling sleeve
163
Self-tapping screw
Refer to the detail drawing on Plan I and photos 100 to
102.
- Glue the discs 151 centrally to the drum hub 152.
10
Material
ABS
ABS
---
ABS
ABS
Brass
Brass
Steel
Plastic
ABS
Brass
Brass
Steel
Brass
Material
ABS
ABS
ABS
---
Aluminium
Material
ABS
ABS
Plastic
Brass
Steel
Brass
ABS
ABS
ABS
ABS
ABS
---
Plastic
Steel
© Klaus Krick Modelltechnik, Germany, Stand 06.2017
Size in mm
1.5, laser-cut
1.5, laser-cut
---
1.5, laser-cut
1.5, laser-cut
2 Ø x 43
10 Ø
M3 x 3
1.0 I.D. x 18
1.5, laser-cut
4 O.D. x 45
4 I.D.
M3 x 3
11.2 Ø
- Fit the drive unit and the spur gear 144 together, fit it
on top and align it carefully. Ensure that the spur gear
engages centrally with the worm gear.
- Glue the side panels 140 to the base plate.
- Drill a 1 mm Ø hole in the drive shaft 141.
Size in mm
1.5, laser-cut
1.5, laser-cut
1.5, laser-cut
---
16 Ø
- Assemble the motor bracket from parts 145 - 147 and
glue the joints.
- Fit the motor 148 and the actuating disc 149, 138.
Size in mm
1, laser-cut
1.5, laser-cut
15 x 13 x 20
2 I.D.
M3 x 3
2 Ø x 55
1.5, laser-cut
1.5, laser-cut
1.5, laser-cut
1.5, laser-cut
1.5, laser-cut
---
1 I.D. x 20
2.9 Ø x 9.5
- Fit the axle 155 so that the collets 153, 154 can be po-
sitioned accurately; glue the collets to the discs only.
- Glue the base plate 156 to the motor support, install
the motor 161 and fit the end-supports 158 on the an-
chor drum unit. Couple the parts using the sleeve 162
No.
Notes
off
1
plate 6
1
plate 4
1
Not included
1
plate 3
1
plate 4
1
1
FS
5
FS
1
2
plate 2
1
Tubular rivet
2
2
1
FS
No.
Notes
off
1
plate 3
1
plate 3
2
plate
1
Not included
1
No.
Notes
off
1
plate 7
2
plate 6
1
2
2
1
1
plate 3
1
plate 3
2
plate 3
2
plate 2
2
plate 3
1
Not included
1
2
Publicité
Table des Matières
