Krick Ro Marin Happy Hunter Notice De Montage Et De Mise En Œuvre page 44

Fitting out the removable hatch, Figs. 173 - 175, Plan II
Part Description
No.
378 Boiler pipe
379 Boiler end panel
380 Boiler end panel
381 Instrument panel
382 Instrument panel support
383 Boiler support
384 Boat support
385 Inflatable boat
385 A Inflatable boat transom
386 Transport bar
- Fit the boiler end panels 379 and 380 on the boiler pipe.
Glue the instrument panel 381, 382 to the boiler. Place
the boiler on the boiler supports 383, and glue this as-
sembly on the hatch.
- Glue transom 385 A to the back of inflatable boat 385.
- Glue the supports 384 for the inflatable boats 385 on the
hatch and the boat deck 320. Glue the front inflatable
boat in place.
Deck and superstructure fittings, Figs. 176 - 181, plans I and II
Part Description
No.
387 Outrigger support
388 Brace
389 Lamp plinth
390 Lamp mast
391 Companionway
392 Ladder
393 Spacer pin
394 Deck lamp
395 Deck lamp stand
396 Light shaft
397 Latch
398 Glazed porthole
399 Pulley console
400 Return pulley
401 Washer
402 Lamp console
403 Liferaft
404 Catapult arm
405 Catapult foot
406 Catapult strut
407 Lifebelt
408 Gangway brace
408a Gangway grid
Outrigger support and stern light
- Assemble the outrigger support from parts 387 and
388, and glue it in the 3 mm Ø hole in the removable
hatch.
- Remove the cylindrical spigot from the lamp plinth
389. Sand the rear corners as shown, and glue the
plinth to the tube 390.
- Glue the tube in the 3 mm Ø hole, ending flush on
the underside. The method of fitting the stern lamp is
described in the section entitled "Lighting".
20
Material
Metal
Resin casting
Resin casting
ABS
ABS
ABS
ABS
Resin casting
ABS
Brass
Material
Brass
Brass
ABS
ABS
Plastic
Brass
Brass
Aluminium
Brass
ABS
Brass
Brass
ABS
Aluminium
Brass
ABS
Plastic
Brass
Brass
Brass
Plastic
ABS
Brass
Companionways, ladders and deck lamps
© Klaus Krick Modelltechnik, Germany, Stand 06.2017
Size in mm
22 Ø x 59
1, laser-cut
1, laser-cut
3, machined
1.5, laser-cut
1.5, laser-cut
1 Ø x 80
- Drill two 1 mm Ø holes at the balance point of the
rear inflatable boat to accept the transport bar 386 as
shown in the detail view. Bend the bar to shape and
insert it in the holes.
- The purpose of the bar is to enable the crane to raise
the inflatable boat and lower it to the water. But the
boat is not floatable. Place the inflatable boat on the
boat supports.
Size in mm
0.2 x 3 x 17
2.2 Ø x 3 Ø x 42
Inj. moulded
3 x 3 x 45
Overlength
Overlength
1 Ø
Machined
1 Ø
Inj. moulded
1 Ø
6 Ø x 8 Ø
Inj. moulded
Machined
2.2 I.D.
Inj. moulded
Inj. moulded
1.5 Ø
1.5 Ø
1.5 Ø
20 Ø
1 laser-cut
1 Ø x 90
- Cut the six companionways 391 to length as shown
on the plan, bevel their front faces and glue them in
place. The companionways on the removable hatch
should be glued to the edge of the hatch only; don't
glue them to the deck.
- Cut five ladders 392 to length for fitting to the super-
structure, the wheelhouse and the aft bulkhead. Bend
them as required, drill 1 mm Ø holes for them and
insert them in the holes. The ladders should not be
glued in place until the railings have been completed.
No. Notes
off
1
1
1
1 plate 7
2 plate 7
2 plate 10
4 plate 5
2 FS
2 plate 5
1
No. Notes
off
1
1
1
1
6 As plan
7 As plan
8 As plan
2 FS
2 As plan
1
2 As plan
1
4
4
4
1
2 FS
4 As plan
4 As plan
2 As plan
8 FS, inj. moulded
8 plate 7
7