Krups XP4000 Mode D'emploi Et Garantie page 7

Remove any ground coffee from around
•
the top rim of the filter handle to create a
good seal to the brewing head.
Replace the filter holder into the machine.
•
Turn the filter holder until it is firmly locked
into place (6) (7).
Place one or two espresso cups beneath
•
the filter holder.
As soon as the appliance reaches the cor-
rect temperature the orange indicator light
will go out.
Then turn the selector to the
•
(10). Take the pre-brewing into account.
When the cups are full, reset the selector
•
to the O setting.
Remove the filter holder and the filter
•
from the machine, and take out the coffee
grounds (13). Use caution not to acciden-
tally discard the filter basket.
Put the filter holder with the empty filter Put the filter holder with the empty filter
•
in place (6) (7) and push the brew button
to purge and clean the filter of coffee
sediment.
The filter basket can be refilled to make
more espressos.
Caution: if the water container is empty
and the pump is running, you will hear a
very distinct noise, which is louder than
the normal operating sound. If this hap-
pens, turn the machine "off". Check the
water container and refill as needed.
Never let the pump run when the water
container is empty as this can damage
the pump.
If you are preparing more than one cup of
espresso, disregard the orange thermostat
light. It simply indicates that the thermostat
is regulating the temperature.
W
ith the special
"ESE", which stands for "Easy Serving
Espresso", is a selected measure of coffee,
ground and pressed between two filter
papers making a coffee pod which is ready
to use (for example "illy  pods). This sys-
tem makes it easy for you to prepare your
espresso and to clean the machine.
The E.S.E. system was designed for making
Italian-style "espresso ristretto" or "short
espresso". The amount of coffee is about
two ounces and the water should take
10
setting (9)
" e.s.e. "
filter
20 seconds to run through.
We do not intend, or recommend, that
the E.S.E. servings are used for making
more then one single serving or a "long
espresso".
We recommend that you take care when
handling and storing the E.S.E. servings so
that they do not become deformed.
For best results, we recommend that you
pre-heat the accessories (filter holder, filter
basket and cups) without any coffee. To do
this, see section entitled "espresso function"
above.
. Preparing an espresso:
• Fill the water tank (1) (2) (3) and start the
appliance (4).
Place the serving of "illy  in the ESE filter
holder fitted with its own filter. The wording
"illy  must be pointing towards the bottom.
Setting the ESE pod (17).
Tear excess paper from pod at perforated
edge. Place the ESE pod with the RED
MARKING FACE DOWN (bend the paper
corners down).
• Take care to put all the paper inside the
filter or you will have some drips.
Placing the ESE pod correctly will create a
richer, thicker crema.
LOCKING the handle TIGHTLY and PRO-
PERLY will avoid leakage from the filter
holder and ensure a better brewing cycle.
Place the filter holder inside the brewing
head and FIRMLY turn the handle as far
RIGHT as possible.
Once the appliance reaches the correct
temperature, the orange temperature control
light will go out.
Then turn the selector to the setting
•
(9). Take the pre-brewing into account.
When the recommended quantity of coffee
•
has been reached (about two ounce) turn
the selector to the O position.
Remove the filter holder from the brewing
head and throw away the used coffee pod.
• Put the filter holder with the empty filter in
place (6) (7) and push the brew button to
purge and clean the filter of coffee sediment.
NOTE: Other pods (such as those sold by
Starbucks ) can be used in your Krups