Description Of Symbols - Silverline 250482 Manuel D'utilisation

GB
Introduction
Thank you for purchasing this Silverline tool. This manual contains information necessary
for safe and effective operation of this product. This product has unique features and, even if
you are familiar with similar products, it is necessary to read this manual carefully to ensure
you fully understand the instructions. Ensure all users of the tool read and fully understand
this manual.

Description of Symbols

The rating plate on your tool may show symbols. These represent important
information about the product or instructions on its use
Wear hearing protection
Wear eye protection
Wear breathing protection
Wear head protection
Read instruction manual
Caution!
Conforms to relevant legislation and safety standards
1105
Notified body number
Carefully read and understand these instructions and any label
attached to the tool before use. Keep these instructions with the product
for future reference. Ensure all persons who use this product are fully
acquainted with these instructions.
Specification
Model:......................................... . . . . . . . . . . . . . . . . . . . 250482
Applicable standards:. . . . . . . . . . . . . . . EN 361:2002 (Full Body Harness),
Purpose: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Fall arrest
Material: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Polyester
Maximum strength: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16kN
Temperature range: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .-40 to +80°C
Attachment points: . . . . . . . . . . . . . . . . . . . .EN361: Dorsal (A), Sternal (A/2)
Max. user weight: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .140kg*
Net weight:. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.90kg
As part of our ongoing product development, specifications of Silverline
products may alter without notice.
*The operator must be able to achieve a safe and comfortable fit, using the
adjustment options provided. The equipment must not be used if it cannot be
adjusted to fit the operator comfortably and securely.
6
BS EN 365:2004 (General Requirements)
2016/425/EU
Safety Instructions for Height
Safety Equipment
WARNING: Activities involving the use of this equipment are inherently
dangerous. ALWAYS carry out a risk assessment before work commences,
including rescue arrangements.
WARNING: Specific training is essential before using this equipment. It
must only be used by competent and responsible individuals, taking care not
exceeding the limitations of the equipment.
WARNING: Failure to adhere to any warnings and recommendations given
in these instructions, may result in severe injury or even death! When using this
equipment you personally assume all risks and responsibilities for all damage,
injury or death which may occur during or following incorrect use of this
equipment. You are responsible for your own actions and decisions.
If you are unable, or not in a position to assume this responsibility or to
accept these risks, DO NOT USE THIS EQUIPMENT.
a) NEVER use equipment that has exceeded its shelf and/or service life.
b) This product MUST NOT be stressed beyond its strength rating.
c) DO NOT use components of fall arrest gear outside its limitations, or
for applications which they were not specifically designed for.
d) Avoid impacts and rubbing against abrasive surfaces during use,
transport and storage.
e) DO NOT use connectors with manual locking mechanisms in areas
where they are frequently opened and closed.
f) Ensure locking mechanisms and safety devices engage securely and
connectors are fully closed and locked before use.
g) NEVER combine components that are not recommended by the
manufacturer as being compatible. One item may interfere with the safe
function of another, jeopardising the function of the system as a whole.
h) NEVER attach a fall arrest system to an anchorage if you are unsure
about the strength and condition of the anchorage.
i) Take into account the length of every single component of a fall arrest
system, including the connectors, when determining the total length
of the system.
j) The clearance under the user must be sufficient to prevent them from
striking an obstacle in the event of a fall.
k) DO NOT allow any part of a fall arrest, work positioning or restraint
system to come into contact with sharp edges or abrasive surfaces
during use. Reposition if necessary or choose an alternative anchorage.
l) Any component of a fall arrest system must be individually inspected
according to the manufacturer's recommendations and procedures.
After assembly, the system must b e inspected as a functional unit.
m)Any kind of repair or modification of this equipment is strictly
PROHIBITED.
n) DO NOT tie knots in harnesses, lanyards and ropes. DO NOT allow
equipment to become tangled.
o) Equipment that has been exposed to extreme conditions, failed
an inspection or has been used to arrest a fall must be retired and
destroyed. Never expose items made with synthetic fibre components to
direct flames.
p) DO NOT use shock absorbers that have been partially deployed, or
when the plastic sheath is damaged.
q) Destroy retired equipment immediately, to prevent further use.
r) All users of fall arrest gear must be medically fit for activities at height
and must wear appropriate personal protective equipment for the
environment, work carried out and tools used.
s) Carry out a risk assessment for every activity, and define a rescue plan
that can be safely and rapidly executed in case of emergency.
t) All product markings must remain intact and clearly legible for the
entire service life of this equipment.
u) Store the equipment with its dedicated service record and usage
instructions. Gear with uncertain service history must be removed from
service and destroyed.
v) Before using this equipment, ensure that it complies with local
federal regulations and other applicable safety standards.
w) Textile products including webbing and ropes MUST NOT be marked
using ink from marker pens or paint, as these substances may
potentially lead to chemical damage of the material.
x) Store in accordance with the manufacturer's instructions.