Napoleon Oakville Serie Manuel D'installation page 44

symptom
Motor is turning,
troubleshooting (electronic - GDIG3 / GDIX3)
frequent beeping
EN
occurs.
symptom
Lights or blower
won't function (if
Motor is turning,
equipped).
frequent beeping
occurs.
Flames are very
Lights or blower
aggressive.
won't function (if
equipped).
Appliance won't per-
form any functions.
Flames are very
aggressive.
Appliance won't per-
form any functions.
symptom
The following applies specifi cally to the SIT system only:
Pilot will not light.
Makes no noise with
symptom
no spark at pilot
burner. (Lights and
The following applies specifi cally to the SIT system only:
blower operate, if
equipped).
Pilot will not light.
f i r e - p a r t s . c o m
Makes no noise with
no spark at pilot
burner. (Lights and
blower operate, if
equipped).
note:
Starting from off, press the on button on the transmitter. Approximately 4 seconds on/off button is pressed, the ignition
board will start the spark. The fi rst try for ignition will last approximately 60 seconds. If there is no fl ame ignition (rectifi cation),
the board will stop sparking for approximately 35 seconds. After the wait time, the board will start the second try for ignition
by sparking for approximately 60 seconds. If there is still no positive ignition, the board will go into lock out.
note:
Starting from off, press the on button on the transmitter. Approximately 4 seconds on/off button is pressed, the ignition
board will start the spark. The fi rst try for ignition will last approximately 60 seconds. If there is no fl ame ignition (rectifi cation),
symptom
the board will stop sparking for approximately 35 seconds. After the wait time, the board will start the second try for ignition
by sparking for approximately 60 seconds. If there is still no positive ignition, the board will go into lock out.
The following applies specifi cally to the Maxitrol system only:
Pilot lights.
No gas fl ow.
symptom
The following applies specifi cally to the Maxitrol system only:
Pilot lights.
No spark after pilot
No gas fl ow.
ignition. Valve turns off
in one minute and does
not operate.
No pilot ignition
No spark after pilot
(5 second continuous ignition. Valve turns off
beep). in one minute and does
not operate.
No pilot ignition
44
(5 second continuous
W415-1802 / B / 02.07.19
beep).
problem
Wire connector pins are bent.
Receiver batteries low.
Valve wiring is damaged.
problem
Control module switch in
wrong position.
Receiver batteries low.
COM switch is unplugged.
Door is ajar.
Control module switch in
wrong position.
Venting action is too great.
COM switch is unplugged.
No power to the system.
Door is ajar.
Receiver switch in wrong
position (if equipped).
Venting action is too great.
Transmitter isn't operational.
No power to the system.
Receiver switch in wrong
problem
position (if equipped).
Transmitter isn't operational.
Ignition box has been locked
out.
problem
Ignition box has been locked
out.
problem
Manual override knob is in the
"MAN" position.
problem
Valve is not functioning properly.
Manual override knob is in the
Minimal voltage from thermocou-
"MAN" position.
ple or resistance in circuit ports
(Parts include: "ON/OFF" switch, Valve is not functioning properly.
receiver, thermocurrent connec-
tions or temperature switches).
Switch is in "OFF" position on
Minimal voltage from thermocou-
the valve. ple or resistance in circuit ports
(Parts include: "ON/OFF" switch,
Wiring is loose.
receiver, thermocurrent connec-
tions or temperature switches).
Receiver (if equipped).
Switch is in "OFF" position on
the valve.
Wiring is loose.
Wire connector pins are bent.
Receiver (if equipped).
test solution
- Straighten pins.
- Replace batteries.
- Replace valve.
test solution
- Verify ON/OFF switch is in the "I" position which denotes on.
- Replace batteries.
- Verify "COM" switch is plugged into the front of the control
module.
- Ensure door is secured properly.
- Verify ON/OFF switch is in the "I" position which denotes on.
- Check to ensure venting is properly sealed or restrict vent
exit with restrictor plate. (Not available in all appliances).
- Verify "COM" switch is plugged into the front of the control
module.
- Check breaker to verify it's in the "on" position.
- Ensure door is secured properly.
- Verify that the 3 position switch on the receiver is in the
remote position (middle).
- Check to ensure venting is properly sealed or restrict vent
exit with restrictor plate. (Not available in all appliances).
- Check battery power and battery orientation.
- Check breaker to verify it's in the "on" position.
- Verify that the 3 position switch on the receiver is in the
test solution
remote position (middle).
- Check battery power and battery orientation.
Choose one of the 3 methods below to reset the system.
1. To reset ignition box when locked out. Turn off power supply
test solution
and remove batteries (if used) from the back up battery pack.
To reset the DFC Board when the board goes into a lock
2.
out condition and the LED is blinking 3 times using the
transmitter on/off button:
Choose one of the 3 methods below to reset the system.
Step 1: Turn the system off by pressing the on/off
To reset ignition box when locked out. Turn off power supply
1.
button to turn the system off.
and remove batteries (if used) from the back up battery pack.
Step 2: After approximately 2 seconds press the on/
2. To reset the DFC Board when the board goes into a lock
off button on the transmitter again. The DFC Board will
out condition and the LED is blinking 3 times using the
reset and the ignition sequence will start again.
transmitter on/off button:
To reset the DFC Board when the board goes into a lock out
3.
Step 1: Turn the system off by pressing the on/off
condition and the LED is blinking 3 times by cycling fl ame:
button to turn the system off.
Step 1: In the manual fl ame control mode, use the down
Step 2: After approximately 2 seconds press the on/
arrow button to reduce the fl ame to off, indicated by the
off button on the transmitter again. The DFC Board will
word OFF displayed on the transmitter LCD screen.
reset and the ignition sequence will start again.
Step 2: Wait approximately 2 seconds and press the up
3. To reset the DFC Board when the board goes into a lock out
arrow button, the ignition sequence will start.
condition and the LED is blinking 3 times by cycling fl ame:
Step 1: In the manual fl ame control mode, use the down
arrow button to reduce the fl ame to off, indicated by the
word OFF displayed on the transmitter LCD screen.
Step 2: Wait approximately 2 seconds and press the up
arrow button, the ignition sequence will start.
test solution
- Turn the knob to the "ON" position.
test solution
- Valve is on pilot fl ow. Turn to the high setting, double click the large
fl ame button on the remote.
- Replace valve. Do not overtighten.
- Turn the knob to the "ON" position.
- Measure the voltage, it should read a least 5mV. The spade
connector is on the outer surface beside the magnet nut. Verify with
manufacturer the drop time, after thermocouple is heated measure
- Valve is on pilot fl ow. Turn to the high setting, double click the large
the drop time.
fl ame button on the remote.
- Replace valve. Do not overtighten.
- Switch to "ON" position.
- Measure the voltage, it should read a least 5mV. The spade
connector is on the outer surface beside the magnet nut. Verify with
manufacturer the drop time, after thermocouple is heated measure
- Ensure wiring is properly secured.
the drop time.
- Reset program: hold reset button on receiver and wait for 2 beeps.
Release after second beep. Press small fl ame button on remote
- Switch to "ON" position.
within 20 seconds, you will hear an additional beep (this signals a
successful reset).
- - Replace receiver. Ensure wiring is properly secured.
- Straighten pins.
- Reset program: hold reset button on receiver and wait for 2 beeps.