Cardin BL Série Mode D'emploi page 16

- make sure that the space between the bottom of the gate and the
pavement never exceeds 30 mm throughout the entire opening angle
of the gate.
• The surface of the gate must not feature openings which allow a person's
hand or foot to pass through.
• Check the exact positioning of the pivots, and their good working order
(the upper and lower hinges/pivots must be aligned on the same axis).
• Work out the run of the cables according to the command and control
devices fitted and make sure the system conforms to the local standard
and regulations in force (see installation example fig. 1 pag. 2).
• Check that the appliance is suitable for the size, weight and duty cycle
of the gate to which it is to be applied (see duty cycle on page 28)
FITTING THE UNITS 200/BL203- BL203L
The unit may be positioned either to the right or to the left of the pas-
sageway.
To install the unit correctly carry out the following procedure carefully.
• Move the gate/s to the closed position.
• Select the type of opening required (fig. 8, 9 pag. 5).
• Fasten the rear mooring bracket to the column (fig. 13 pag. 7), taking
into account the measurements "A" and "B", after having checked the
position of the gate hinge with respect to the column (measurement
"C" fig. 8, 9 page 5) according to the type of opening required.
• Fix the arm to the rear mooring bracket "5" using the retaining pin "1"
(fig. 2 pag. 3) and the front bracket "6" using the pin "7".
• Extend the arm manually until it reaches 5 mm from the end of the
travel distance.
ATTENTION! The centre distance between the front mooring
bracket "2" and the rear mooring bracket "1" must never exceed
1000 mm for the BL203 and 1345 mm for the BL203L (see figures
8-9 on page 5)
• Move the arm to its normal operating position, rest the head against
the gate and mark the position of the front bracket "6".
Note: Make sure the operator is perfectly level (using a spirit level) and
then fix the front bracket to the gate (fig. 14 pag. 7).
• The front bracket may be fixed in the following positions:
- on the gate frame or on a horizontal cross beam,
- if this is not possible, fix a reinforcing plate to the gate structure and
then fasten the front bracket onto the reinforcing plate.
• Insert the arm in the front bracket "6", insert the retaining pin "7" and
fasten down using the supplied C-clips (fig. 2 pag. 3).
• Install the protective carter by fastening the 4 screws on the geared
motor (pos. 2 fig. 2) and position the plastic protective cap (pos. 4 fig.
2).
• With the motor released move it manually to the fully open position and
check that all the components work correctly.
• If you are using 200/BL203L with a gate from 2 to 4 metres in width an
electric locking device must be fitted to ensure that the gate is blocked
when it is closed.
FITTING THE UNITS 200/BL352 - 200/BL452
The unit may be positioned either to the right or to the left of the passage-
way. To install the unit correctly carry out the following procedure carefully.
• Move the gate/s to the closed position.
• Select the type of opening required (fig. 8 pag. 5).
• Fasten the rear mooring bracket to the column (fig. 13 pag. 7), taking
into account the measurements "A" and "B", after having checked the
position of the gate hinge with respect to the column (measurement
"C" fig. 8 page 5) according to the type of opening required.
ATTENTION! The motor must be installed on the
gate with the humidity drain holes "A" facing
downwards (see drawing)
All rights reserved. Unauthorised copying or use of the information contained in this document is punishable by law
A
• Fix the arm to the rear mooring bracket "5" using the retaining pin "1"
(fig. 2 pag. 3) and the front bracket "6" using the pin "7".
• Extend the arm manually until it reaches 5mm from the end of the travel
distance.
ATTENTION! The centre distance between the front mooring
bracket "2" and the rear mooring bracket "1" must never exceed 1020
mm for the BL352 and BL452 (see figure 8 on page 5)
• Move the arm to its normal operating position, rest the head against
the gate and mark the position of the front bracket "6".
Note: Make sure the operator is perfectly level (using a spirit level) and
then fix the front bracket to the gate (fig. 14 pag. 7).
• The front bracket may be fixed in the following positions:
- on the gate frame or on a horizontal cross beam;
- if this is not possible, fix a reinforcing plate to the gate structure and
then fasten the front bracket onto the reinforcing plate.
• Insert the arm in the front bracket "6", insert the retaining pin "7" and
fasten down using the supplied C-clips (fig. 2 pag. 3).
• Install the protective carter by fastening the 4 screws on the geared
motor (pos. 2 fig. 2) and position the plastic protective cap (pos. 4 fig.
2).
• Extend the arm manually until it reaches 5mm from the end of the travel
distance.
• Mount the electric locking device (locks the gate in the closed position).
FITTING THE UNIT 200/BL203C - 200/BL203CE
The unit may be positioned either to the right or to the left of the pas-
sageway.
• Move the gate/s to the closed position.
• Select the type of opening required (fig. 10 pag. 5).
• Fasten the rear mooring bracket to the column (fig. 13 pag. 7), taking
into account the measurements "A" and "B", after having checked the
position of the gate hinge with respect to the column (measurement
"C" fig. 10 page 5) according to the type of opening required.
Note: if the gate brackets are to be pre-installed (front and rear)
without the presence of the piston, you must also consult the indica-
tions in figure 18.
• Position the protective carter "3" (with the scoring facing the gate),
fasten the 4 screws "2" positioned on the geared motor (tighten them
well down) and insert the plastic end cap "5" using the four supplied
screws (fig. 2 pag. 3).
• Rotate the never ending screw (part. 4 fig. 3) until it reaches 15 mm
from the end of the closing direction travel distance.
• Fix the arm to the rear mooring bracket "6" using the retaining pin "1"
(fig. 3 pag. 3).
• Move the arm to its normal operating position, rest the head against
the gate and mark the position of the front bracket "6".
Note: Make sure the operator is perfectly level (using a spirit level).
- position the front holding bracket (fig. 14 pag. 7)
• The front bracket may be fixed in the following positions:
- on the gate frame or on a horizontal cross beam,
- if this is not possible, fix a reinforcing plate to the gate structure and
then fasten the front bracket onto the reinforcing plate.
• Insert the retaining pin of the never ending screw "4" into the front
bracket "9" and fasten down using the supplied screw and washer
"8" (fig. 3 pag. 3).
• With the motor released move it manually to the fully open position
and check that all the components work correctly.
• If you are using 200/BL203C - 200/BL203CE with a gate from 1,8 to
3 m in width an electric locking device must be fitted to ensure that
the gate is blocked when it is closed.
16