Publicité
OBJ_BUCH-0000000025-001.book Page 17 Friday, February 25, 2011 9:30 AM
Use only intact original FEIN batteries that are intended
for your power tool. When working with and charging
incorrect, damaged, repaired or reconditioned batteries,
imitations or other brands, there is danger of fire and/or
explosion.
Follow the safety warnings in the operating instructions
of the battery charger.
Handling hazardous dusts
For work procedures with this power tool where mate-
rial is removed, dusts develop that can be hazardous to
one's health.
Contact with or inhaling some dust types, e. g. asbestos
and asbestos-containing materials, lead-containing coat-
ings, metal, some wood types, minerals, silicate particles
from materials containing stone, paint solvents, wood
preservatives, antifouling paints for vessels, can trigger
allergic reactions to the operator or bystanders and/or
lead to respiratory infections, cancer, birth defects or
other reproductive harm. The risk from inhaling dusts
depends on the exposition. Use dust extraction matched
appropriately for the developing dust, as well as personal
protective equipment and provide for good ventilation of
the workplace. Leave the processing of asbestos-contain-
ing materials to specialists.
Wood and light-metal dust, hot mixtures of sanding dust
and chemical materials can self-ignite under unfavourable
conditions or cause an explosion. Avoid sparking in the
direction of the dust collector as well as overheating of
the power tool and the materials being sanded, empty the
dust collector/container in time, observe the material
manufacturer's working instructions, as well as the rele-
vant regulations in your country for the materials being
worked.
Hand/arm vibrations
The vibration emission level given in this information
sheet has been measured in accordance with a standard-
ised test given in EN 60745 and may be used to compare
one tool with another. It may be used for a preliminary
assessment of exposure.
The declared vibration emission level represents the
main applications of the tool. However if the tool is used
for different applications, with different accessories or
poorly maintained, the vibration emission may differ.
This may significantly increase the exposure level over
the total working period.
An estimation of the level of exposure to vibration
should also take into account the times when the tool is
switched off or when it is running but not actually doing
the job. This may significantly reduce the exposure level
over the total working period.
Identify additional safety measures to protect the opera-
tor from the effects of vibration such as: maintain the tool
and the accessories, keep the hands warm, organisation
of work patterns.
Emission values for vibration
Vibration
Classification of FEIN application
tools according to vibration class
VC0
VC1
VC2
VC3
VC4
VC5
Ka
* These values are based on a work cycle consisting of no-load
and full-load operation of the same duration.
For information on the vibration class assigned to the application
tool, please see the enclosed data sheet 3 41 30 335 06 0.
Operating instructions.
Do not use accessories not specifically intended and rec-
ommended for this power tool by FEIN. The use of non-
original FEIN accessories can lead to overheating of the
power tool and destroy it.
Guide the power tool toward the work piece only
when switched on.
The application tool can be offset in 45° steps and fas-
tened in the most favourable working position.
Changing the tool (see page 5).
Firmly press in the fastening element to the stop.
Then lock the clamping lever.
Protect your hand and fingers against bruising them
when locking the clamping lever. The clamping
lever snaps back vigorously by means of spring
force.
Handling the battery.
Operate and charge the battery only within the battery
operating-temperature range of 0 °C – 45 °C (32 °F –
113 °F). At the beginning of the charging procedure, the
battery temperature must be within the battery operat-
ing-temperature range.
LED indicator
Meaning
1 – 4 green
Percentage of
LED
charge condi-
tion
Continuous
Battery is
red light
almost empty
Red flashing
Battery is not
light
ready for oper-
ation
The real percentage of the battery charge condition is
only indicated when the power tool motor is stopped.
The electronics automatically switch off the motor prior
to the battery being deep discharged.
en
17
a
Weighted
acceleration*
2
< 2.5 m/s
2
< 5 m/s
2
< 7 m/s
2
< 10 m/s
2
< 15 m/s
2
> 15 m/s
2
3 m/s
Activity
Operation
Charge battery
Bring the battery into
the battery operating-
temperature range,
then charge
Publicité
