Parameter Adjustment Procedure: Sbs Input Configuration - Flash Output Configuration - Discharging Of Motor; Verifying The Values Set For Each Parameter (Using The Transmitter); Parameter Verification Procedure: Discharging Of Motor 1 Upon Closing - Discharging Of Motor 1 Upon Opening - Discharging Of Motor 2 Upon Closing - Discharging Of Motor 2 Upon Opening - Nice ARIA200 Manuel D'installation Et D'utilisation

9.1.1.2 - Parameter adjustment procedure: SbS input configuration - Flash output configura-
tion - Discharging of Motor 1 and 2 upon closing - Discharging of Motor 1 and 2 upon opening
Before proceeding, check the parameter to be modified in Table 3 and the action to be performed:
01. On the transmitter (Fig. 23) simultaneously press and hold keys T1 and T3 for 5 seconds then
release them.
02. Within 3 seconds from releasing them, perform the action specified in Table 3 to modify the desired
parameter.
Parameters Value
SbS input con- Step-by-step *
figuration
Pedestrian opening
F l a s h o u t p u t Flashing light *
configuration
Courtesy light
Gate open indicator
Discharging of No discharge *
Motors 1 and 2
0.1 sec (minimum)
upon
0.2 sec
closing
0.3 sec
0.4 sec (average)
0.5 sec
0.6 sec
0.7 sec (maximum)
Discharging of No discharge *
Motors 1 and 2
0.1 sec (minimum)
upon
0.2 sec
when gate
0.3 sec
opens
0.4 sec (average)
0.5 sec
0.6 sec
0.7 sec (maximum)
* Factory value
9.1.2 - Verifying the values set for each parameter (using the transmitter memorised in Mode 1)
The check can be effected by means of any transmitter memorised in Mode 1 (as those supplied, see Paragraph 9.3.1). If there is no transmitter memo-
rised in Mode 1, it is possible to memorise one solely for programming purposes then cancelling it (see Paragraph 9.4).
9.1.2.1 - Parameter verification procedure: Pause time - Pedestrian opening - Motor force - Step-by-Step (SbS) function
Before proceeding, check the parameter to be modified in Table 4 and the action to be performed:
01. On the transmitter (Fig. 24) simultaneously press and hold buttons T1 and T2 for 5 seconds then release them.
02. Within 3 seconds from releasing them, perform the action specified in Table 4 to verify the desired parameter.
03. Release the key when the flashing light starts flashing: count the flashes.
Check in Table 2 the value corresponding to the number of flashes.
Parameters Actions to be performed
Pause time Press and hold key T1
Pedestrian opening Press and hold key T2
Motor force Press and hold key T3
Step-by-Step function
Press and hold key T4
9.1.2.2 - Parameter verification procedure: Discharging of Motor 1 upon closing - Discharging of Motor 1 upon opening - Discharging of
Motor 2 upon closing - Discharging of Motor 2 upon opening
Before proceeding, check the parameter to be modified in Table 5 and the action to be performed:
01. On the transmitter (Fig. 25) simultaneously press and hold keys T1 and T3 for 5 seconds then release them.
02. Within 3 seconds from releasing them, perform the action specified in Table 5 to verify the desired parameter.
03. Release the key when the flashing light starts flashing: count the flashes.
Check in Table 3 the value corresponding to the number of flashes.
Parameters
Discharging of Motor 1 upon closing
Discharging of Motor 1 upon opening
Discharging of Motor 2 upon closing
Discharging of Motor 2 upon opening
12 – English
TABLE 4
TABLE 5
Actions to be performed
Press and hold key T1
Press and hold key T2
Press and hold key T3
Press and hold key T4
TABLE 3
No. of flashes emitted by Transmitter key to be
the flashing light used
1 T1
2 T1
T2
1
2 T2
3 T2
1 T3
2 T3
3 T3
T3
4
5 T3
6 T3
7 T3
8 T3
1 T4
T4
2
3 T4
4 T4
5 T4
6 T4
7 T4
T4
8
23
T1
Actions to be per-
formed
Press T1 once
Press T1 twice
Press T2 once
Press T2 twice
Press T2 three times
Press T3 once
Press T3 twice
Press T3 three times
Press T3 four times
Press T3 five times
Press T3 six times
Press T3 seven times
Press T3 eight times
Press T4 once
Press T4 twice
Press T4 three times
Press T4 four times
Press T4 five times
Press T4 six times
Press T4 seven times
Press T4 eight times
24
1
25
T1
T3
2
T3