Technical Data - Scheppach MIX160 Mode D'emploi

•
Cracks in insulation due to ageing. Such dam-
aged electrical connecting cables should not
be used, they can be fatal due to damaged in-
sulation!
Check electrical connecting cables regularly for
damage. Ensure that when checking the con-
necting cable, it does not hang from the power
mains. Electrical connecting cables must corre-
spond to the common VDE and DIN provisions.
Use only connecting cables that have the desig-
nation H 07 RN.
An imprint of the type designation on the con-
necting cable is mandatory.
1. Supporting stand, front
2. Motor casing
3. Frame
4. Swivel wheel
5. Drum upper section
6. Bearing bracket
Motor
Capacity
Protection class
Dimensions
Weight
D GB
Sound pressure level L / uncertainty K
pA
Sound power level L / uncertainty K
WA
Warning: Noise can seriously damage your
health. If the engine noise exceeds 85 dB (A),
please wear appropriate hearing protection. If
the electrical connection is faulty, the current
may drop when the machine starts. This may af-
fect other machines (e.g. flashing lights). If the
electric output corresponds to Zmax <0.27, such
interference should not occur. (If it does, notify
your dealer).
• The vibration emission value given below has
been measured by a standardized test, and
Take the concrete mixer out of the carton with the
help of two persons.
Caution!
The concrete mixer should be used only after it
is installed fully.
1. Installing wheels Fig.3
Install splint on both sides, washer, wheel (12),
washer, splint on the supporting stand rear with
wheel axle (11).
Bend the splints slightly after installation
AC Motor
AC motor 230 V/ 50 Hz, mains voltage 230 Volt
/ 50 Hz.
Use of a residual current protection device ("FI")
is recommended for a 230V connection. If you
use an extension cable, insert it directly into the
FI.
If operating it in Switzerland, insert the concrete
mixer only in sockets that are protected by a re-
sidual current-operated circuit breaker.
Mains connection and extension cable can have
3 wires as well as 2.
3-wire: P + N + SL. - (1/N/PE); 2-wire: P + N –
(1/N)
Extension cables must have a minimum cross-
section of 1.5 mm².
Equipment packing list Fig.1
7. Drum lower section
8. Instructions
9. Mixer
10. Bag provided (Fig. 2 Content)
11. Supporting stand, rear with wheel axle
12. 2 wheels

Technical data

MIX160
230V / 50 Hz 0,65 kW
160 l
IP45D
1280mm x 840mm x 1300mm
56 kg
70 dB(A) / 2.8dB(A)
93 dB(A) / 2.8dB(A)
Information on noise
can be used for comparing one power tool to
another;
•
The vibration emission value given below may
also be used for a first assessment of expo-
sure.
Warning:
•
The vibration emission value may vary during
actual use of the power tool from the specified
value, depending on the manner in which the
power tool is used;
Unpacking
Check to ensure that the delivery is complete.
Montage
2. Installing the front supporting stand with
frame Fig.4
Insert the supporting leg into the frame and se-
cure it with two M8x70 hexagon bolts. Insert the
spring into the designated fixture. From below,
insert the actuating rod through the spring and
connect it to the extension rod.
16
Connecting cable, plug and coupling jack must
be protected against water spray.
The mains connection is protected with a maxi-
mum 16A fuse.
Connections and repairs of the electrical
equipment should be performed by electri-
cians only.
Please quote the following information in
your queries:
•
Current type of the motor.
•
Data on the machine ratings plate.
When returning the motor, always send the com-
plete drive unit with switch.
13. Locking washer
14. Operating rod
15. Extension
16. Locking plate
• Try to keep exposure to vibration to a mini-
mum. Examples of ways to reduce vibration
levels are wearing gloves when using the
tool and limiting working hours. In doing so,
all parts of the operating cycle must be taken
into account (for example, times in which the
power tool is turned off, or when it is turned
on without load).
Inform the dealer if there are faults.
3. Installing the frame with the wheel sup-
ports Fig. 5
Install frame and wheel supports fully with 2
M8x70 hexagon bolts, 2 8mm washers, 2 lock-
washers and 2 M8 nuts. Tighten the screws.