Chicco Auto-Fix FAST Mode D'emploi page 18

(Diag. 24) WARNING! Never insert just
one end of the harness into the buckle
and do not insert them one at a time.
5. Tighten the safety harness by pulling the
adjuster strap (Diag. 25)
3.2 ADJUSTING THE POSITION OF
THE HARNESS STRAPS
WARNING! The harness straps must always
be adjusted to adapt to the child's growth
phase. Before installing the child car seat
inside the vehicle, adjust the harness straps
to the right height.
To adjust them correctly, the harness straps
must come out from the backrest at the
height of the child's shoulders (Diag. 26)
The child car seat straps can be adjusted to
3 height positions.
To adjust the harness straps, proceed as
follows:
1. Remove the shoulder pads by unthreading
them through the slots in the fabric cover.
2. Press the red button to open the har-
ness buckle.
3. Slide the harness straps out from behind
the backrest and thread them though the
slot which is most suitable for the child's
height (Diag. 27A and 27B).
WARNING! Make sure that the harness
straps are always threaded between the
slot element ( R) and the shell.
WARNING! The booster cushion guarantees
correct containment and the ideal position
for the neck and back of babies from when
they are born until they weigh about 6 Kg.
3.3 FIXED OR ROCKING POSITION
OF THE CHILD SEAT (ROCKER
CHAIR MODE)
When the child car seat is not used inside
the vehicle, it can be used as a rocking or
static chair.
To allow it to rock, close the stabiliser block
(Diag. 14) and move the carry handle to
position B (Diag. 5).
To use it in fi xed mode, fold out the stabiliser
block and move the handle bar to position
D (Diag. 5).
Only place the child seat on stable hori-
zontal surfaces.
WARNING! Before carrying the child car
seat, always bring the carry handle into a
vertical position (B).
WARNING! Never leave your child
unattended.
WARNING! Always use the re-
straint harness.
WARNING! Using the child car seat
on raised surfaces such as tables,
chairs etc can be very dangerous.
WARNING! This child car seat is
not designed for long periods of
sleep.
WARNING! Do not use the seat
when the child is able to sit up on
his own.
This child car seat is not a replacement for a
bed or cot. If the child needs to sleep, they
should be moved to a bed or a cot.
Do not use the child seat if some of its parts
are broken or missing.
3.4 USE WITH THE STROLLER
WARNING! The Auto-Fix car seat can be
fi tted to Chicco strollers equipped with
the specifi c fi xing system as standard or
a fi tting adaptor system can be purchased
separately.
WARNING! Please read the Stroller instruc-
tion manual when using the child car seat
on the stroller. The CHICCO strollers, which
use the CLIK CLAK system, have armrests
with special devices that allow you to fasten
the child seat to the stroller frame without
any need for additional fi xtures.
Before fi xing the car seat, remove the arm
covers completely.
To install the child seat on the stroller, pro-
ceed as follows:
1. Bring the carry handle into a vertical posi-
tion (Diag. 28).
2. Attach the two Clik Clak fi xing hooks of
the Car seat (N) to the armrests of the
stroller or to the fi xing system purchased
separately, making sure that they are cor-
rectly fi xed on both sides. A click will be
heard confi rming fi xing (fi g. 29).
WARNING!
Before use, ensure that all the child seat-fas-
tening devices are correctly fi tted in place.
18