Stanley 46126400 Manuel De L'utilisateur page 3

EX: Angle between arms = 135°
Supplemental angle = 45°
STEP 1: Start compound mitre mode. Press the MITRE button
for >2 seconds. The SPR indicator
that was last stored into memory will be shown for ~2 seconds.
STEP 2: The SPR indicator will stop flashing and the display
7
will again show the active angle. If the stored SPR angle needs
to be changed, adjust the arms
13
matches the known spring angle (Typ. 38° or 45°). Then press the
MITRE button for >2 sec. The displayed angle and SPR will
15
flash once and the spring (SPR) angle is now stored in memory.
If the stored spring angle does not need to be changed, press
MITRE button for ~1 second to move to the next step.
15
STEP 3: If you do not already have the CNR indicator
in the display, press the MITRE button
indicator will flash and the CNR angle that was last stored
6
into memory will be shown for ~2 seconds. The CNR indicator
will stop flashing and the display will again show the active
6
angle. If the stored CNR angle needs to be changed, adjust the
arms & as shown in . To store the corner angle into
13 16 G
memory, press the MITRE button
angle and the CNR indicator
6
(CNR) angle is now stored in memory.
If the stored corner angle does not need to be changed, press
MITRE button for ~1 second to move to the next step.
15
STEP 4: If you do not already have the MTR indicator
in the display, press the MITRE button
calculated mitre angle for setting the saw. See
STEP 5: Press the MITRE button
display to the bevel angle. The BVL indicator
This is the bevel angle for setting the saw. See
Press the MITRE button for ~1 sec. to cycle back through the
15
stored spring angle, the stored corner angle and the calculated
mitre and bevel angles.
Press the ON/OFF button at any time for ~1 sec. to exit
12
compound angle mode.
6
WALL
SIDE
15
will flash and the SPR angle
7
& until the displayed angle
16
shown
6
for ~1 sec. The CNR
15
for >2 sec. The displayed
15
will flash once and the corner
shown
5
for ~1 sec. This is the
15
, Angle M.
D
for ~1 sec to change the
15
will be displayed.
4
, Angle B.
D
42-087
SPECIFICATIONS
Power:
3VDC (2) AAA Batteries
(included)
(Alkaline recommended)
Measuring Range:
0-225°
Digital Angle accuracy:
±0.1°
Vial(s) Accuracy:
0.057°(1 mm/m)
Operating Temperature:
-10° to 50°C (14° to 122°F)
Storage Temperature:
-20° to 70°C (-4° to 158°F)
Battery life: ~100 Hrs
Shock Resistance:
Up to 1m (3 feet) drop on concrete
Water Resistance:
Water resistant, but not waterproof
WARRANTY
One Year Warranty
Stanley warrants its electronic measuring tools against
deficiencies in materials and / or workmanship for one year from
date of purchase.
Deficient products will be repaired or replaced, at Stanley's
option, if sent together with proof of purchase to:
Stanley UK Sales Limited
Gowerton Road
Brackmills, Northampton NN4 7BW
This Warranty does not cover deficiencies caused by accidental
damage, wear and tear, use other than in accordance with the
manufacturer's instructions or repair or alteration of this product
not authorised by Stanley.
Repair or replacement under this Warranty does not affect the
expiry date of the Warranty.
To the extent permitted by law, Stanley shall not be liable under
this Warranty for indirect or consequential loss resulting from
deficiencies in this product.
This Warranty may not be varied without the authorisation of
Stanley.
This Warranty does not affect the statutory rights of consumer
purchasers of this product.
This Warranty shall be governed by and construed in accordance
with the laws of the country sold where in and Stanley and the
purchaser each irrevocably agrees to submit to the exclusive
jurisdiction of the courts of that country over any claim or matter
arising under or in connection with this Warranty.
42-087
7
English