Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
Digital Bevel
OPERATING INSTRUCTIONS
Installing Batteries: See
C
1. Lift arm to expose battery Compartment which is located on
the back of the product.
2. Remove cover as shown.
3. Insert (2) AAA batteries as shown.
4. Replace cover & snap in place.
Display: See
B
1. Battery Life icon
2. SUP indicator
3. HOLD indicator
4. BVL indicator
5. MTR indicator
6. CNR indicator
7. SPR indicator
8. Angle display
Features: See
A
9. Level Vial
10. Plumb Vial
11. HOLD/SUP Button
12. ON/OFF Button
13. Adjustable Arm
14. Tension Knob
15. MITRE Button
16. Level Arm
Power:
Press the ON/OFF button
for ~1 sec. to turn on the display
12
and backlight.
• The angle
which represents the angle between the arms
8
&
will be displayed in degrees (°).
13
16
• The display will automatically power off after ~5 minutes of
non-use.
• The backlight will automatically power off after ~1 minute
of non-use. Any button press or angle change will cause the
backlight to power on if the display is powered on.
• The battery life icon
will appear when there is ~ 2 hours of
13
battery life remaining.
• Press the ON/OFF button
12
display.
Invert Display:
With the display powered on, press the ON/OFF button
sec. to invert the display. Press again for ~1 sec. to return display
to normal position.
Re-calibrate:
If the unit is dropped or you suspect inaccuracy of the product,
you can re-calibrate the zero point.
With the power on and the arms
the ON/OFF
and HOLD/SUP
12
11
sec. to reset to angle to 0°.
Hold:
Press the HOLD/SUP button
for ~1 sec. to lock the current
6
angle shown on the display. The HOLD indicator
and flash on the display. Press
6
displayed angle.
Supplemental Angle:
Press the HOLD/SUP button
for >2 sec. to change the display
6
to the supplemental angle. The supplemental angle is 180° minus
4
for >2 sec. to power off the
for ~1
12
&
closed together, press
13
16
buttons simultaneously for >2
will appear
3
again for ~1 sec. to unlock the
42-087
the current angle between the arms
will appear and flash on the display. Press
2
sec. to return to normal angle.
Easy Mitre Angle:
With the arms
&
set to the desired angle, press the MITRE
13
16
button
for ~1 sec. The mitre angle (90°- ½X) will be shown.
15
The display will be locked on that angle and the MITRE indicator
will appear and flash on the display. To set the mitre saw, see
5
, setting M.
D
X
MTR
Compound Angle Mode:
For compound angles such as cuts for crown molding, you will
need to enter compound mitre mode and store two angles into
memory; the Spring (SPR) and Corner (CNR) angles. (See
&
) The unit will then calculate the Mitre and Bevel angles
G
needed to set a compound mitre saw. See
& B (bevel).
Note: I f you do not know the spring angle of the item you are
working with, it is easier to get that angle before starting.
(The spring (SPR) angle is usually 38° or 45° for crown
molding.) See
.
F
WALL
This is done by placing the molding as shown in
are set to matching the angle of the item, press the HOLD/SUP
button
for >2 sec to get the supplemental angle. That will be
6
the spring (SPR) angle.
42-087
&
. The SUP indicator
13
16
again for >2
6
F
, settings M (mitre)
D
CEILING
CORNER ANGLE
(CNR)
Once the arms
H
5
English
Publicité
Table des Matières
