Metabo KGS 303 Instructions D'utilisation page 8

Table des Matières

Publicité

Les langues disponibles

Les langues disponibles

ENGLISH
A
WARNING
Before plugging the machine in,
check the voltage and cycle rating
(120 V, 60 Hz) on the nameplate of
the machine and make sure you
have a proper power source with
the same rating. If not, consult a
qualified electrician for assistance.
Be careful not to kink, squeeze or
pull the power cord and/or any
extension cord, and make sure that
you protect the cord(s) from dam-
age caused by rolling over, heat,
aggressive substances like acid, or
other potential damage arising at
the work site.
If the power cord or an extension
cord is damaged, never try to repair
it, but have a qualified electrician or
other authorized repair personnel
replace the damaged cord.
A
CAUTION
To avoid electrical shock, ensure
there is no contact with grounded
objects such as radiators, pipes,
ovens, refrigerators, etc. when
operating this machine.
Ensure nobody can trip over or
inadvertently pull on the power
cord.
Never pull on the power cord to
unplug the machine as this can
damage the cord and lead to a
hazard.
Risk of injury by moving parts
A
DANGER
Do not operate the machine with-
out installed guards.
Make sure the power cord is
unplugged before servicing, trou-
bleshooting or changing parts.
Remove all tools and loose parts
from the machine before plugging
in and operating the machine after
service or troubleshooting.
After completing a cut, do not let go
of the handle of the machine or
your work piece until all moving
parts of the machine have come to
a full stop.
A
WARNING
When the machine is not in use,
switch it to OFF and unplug it.
8
A
WARNING
Make sure your work pieces are
secured in place during cutting so
that they cannot move.
Work stock only in the direction
intended for the machine.
Do not exert exessive force on the
machine with the work piece.
Never have the machine running
unattended.
Turn
power
Don't leave the machine until it
comes to a full stop.
Entanglement with the machine
A
DANGER
Be careful that no part of your body or
your clothing can be caught by and
pulled into the machine.
Do not wear any loose clothing.
Do not wear any gloves.
Long hair has to be covered (for
example by making a pony tail and
then tucking the hair in under a cap
or hat).
Dangling jewelry, rings, bracelets,
necklaces and other personal items
which might get caught in the
machine have to be removed
before starting to work with this
machine.
Insufficient personal protection gear
A
WARNING
Use eye protection. Always wear
ANSI approved impact safety gog-
gles. If you are producing metal fil-
ings or wood chips, wear a full face
shield.
Use ear protection. Always wear
ANSI approved ear protection such
as ear plugs or ear muffs.
Use respiratory protection when
working around metal, wood, espe-
cially treated wood, chemical dusts
or mists. Always wear an ANSI
approved dust mask or respirator
or other respiratory protection in
accordance with current OSHA,
MSHA and NIOSH regulations.
Wear head protection if required by
your type of work or by regulations
applying to the job site.
Wear protective, electrically non-
conductive clothes and non-skid
foot wear.
A
CAUTION
Wear suitable work clothes.
When working outdoors wearing
of
non-slip
mended.
Ensure a fire extinguisher is within
reach.
Dust
OFF.
A
DANGER
DO NOT CUT ANY HAZARDOUS
MATERIALS
THAT
CONTAIN
SUBSTANCES OR HAVE BEEN
TREATED
SUBSTANCES.
A
WARNING
Some types of wood dust (e.g.
maple, oak, cedar) may cause
allergic reactions and other health
problems such as skin rashes, etc.
If possible, work with a suitable
dust collector connected to the
saw. The dust collector must com-
ply with the data stated in chapter
15, entitled "Technical Specifica-
tions".
Dust generated by sawing, sand-
ing, drilling and similar work may
contain substances that are known
or suspected to cause cancer,
damage to reproductive organs
and/or the ability to procreate, and/
or may cause damage to fetuses
and unborn children. Lead, lead
paint, arsenic or chromium treated
wood (often referred to as "green
wood" or pressure-treated lumber)
and quartz dust or silica from con-
crete are just some, but in no case
an exclusive list of such sub-
stances. The actual health risk
depends on the length of exposure
to these substances, the circum-
stances as well as the degree of
respiratory and other protection
used.
shoes
is
recom-
OR
MATERIALS
HAZARDOUS
WITH
HAZARDOUS

Publicité

Table des Matières
loading

Table des Matières