Technical Specifications - Hudora 14126 Instructions De Montage Et Mode D'emploi

INSTRUCTIONS ON ASSEMBLY AND USE
EN
CONGRATULATIONS ON PURCHASING
THIS PRODUCT!
Please read these instructions carefully. The instructions are an
integral component of the product. Therefore, please store them
and the packaging carefully in case questions arise in the future.
Please always include these instructions when handing on the
product to a third party. This product must be assembled by an
adult. This product is designed for private/domestic use only. This
product is not designed for commercial/industrial use. The use
of the product requires specific skills and knowledge to be able
to avoid injuries due to crashes and collisions. Always adjust ac-
cording to the age of the user and use for the purpose it has been
designed for.

TECHNICAL SPECIFICATIONS

Item: HUDORA BigWheel
(Wheel size: 215/180 mm)
Item number: 14126, 14127
Dimensions: approx. 88 cm in length,
deck approx. 37 x 12 cm
Product weight: approx. 4.1 kg
Class: A, 100 kg maximum user weight
Purpose: Leisure scooter for use on public areas, no toy.
If you have assembly problems or would like further information
on the product, we have all you need and more at http://www.
hudora.de/.
CONTENTS
1 x scooter (cf. parts list on page 2) | 1 x these instructions
Other parts which may be included with the delivery in some cir-
cumstances are not required.
SAFETY INSTRUCTIONS
• This scooter needs to be partially assembled before first using.
To avoid pinching or entrapment please follow exactly the in-
structions on assembly below and make sure that all parts are
assembled correctly and tightly.
• Keep young children away while assembling. There is a risk of
choking hazard from small parts!
• Wear suitable protective clothing for your own safety. Wear
personal protective equipment. This includes at least: hand/
wrist guards, knee pads, head protection and elbow pads. Nev-
er use the scooter without shoes!
• The scooter is only intended for use by one person.
• Only use the scooter on surfaces that are suitable for it, i.e. those
which are flat, clean, dry, and use the scooter where possible
away from other road users. Avoid sloping ground. The brakes
may become hot if the scooter has been used for a while! Your
footwear could be damaged! The brakes shouldn't be touched
until they have cooled down.
• Always be considerate of others.
• Before you begin – Ensure that all fasteners and locking parts
are intact and tight, e.g. the folding mechanism and the height
setting of the handlebar. The functions of self-securing screw
threads can be impaired after repeated loosening and tighten-
ing of the connecting elements. Check especially for the correct
alignment and fastening of the steering set-up.
215
®
• Make sure that the stand is folded safely while driving.
• Do not use the scooter at twilight, at night or in poor visibility.
Do not use it on roads or thorough-fares or on slopes or hills.
Avoid being in the proximity of stairs and open water.
• The scooter is not suitable for jumps.
• Prior to using the scooter, please inform yourself about restrict-
ing applicable traffic regulations for the intended area of appli-
cation.
• The use of the product requires specific skills and knowledge to
be able to avoid injuries due to crashes and collisions.
• Children should only use the product when they are under adult
supervision.
• Ensure when riding that the logo on the handlebar points to the
front or else that the push buttons is as such oriented back-
wards.
INSTRUCTIONS ON ASSEMBLY
1. Connect and fasten the handlebar (1) and deck (2) with the sup-
plied screw set (6, 8, 10) as shown in Fig. 1.
2. Screw on the handlebar (1/3) as shown in Fig. 2. Then put the
cover cap (14) on the opening in the housing. Make sure that the
cap fits perfectly. It should not be easy to detach.
3. Mount the front wheel (4) as shown in Fig. 3. Make sure that the
long sleeve screw (7) is on the right-hand side and the short
side of the bolt (9) is mounted on the left-hand side in the di-
rection of travel.
4. Mount the stand (5) as shown in Fig. 4. The scooter is now com-
pletely assembled (Fig. 5).
PLEASE PROCEED AS FOLLOWS TO GET THE SCOOTER READY
FOR USE
• Pull the lever on the right or left above the footboard to release
the folding mechanism.
• Fold the handlebars of the scooter forwards until it audibly
clicks into place (Fig. 6).
• Loosen the quick release lock on the handlebar rod by pushing
the lever of the quick release lock until the lever is parallel to the
handlebar grip. (Fig. 7)
• The handlebars can be locked into place at 4 different heights.
Pull the handlebar rod out of the handlebar stem until it is at the
required height and the relevant button has snapped into place.
(Fig. 8) The maximum height cannot be exceeded due to the in-
tegrated lock. If the handlebar does not sit firmly at the required
height, open the quick release lock again and turn the opposite
screw deeper into the thread, so that the fastening bracket fits
more tightly to the handlebar rod. Repeat this process until the
handlebar rod can be aligned securely.
• Now close the quick release lock by pushing the lever down to
the handlebar stem.
• Always check all parts before use to ensure they are fitting
tightly, particularly the folding mechanism, the handlebar lock-
ing and the wheels.
TO GET THE SCOOTER READY FOR TRANSPORT AGAIN,
PLEASE CARRY OUT THE FOLLOWING ACTIONS
• Loosen the quick release lock by pushing the lever of the quick
release lock away from the handlebar stem. (Fig. 7)
• Please press the locking button so that the handlebar rod can
be moved.
8/24