About The Documentation; About The Box - Rotex RHBH04CA3V Manuel D'installation

Table of contents

1 About the documentation

1.1 About this document ........................................................................1

2 About the box

2.1 Indoor unit ........................................................................................1
2.1.1 To remove the accessories from the indoor unit...................1
3 Installation
3.1 Opening the units .............................................................................2
3.1.1 To open the indoor unit .........................................................2
3.1.2 To open the switch box cover of the indoor unit ...................2
3.2 Mounting the indoor unit...................................................................3
3.2.1 To install the indoor unit........................................................3
3.2.2 To install the drain pan kit .....................................................4
3.3 Connecting the refrigerant piping .....................................................4
3.3.1 To connect the refrigerant piping to the indoor unit ..............4
3.4 Connecting the water piping.............................................................4
3.4.1 To connect the water piping..................................................4
3.4.2 To fill the water circuit ...........................................................5
3.4.3 To fill the domestic hot water tank ........................................5
3.4.4 To insulate the water piping ..................................................5
3.5 Connecting the electrical wiring .......................................................5
3.5.1 About electrical compliance..................................................5
3.5.2 To connect the electrical wiring on the indoor unit................5
3.5.3 To connect the main power supply .......................................6
3.5.4 To connect the backup heater power supply ........................7
3.5.5 To connect the user interface ...............................................8
3.5.6 To connect the shut-off valve................................................9
3.5.7 To connect the electrical meters ...........................................9
3.5.8 To connect the domestic hot water pump .............................9
3.5.9 To connect the alarm output .................................................9
3.5.10 To connect the space cooling/heating ON/OFF output.......10
3.5.11 To connect the changeover to external heat source...........10
3.5.12 To connect the power consumption digital inputs ...............10
3.6 Finishing the indoor unit installation ...............................................10
3.6.1 To fix the user interface cover to the indoor unit.................10
3.6.2 To close the indoor unit.......................................................10
4 Configuration
4.1 Overview: Configuration................................................................. 11
4.2 Basic configuration......................................................................... 11
4.2.1 Quick wizard: Language / time and date ............................ 11
4.2.2 Quick wizard: Standard....................................................... 11
4.2.3 Quick wizard: Options.........................................................12
4.2.4 Quick wizard: Capacities (energy metering).......................13
4.2.5 Space heating/cooling control.............................................13
4.2.6 Domestic hot water control .................................................14
4.2.7 Contact/helpdesk number...................................................14
4.3 Menu structure: Overview installer settings ...................................15
5 Commissioning
5.1 Checklist before test run ................................................................16
5.2 To perform an air purge..................................................................16
5.3 To perform a test run ......................................................................16
5.4 To perform an actuator test run ......................................................16
5.4.1 Possible actuator test runs .................................................16
5.5 To perform an underfloor heating screed dryout ............................16
6 Hand-over to the user
7 Technical data
7.1 Wiring diagram ...............................................................................18
7.1.1 Wiring diagram - components: Indoor unit.........................18
RHBH/X04+08+16CA
Rotex HPSU low temperature Bi-Bloc
4P330419-1A - 2012.11
1 About the documentation
1
1.1 About this document
1
Target audience
Authorized installers
Documentation set
2
This document is part of a documentation set. The complete set
consists of:
Document
General Safety instructions that
safety you must read before
precautions installing
Indoor unit Installation instructions
installation
manual
Outdoor unit Installation instructions
installation
manual
Installer Preparation of the
reference installation, technical
guide specifications, good
practices, reference
data,...
Addendum Additional info about how
book for to install optional
optional equipment
equipment
Latest revisions of the supplied documentation may be available on
the regional Rotex website or via your dealer.
2 About the box
11
2.1 Indoor unit
2.1.1 To remove the accessories from the indoor
unit
The installation manual indoor unit, operation manual, and CD/DVD
are located in the upper part of the box. Follow the procedure below
to remove the other accessories.
1 Remove the tape.
16
17
18
1 About the documentation
Contains... Format
Paper (in the box of the
indoor unit)
Paper (in the box of the
outdoor unit)
CD/DVD (in the box of the
indoor unit)
Paper (in the box of the
indoor unit)
CD/DVD (in the box of the
indoor unit)
Installation manual
1