Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
OBJ_BUCH-1810-003.book Page 15 Tuesday, June 4, 2013 1:05 PM
Do not restart the cutting operation in the workpiece.
Let the wheel reach full speed and carefully re-enter
the cut. The wheel may bind, walk up or kickback if the
power tool is restarted in the workpiece.
Support panels or any oversized workpiece to minimize
the risk of wheel pinching and kickback. Large work-
pieces tend to sag under their own weight. Supports must
be placed under the workpiece near the line of cut and near
the edge of the workpiece on both sides of the wheel.
Use extra caution when making a "pocket cut" into ex-
isting walls or other blind areas. The protruding wheel
may cut gas or water pipes, electrical wiring or objects that
can cause kickback.
Additional safety warnings
Wear safety goggles.
Use clamps or another practical way to secure and sup-
port the workpiece to a stable platform. Holding the
work by your hand or against the body leaves it unstable
and may lead to loss of control.
Wear hearing protection, safety goggles, dust mask
and gloves. As dust mask, use at least a particle filter-
ing half mask of filter class FFP 2.
Use suitable detectors to determine if utility lines are
hidden in the work area or call the local utility company
for assistance. Contact with electric lines can lead to fire
and electric shock. Damaging a gas line can lead to explo-
sion. Penetrating a water line causes property damage or
may cause an electric shock.
When working with the machine, always hold it firmly
with both hands and provide for a secure stance. The
power tool is guided more secure with both hands.
Secure the workpiece. A workpiece clamped with clamp-
ing devices or in a vice is held more secure than by hand.
Never use the machine with a damaged cable. Do not
touch the damaged cable and pull the mains plug when
the cable is damaged while working. Damaged cables in-
crease the risk of an electric shock.
Products sold in GB only: Your product is fitted with an
BS 1363/A approved electric plug with internal fuse (ASTA
approved to BS 1362).
If the plug is not suitable for your socket outlets, it should be
cut off and an appropriate plug fitted in its place by an author-
ised customer service agent. The replacement plug should
have the same fuse rating as the original plug.
The severed plug must be disposed of to avoid a possible
shock hazard and should never be inserted into a mains sock-
et elsewhere.
Bosch Power Tools
Product Description and Specifica-
tions
Read all safety warnings and all instruc-
tions. Failure to follow the warnings and in-
structions may result in electric shock, fire
and/or serious injury.
Intended Use
With firm support of the base plate and using the blade guard,
the machine is intended for horizontal cutting or slotting of
mainly mineral materials such as marble with and without the
use of water. The machine is not intended for cutting in wood,
plastic or metal.
Product Features
The numbering of the product features refers to the illustra-
tion of the machine on the graphics page.
1 Lock-on button for On/Off switch
2 On/Off switch
3 Cutting-depth scale
4 Wing bolt for cutting depth preselection
5 Hose fitting
6 Blade guard
7 Cutting mark 0°
8 Base plate
9 Wing bolt for bevel-angle adjustment
10 Bevel-angle scale
11 Wing bolt for parallel guide
12 Venting slots
13 Spindle lock
14 Residual current device (RCD)
15 Indicator on residual current device (RCD)
16 Handle (insulated gripping surface)
17 Drive spindle
18 Mounting flange
19 Diamond cutting disc*
20 Clamping flange
21 Clamping bolt
22 Allen key
23 Connection hose
24 Hose connection for water supply
25 Water tap
26 Parallel guide**
27 Set of clamps*
*Accessories shown or described are not part of the standard de-
livery scope of the product. A complete overview of accessories
can be found in our accessories program.
**Commercially available (not included in the delivery scope)
English | 15
1 609 92A 0CV | (4.6.13)
Publicité
Table des Matières
