Setting Of Cars´ Braking Performance; Setting Fuel Tank Capacity; Extended Pit Lane Function; Sound On/Off - Carrera DIGITAL 132 Instructions De Montage Et D'utilisation
Masquer les pouces
Voir aussi pour DIGITAL 132:
- Mode d'emploi (12 pages) ,
- Instructions de montage et d'utilisation (6 pages) ,
- Guide rapide (3 pages)
Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
Setting of cars´
braking performance
1 – 10
1
3
2
1
5
5
7
8
4
3
(only for cars operated with speed controllers)
The setting of the braking performance can be effected individually
5
6
for one and/or several cars. The cars which are to be adjusted have
to be positioned on the track. The setting can be carried out on 10
levels with the 5 LEDs indicating the different levels by flashing or
permanent lighting.
1 LED lights = low braking effect
1
5 LEDs light = high braking effect
2
Switch on the Control Unit, place the cars to be adjusted on the
6
track and press "BRAKE"
once. A certain number of LEDs will
now light, showing the brake step last used. Push the "BRAKE" but-
ton
6
as many times until you have reached the braking perfor-
mance desired. Confirm by pressing "ENTER/START"
running light and the lighting of the middle LED confirms completion
of the setting, fig.
.
6
Setting fuel tank capacity
1 – 10
1
3
3
5
6
3
2
5
6
7
8
4
3
(only for cars operated with speed controllers)
The setting of the fuel tank capacity in combination with the Pit Lane
5
6
(30356) is effected for all cars simultaneously. The setting can be
carried out on 10 levels with the 5 LEDs indicating the different lev-
els by flashing or permanent lighting.
1 LED lights = low fuel capacity
1
5 LEDs light = full tank
2
Switch on the Control Unit, place the cars to be adjusted on the
track and activate the fuelling function by means of the slide switch
2
, fig.
. Press the "FUEL" button
3
LEDs will now light, showing the fuel capacity last used. Push the
"FUEL" button
7
as many times until you have reached the fuel
capacity desired. Confirm by pressing "ENTER/START"
running light and the lighting of the middle LED confirms completion
of the setting, fig
6
.
Extended fuelling function
You can choose between 3 modes via the sliding switch
fig.
:
3
• OFF = cars don´t consume any "petrol"
• ON = cars consume "petrol"
• REAL = maximum speed depending on fuel tank capacity / cars
consume "petrol") (only in combination with Pit Lane 30356 or Pit
Stop Lane 30346 and Pit Stop Adapter Unit 30361)
14
When driving in "REAL-mode" the car with a full tank is "heavier",
drives slowlier and shows a lower braking effect; a car with an empty
tank is "lighter", drives faster and shows a higher braking effect. The
current fuel tank capacity and the "fuel consumption" can only be
displayed in combination with the Driver Display 30353 and Pit Stop
30356.
1 – 10
2
Refuelling of cars with Pit Lane 30356
and Driver Display 30353
3
2
4
6
7
7
6
2
1
9
7
8
The car´s present tank capacity can be read via the bar display with
5 green and 2 red LEDs at the Driver Display. For refuelling drive
your car into the Pit Lane across the refuelling sensor fig.
bar display now starts to flash, fig.
by keeping the lane-change button pushed. fig.
refuellings are indicated by flashing or lighting of the yellow LEDs,
fig.
10
(also see Driver Display).
Note: cars with an empty tank are disregarded for lap-counting
in combination with Position Tower 30357.
3
. A short
Setting of tank capacity at the start of the race
1 – 10
2
11
2
4
1
4
13
5
7
8
1
6
(only in combination with Pit Lane 30356 and Driver Display 30353)
Irrespective of the basic setting of the tank capacity it is possible
to individually set the tank capacity for one or several cars at the
race´s start for the number of laps till the first pit stop. Push "START/
2
1
ENTER" once
nently, fig.
Clicking the lane-change button at the corresponding speed control-
ler enables you to change the fill level, fig.
7
8
7
once. A certain number of
3
. A short
2
,
Pit Lane 30356
Driver Display 30353
1
4
3
8
8
5
6
4
3
10
5
6
, and the car can be refuelled
8
9
. The number of
Pit Lane 30356
Driver Display 30353
12
4
3
3
2
14
5
6
6
7
4
3
5
6
3
; the 5 LEDs at the Control Unit will light perma-
, and the Driver Display´s bar display will flash, fig.
12
.
14
4
3
5
6
4
3
5
6
Extended Pit Lane function
Pit Lane 30356
1
2
1
3
7
8
2
1
5
7
8
4
(only in combination with Pit Lane 30356)
. The
It is possible to activate/deactivate the lap counting function in the
7
5
Pit Lane 30356 or Pit Stop Lane 30346 with the Pit Stop Adapter
Unit 30361. Switch off the Control Unit, keep "SPEED" button
pushed, switch on Control Unit and release "SPEED" button
By pushing the button again, 1 or 2 LEDs will light depending on
the setting.
• LED 1 = lap counting function deactivated
• LED 1 + 2 = lap counting function activated
Select the desired setting and push or drive a car across the Pit
Lane Sensor, fig.
. The settings will now be adopted. Push
5
"START/ENTER"
3
for leaving the settings again.
Sound ON/OFF
1
2
1
1
4
3
7
8
8
5
2
1
The confirmation sound when crossing the sensors and the key
sound can be switched off. Switch off the Control Unit and keep the
7
8
"START/ENTER" button
3
release "START/ENTER"
3
for switching on the Control Unit cannot be switched off however.
.
13
Reset function
1
2
1
3
7
8
2
1
7
8
3
2
5
6
3
4
5
6
6
3
6
7
5
)
5
.
2
3
6
7
pushed, switch on the racetrack and
again. The acknowledgement sound
2
4
3
5
6
2
2
Publicité
Chapitres
Table des Matières
