Changing The Saw Blade - Festool TS 75 EBQ Notice D'utilisation D'origine

TS 75
GB
Connecting and detaching the mains power cable -
see Fig. [2].
Slide the switch-on lock [1-8] upwards and press
the on/off switch [1-7] (press = ON / release = OFF).
Pressing the switch-on lock unlocks the
plunging mechanism. The saw unit can then
be moved downwards. This causes the saw
blade to emerge from the protective cover.

When the machine is lifted, the sawing unit
springs back into the starting position.
6 Settings
WARNING
Risk of injury, electric shock

Always pull the mains plug out of the socket be-
fore performing any type of work on the ma-
chine!
6.1 Electronics
The machine (TS 75 EBQ/ TS 75 EQ) features full-
wave electronics with the following properties:
Smooth start-up
The electronically controlled smooth start-up en-
sures that the machine starts up jolt-free.
Constant speed
The motor speed remains constant through elec-
tronic control to ensure a uniform cutting speed
even when under load.
Speed control
You can regulate the speed steplessly within the
speed range using the adjusting wheel [1-5] (see
Technical data). This enables you to optimise the
cutting speed to suit the surface (see table 1).
Temperature control
To prevent overheating, the safety electronics
switches the machine off when it reaches a critical
motor temperature. Let the machine cool down for
approx. 3–5 minutes before using it again. The ma-
chine requires less time to cool down if it is running,
i.e. in neutral position.
Current limiting
Current limiting prevents excessive current con-
sumption under extreme overload, which can lead
to a decrease in the motor speed. The motor imme-
diately restarts after the load is removed.
Brake
The TS 75 EBQ is fitted with an electronic brake.
When the saw is switched off, the brake stops the
saw blade electronically within approx. 2 seconds.
16
6.2 Setting cutting depth
The cutting depth can be set at 0 - 75 mm.

Press the cutting depth stop [3-3] and move it to
the desired cutting depth (the values specified
on the scale [3-1] apply to 0° cuts without guide
rail),

Release the cutting depth stop (the cutting
depth stop notches along in 1 mm-steps).
The sawing unit can now be pressed down to the set
cutting depth.

A grub screw (M4x8 to M4x12) can be screwed
into the hole [3-2] on the cutting depth stop. By
turning the grub screw, the cutting depth can be
set even more exactly (± 0.1 mm).
6.3 Setting cutting angle
The sawing unit can be swivelled between 0° and
47°:

Loosen rotary knobs [3-4, 3-6].

Swivel sawing unit to the desired cutting angle
[3-5],l.

Retighten rotary knobs.

both limit positions are set ex works at 0° and
45°. By turning both setscrews [3-7] counter-
clockwise, the 45° limit position can be in-
creased to a maximum of 47°.
6.4

Changing the saw blade

CAUTION
Hot and sharp tools
Risk of injury

Wear protective gloves.

Move lever [4-2] as far as it will go,

Push switch lock [4-1] up and push sawing unit
down until it locks into place,

Loosen screw [4-4] with Allen key [4-3],

Remove saw blade,

Clean flange [4-8, 4-10],

Insert new saw blade.
The direction of rotation of the saw blade
[4-9] and the machine [4-7] must be the
same!

Insert outer flange [4-10] such that the locking
pins engage into the notches on the inner flange
[4-8],

Tighten screw [4-4],

Put lever [4-2] back.
6.5 Setting the spacer wedge

Move lever [4-2] as far as it will go,