Technical Data; Ec Declaration Of Conformity - HSM Classic 390.3 Notice D'utilisation

10 Technical data

Cutting type
Shred size (mm)
Sa fe ty ra ting German DIN 32757 – 1
Cutting ca pa ci ty** (Sheet), DIN A4 70 g/m
Cutting speed
Weight
Noise level (Idle running/ load)
Lo ading width
Voltage
Power for the maximum number of sheets
Operating mode
Ambient conditions in operation:
Temperature
Relative humidity
Height above sea-level (MSL)
Dimensions W x D x H (mm)
Volume of shredded material bag
* HSM-specifi cation
** The maximum number of sheets (DIN A4, 70 g/m² or 80 g/m²), fed lengthways, which can be cut in one cycle. The
performance data is determined when the motor is cold and the cutting device is freshly oiled. A weaker mains voltage
or a different mains frequency to the one specifi ed could result in less sheet capacity and increased noise during op-
eration. The sheet capacity can vary depending on the structure and properties of the paper and on the way it enters.
The performance data in 80 g/m² is calculated.

EC Declaration of Conformity

The manufacturer HSM GmbH + Co. KG, Austraße 1 - 9, D-88699 Frickingen hereby declares that the machine,
referred to here as
document shredder HSM Classic 390.3
corresponds to the health and safety requirements of the following EC directives listed below due to its conception and
design of the version in which it was put into circulation by us:
Low voltage directive 2006 / 95 / EEC
EMC directive 2004 / 108 / EC
Applied standards and technical specifi cations:
• EN 55014-1:2006
• EN 55014-2:1997 + A1:2001 + A2:2008
• EN 61000-3-2:2006
• EN 61000-3-3:1995 + A1:2001 + A2:2005
• EN 13849-1:2008
• EN 62233:2008
Frickingen, 01.03.2010
Rolf Gasteier - Technical Director
The machine type was tested for compliance with the requirements of the EC directives by:
the test and certifi cation board of the Technical Administation Committee, c/o Verwaltungs-Berufsgenossenschaft,
Deelbögenkamp 4, D-22297 Hamburg, Germany.
This test centre is responsible according to the EC directives.
14
Strip cut
5.8 3.9
2 2
2 40 - 42 31 - 33
80 g/m 2 33 - 35 25 - 27
126 mm/s
48 kg
60 dB(A)/60-70 dB(A)
• EN 61000-4-2:1995 + A1:1998 + A2:2001
• EN 61000-4-4:2004
• EN 61000-4-5:2006
• EN 61000-4-6:2007
• EN 61000-4-11:2004
Classic 390.3
english
Cross cut
3.9 x 40 1.9 x 15
3 4
25 - 27 17 - 19
20 - 22 13 - 15
135 mm/s
56 - 58 kg
60 dB(A) / 70 - 80 dB(A)
400 mm
230 V, 50 Hz
100 V, 50/60 Hz – 115 V, 60 Hz
1400 W
Continuous operation
-10 °C to +40 °C
max. 90 %, without condensation
max. 2,000 m
595 x 510 x 915
148 l
0.78 x 11 1 x 5
5 Level 6*
10 - 11 7 - 8
7 - 9 6 - 7
09/2011