Gaggenau AC250121 Notice D'utilisation Et De Montage page 27

so oft drücken, bis in der LED-Anzeige die LED 5
2.
für die Intensivstufe 2 leuchtet.
After approx. 6 minutes, the appliance automatically
a
switches to fan setting 3.
Switching off intensive mode
To select a fan setting of your choice, press ⁠ .
▶
After approx. 6 minutes, the appliance automatically
a
switches to fan setting 3.
Switching on intermittent ventilation
With interval ventilation, the ventilation switches on for
approx. 6 minutes every hour.
Note: In the Home Connect app, you can set the time
and fan setting individually.
Press ⁠ .
▶
In the LED display, LED 6 flashes continuously, the
a
LED for the selected fan setting lights up on the ap-
pliance.
As soon as the ventilation time ends, the LED for
a
the fan setting you have selected goes out. LED 6
continues to flash.
Switching off interval ventilation
Press ⁠ .
▶
Switch on automatic mode
The optimum fan setting is set automatically using a
sensor.
Press ⁠ .
▶
In the LED display, LED 6 lights up for automatic
a
mode.
Switch off automatic mode
Press ⁠ .
▶
The appliance switches to the fan setting that was
a
previously set.
The ventilation is automatically ended when the
a
sensor detects no further change in the room air
quality.
Automatic mode runs for a maximum of four hours.
a
Intermittent ventilation
With interval ventilation, the ventilation system switches
on and off in the selected setting for the selected time.
Note: This function is only available via a mobile device
with the Home Connect app.
If the interval ventilation is switched on, LED 6 continu-
ously flashes in the LED display for the interval ventila-
tion and the LED for the selected fan setting lights up.
As soon as the ventilation time ends, the LED for the
fan setting you have selected goes out. LED 6 contin-
ues to flash.
1
Depending on the appliance specifications
a
1
1
a
a
Sensor control
In automatic mode, a sensor in the appliance detects
the intensity of the cooking and roasting fumes. De-
pending on the setting of the sensor sensitivity, the op-
timum fan setting automatically switched on.
If the sensor control system reacts too weakly or too
strongly, the setting for the sensor sensitivity may
change.
Default setting: Fan setting 3
¡
Lowest setting: Fan setting 1
¡
Highest setting: Fan setting 5
¡
Setting the sensor control
Requirement: The appliance is switched off.
Press and hold ⁠ and ⁠ for approx. three seconds.
1.
Press ⁠ or ⁠ to change the setting.
2.
To cancel the setting, press ⁠ .
To save the setting, press and hold ⁠ and ⁠ for ap-
3.
prox. three seconds.
Or wait approx. 10 seconds until the setting is
saved automatically.
A signal tone sounds as soon as the selected set-
ting is saved.
Setting the saturation indicator
The saturation indicator must be adjusted depending
on the filter used.
Requirement: The appliance is switched off.
Press and hold ⁠ and ⁠ for approx. three seconds.
1.
To set circulating-air mode (non-regenerable fil-
‒
ter), press ⁠ /⁠ until LED 2 lights up in the LED
display.
To set circulating-air mode (non-regenerable fil-
‒
ter), press ⁠ /⁠ until LED 3 lights up in the LED
display.
To convert the electronic control back to opera-
‒
tion without the air recirculation filter, press ⁠ /⁠
until LED 1 lights up on the LED display.
To save the setting, press and hold ⁠ and ⁠ for ap-
2.
prox. three seconds.
Or wait approx. 10 seconds until the setting is
saved automatically.
To cancel the setting, press ⁠ .
A signal tone sounds as soon as the selected set-
ting is saved.
Resetting the saturation indicator
After cleaning the grease filter or after changing the
odour filter, the saturation indicator can be reset.
Requirements
After the appliance has been switched off, LED 1
¡
flashes in the LED display for the grease filter satura-
tion display and/or LED 2 flashes for the saturation
indicator for the odour filter.
A repeated signal tone sounds.
¡
Press ⁠ .
▶
The saturation indicator is reset.
Basic operation en
27