Télécharger Imprimer la page

Publicité

Liens rapides

INSTALLATION INSTRUCTIONS FOR THE
MICRO SWITCH GLS MIN-DIN SERIES
GLOBAL LIMIT SWITCH
Instrucciones de instalación para los MICRO SWITCH interruptores limite global (serie GLS MIN-DIN)
Einbauanweisungen für den MICRO SWITCH Global Endschalter (Serie GLS MIN-DIN)
Instructions d'installation du MICRO SWITCH fin de course mondiales (série GLS MIN-DIN)
Istruzioni per l'installazione del MICRO SWITCH finecorsa globali (Serie GLS MIN-DIN)
Instruções de Instalação para o MICRO SWITCH de limite global (Série GLS MIN-DIN)
MICRO SWITCH 全球限位开关( GLS MIN-DIN 系列)安装指南
m WARNING
IMPROPER INSTALLATION
Consult with local safety agencies and their
requirements when designing a machine-control link,
interface, and all control elements that affect safety.
Strictly adhere to all installation instructions.
Failure to comply with these instructions could result in
death or serious injury.
MOUNT, WIRE, AND SEAL THE SWITCH
m WARNING
IMPROPER OPERATION
Ensure switch actuator achieves sufficient travel for
positive opening of normally closed (NC) contacts to
occur.
Failure to comply with these instructions could result in
death or serious injury.
Ui 300V ac/dc metal
Ui 300 Vdc/600 Vac plastic
UL EN 50047
EN60947-5-1
CCC GB 14048.5
EN45545-2 HL 3 (GLC & GLE Series switches only)
EN61373 (GLC & GLE Series switches only)
1.
Refer to:
Page 5 for adjustments
Pages 8 to 12 for specific travel distances for each
switch code and specifications
Page 5 for proper application of limit switches
Page 13 to 18 for switch mounting dimensions
2.
Perform adjustments (if desired):
Head orientation (Figure 1, page 5)
Actuation direction (Figure 2, page 5)
Side rotary switches with 36 drive lever positions
(Figure 3, page 5):
3.
Mount switch at top corners of switch using two M4 or #8
screws. For GLD products torque screws to 2,7 Nm to 3,4
Nm [24 in-lb to 30 in-lb]. For GLC & GLE products torque
screws to 3,1 Nm to 3,7 Nm [27 in-lb to 33 in-lb].
4.
Remove screws on cover plate.
5.
Connect stranded wire (0,75 mm
or solid wire (0,75 mm
block terminals (use 90 °C wire when ambient temperature
is over 75 °C). Torque switch terminal screws to 0,8 Nm to
1,0 Nm [7 in-lb to 9 in-lb].
6.
Seal conduit opening according to instructions in PK
80112.
7.
Reassemble cover plate, and torque cover screws to 0,5 Nm
[4.4 in-lb].
81521
Issue 11
2
to 2,3 mm
2
, 18-14 AWG)
to 1,5 mm
, 18-16 AWG) to contact
2
2

Publicité

loading

Sommaire des Matières pour Honeywell GLS MIN-DIN Série

  • Page 1 81521 INSTALLATION INSTRUCTIONS FOR THE MICRO SWITCH GLS MIN-DIN SERIES Issue 11 GLOBAL LIMIT SWITCH Instrucciones de instalación para los MICRO SWITCH interruptores limite global (serie GLS MIN-DIN) Einbauanweisungen für den MICRO SWITCH Global Endschalter (Serie GLS MIN-DIN) Instructions d’installation du MICRO SWITCH fin de course mondiales (série GLS MIN-DIN) Istruzioni per l’installazione del MICRO SWITCH finecorsa globali (Serie GLS MIN-DIN) Instruções de Instalação para o MICRO SWITCH de limite global (Série GLS MIN-DIN) MICRO SWITCH 全球限位开关(...
  • Page 2 Vuelva a montar la tapa y ajuste empleando un torque de Bringen Sie die Abdeckplatte wieder an, und schrauben 0,5 Nm [4,4 in-lb]. Sie diese mit einem Anzugsmoment von 0,5 Nm [4,4 in-lb] fest. MICRO SWITCH GLS Min-Din Installation Instructions | sps.honeywell.com/ast...
  • Page 3: Avertissement Mauvais Fonctionnement

    PK 80112. Replacez le couvercle et serrez les vis avec un couple de 0,5 Rimontare il coperchio e serrare le viti con una coppia di Nm [4,4 in-lb]. 0,5 Nm [4,4 in-lb]. MICRO SWITCH GLS Min-Din Installation Instructions | sps.honeywell.com/ast...
  • Page 4 Vede as aberturas do conduíte de acordo com as in- struções encontradas no PK 80112. Monte novamente a tampa de cobertura e aperte os para- fusos com torque de 0,5 Nm [4,4 lb-pol.]. MICRO SWITCH GLS Min-Din Installation Instructions | sps.honeywell.com/ast...
  • Page 5 Operação Maximum Discon- Fuerza de descon- Maximale Öff- Force de décon- Forza massima di Força Máxima de 最大切断力 nect Force exión máxima nungskraft nexion maximum scollegamento Desconexão MICRO SWITCH GLS Min-Din Installation Instructions | sps.honeywell.com/ast...
  • Page 6 • Diretiva de maquinário somente no que se refere 机械指令,仅限与安全功能中使用的元件 direttiva fa riferimento ai componenti da utilizzare composants utilisés dans une fonction de sécurité. aos componentes usados em função de segurança. 相关的指令。 con funzioni di sicurezza. MICRO SWITCH GLS Min-Din Installation Instructions | sps.honeywell.com/ast...
  • Page 7: Product Nomenclature

    5 POM roller NOTE: not all combinations of model code are available. Side rotary, Lever to DPST, 2NC Cat whisker, adjust., 140 mm Please contact your Honeywell provider/representative slow acting 140 mm mounting surf. aluminum rod for assistance. Side rotary,...
  • Page 8 GLE*32A [1.6 [1.6 mm/s mm/s 13-14 in-lb] in-lb] 21-22 23-24 RP=8,4 mm FP = 0° OP = 26° RP = 18° DT = 8° * = 54° Total travel = 70° min. MICRO SWITCH GLS Min-Din Installation Instructions | sps.honeywell.com/ast...
  • Page 9 2 NC/2 NO, snap action 21 mm 1,0 mm/S GLE*24B 13 N 24 N mm/S [0.04 RP=18,6 mm GLE*32B [2.9 lb] [5.4 lb] [3.9 18 mm in/S] in/S] 15 mm OT max. DT=0,6 mm MICRO SWITCH GLS Min-Din Installation Instructions | sps.honeywell.com/ast...
  • Page 10 11-12 28 mm 13-14 27 mm 26,2 mm 21-22 23-24 25 mm OT max. DT=1,0 mm 13,6 11-12 13-14 5,3 mm 12,2 17,3 21-22 21-22 23-24 13-14 RP=9,5 mm 10,5 MICRO SWITCH GLS Min-Din Installation Instructions | sps.honeywell.com/ast | 10...
  • Page 11 2 NO, snap action DT=0,9 action 35,8 mm -0,3 mm 10,4 18,3 34,2 32,9 11-12 13-14 17,6 21-22 23-24 -0,3 mm 14,4 21-22 DT=2,4 13-14 11-12 10,4 13-14 21-22 23-24 RP=8,0 MICRO SWITCH GLS Min-Din Installation Instructions | sps.honeywell.com/ast | 11...
  • Page 12 0° 16° 35° 11-12 13-14 2 NC/2 NO, snap action 21-22 1,1 N 23-24 GLE*24K 0.13 [0.25 360° 10° DT=7° max. GLE*32K rad/s rad/s 11-12 13-14 21-22 23-24 RP=9° MICRO SWITCH GLS Min-Din Installation Instructions | sps.honeywell.com/ast | 12...
  • Page 13 3,5 mm [0.14 in] for PG 13,5 and M20 conduit threads. 7,2 mm [0.28 in] for 0.5-14 NPT conduit threads. 3,5 mm [0.14 in] for PG 13,5 and M20 conduit threads. 7,2 mm [0.28 in] for 0.5-14 NPT conduit threads. MICRO SWITCH GLS Min-Din Installation Instructions | sps.honeywell.com/ast | 13...
  • Page 14 7,2 mm [0.28 in] for 0.5-14 NPT conduit threads. 3,5 mm [0.14 in] for PG 13,5 and M20 conduit threads. 7,2 mm [0.28 in] for 0.5-14 NPT conduit threads. Figure 11. GLC Conduit MICRO SWITCH GLS Min-Din Installation Instructions | sps.honeywell.com/ast | 14...
  • Page 15 M20 conduit threads. 7,2 mm [0.28 in] for 0.5-14 NPT conduit threads. 3,5 mm [0.14 in] for PG 13,5 and M20 conduit threads. 7,2 mm [0.28 in] for 0.5-14 NPT conduit threads. MICRO SWITCH GLS Min-Din Installation Instructions | sps.honeywell.com/ast | 15...
  • Page 16 Figure 21. GLD Wobble • K8A/K8B 3,5 mm [0.14 in] for PG 13,5 and M20 conduit threads. 7,2 mm [0.28 in] for 0.5-14 NPT conduit threads. Figure 22. GLD Conduit MICRO SWITCH GLS Min-Din Installation Instructions | sps.honeywell.com/ast | 16...
  • Page 17 Figure 24. GLE Side Rotary • A2, A2A, A2B, and A2Y Figure 27. GLE Side Rotary • A9A Figure 25. GLE Side Rotary • A4J and A4L Figure 28. GLE Top Pin Plunger MICRO SWITCH GLS Min-Din Installation Instructions | sps.honeywell.com/ast | 17...
  • Page 18 Figure 29. GLE Top Roller Plunger Figure 31. GLE Wobble • E7B Figure 30. GLE Top Roller Arm Figure 32. GLE Wobble • K8A Figure 33. GLE Conduit Adapter for 0.5-14 NPT MICRO SWITCH GLS Min-Din Installation Instructions | sps.honeywell.com/ast | 18...
  • Page 19 While Honeywell may provide application assistance personally, cas tenu responsable de tout dommage indirect, spécial ou acces- through our literature and the Honeywell web site, it is up to the cus- soire. tomer to determine the suitability of the product in the application.
  • Page 20 +44 1344 238258 Japan +81 (0) 3-6730-7152 Singapore +65 6355 2828 Greater China +86 4006396841 Honeywell Advanced Sensing Technologies 830 East Arapaho Road Richardson, TX 75081 PK 81521-11-EN | 11 | 06/21 sps.honeywell.com/ast © 2021 Honeywell International Inc. All rights reserved.