Changing The Gas Supply - Brandt TE560WF1 Guide D'installation Et D'utilisation

1 / INSTALLING YOUR APPLIANCE
• •

CHANGING THE GAS SUPPLY

W W a a r r n n i i n n g g
Y Y o o u u r r a a p p p p l l i i a a n n c c e e i i s s s s o o l l d d p p r r e e - - s s e e t t f f o o r r
n n a a t t u u r r a a l l g g a a s s . .
T T h h e e i i n n j j e e c c t t o o r r s s r r e e q q u u i i r r e e d d f f o o r r a a d d a a p p t t i i o o n n t t o o b b u u t t a a - -
n n e e / / p p r r o o p p a a n n e e c c a a n n b b e e f f o o u u n n d d i i n n t t h h e e p p l l a a s s t t i i c c b b a a g g
c c o o n n t t a a i i n n i i n n g g t t h h i i s s g g u u i i d d e e . .
T T i i p p
I I n n F F r r a a n n c c e e , , t t h h i i s s h h o o b b c c a a n n a a l l s s o o b b e e a a d d a a p p - -
t t e e d d t t o o p p r r o o p p a a n n e e / / b b u u t t a a n n e e - - a a i i r r g g a a s s . . T T h h e e a a d d a a p p t t a a - -
t t i i o o n n k k i i t t i i s s s s u u p p p p l l i i e e d d o o n n r r e e q q u u e e s s t t b b y y y y o o u u r r
A A f f t t e e r r - - S S a a l l e e s s S S e e r r v v i i c c e e D D e e p p a a r r t t m m e e n n t t . .
Each time you change the gas supply, you
must complete the following:
— Adapt the gas connection
— Change the injectors
— Adjust the hob connections
•
A A d d a a p p t t t t h h e e g g a a s s c c o o n n n n e e c c t t i i o o n n : Refer to the
" " G G a a s s C C o o n n n n e e c c t t i i o o n n " " section.
•
C C h h a a n n g g e e t t h h e e i i n n j j e e c c t t o o r r s s , proceeding as fol-
lows:
— Remove the pan suppor ts, heads and
covers from all burners.
— Using the wrench provided, unscrew the
injectors located under each crucible and
remove them (Fig. 01).
— Replace with the corresponding gas injec-
tors, in compliance with the placement of the
injectors and the table of gas properties at the
end of this section; to do so:
— First screw them in manually until the injec-
tor locks into place.
— Apply the wrench to the injector as far as it
will go.
— Draw a line on the burner plate using a pen-
cil at the place indicated (Fig. 02).
— Turn the wrench clockwise until the line
appears on the other side (Fig. 03).
W W a a r r n n i i n n g g
E E x x c c e e e e d d i i n n g g t t h h i i s s l l i i m m i i t t m m a a y y d d a a m m a a g g e e t t h h e e
p p r r o o d d u u c c t t . .
— Reposition the burner heads, burner covers
and pan supports on the hob.
Tip
Each time you change the gas supply,
tick the box corresponding to the new gas
level on the label found in the plastic bag.
Refer to the corresponding "Gas
Connection" section.
Fig. 01
Fig. 02
Fig. 03
31 31
Wrench
Crucible
Injector
Line
Wrench
Line
Wrench