Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
1 / INSTALLING YOUR APPLIANCE
• • TIPS FOR FLUSH MOUNTING
Underside view
of the housing
Fig. 01
A A
Mounting brackets
Cabinet
Fig. 02
Place your hob in the opening of the support
cabinet, carefully pulling the table towards
you.
Reposition the burner heads, burner covers
and pan supports on the hob.
Connect your hob to the gas supply (See "Gas
Connection" chapter) and to the power supply
(See "Electrical Connection" chapter).
If you wish, you can immobilise the hob using
the four mounting brackets delivered with a
screw (Fig. 02) to attach them to the four cor-
ners of the housing. Y Y o o u u m m u u s s t t u u s s e e t t h h e e h h o o l l e e s s
p p r r o o v v i i d d e e d d f f o o r r t t h h i i s s p p u u r r p p o o s s e e , , a a c c c c o o r r d d i i n n g g t t o o t t h h e e
d d i i a a g g r r a a m m a a b b o o v v e e (Fig. 01) . .
S S t t o o p p s s c c r r e e w w i i n n g g w w h h e e n n t t h h e e m m o o u u n n t t i i n n g g b b r r a a c c k k e e t t
s s t t a a r r t t s s t t o o b b e e c c o o m m e e d d e e f f o o r r m m e e d d . .
D D o o n n o o t t u u s s e e a a s s c c r r e e w w d d r r i i v v e e r r .
A A
A A
A A
Mounting brackets
• •
ELECTRICAL CONNECTION
Your hob is sold with a power cable (type
A A
H05V2V2F - T90, cross-section 1 mm²) with
three conductors (phase + ground + neutral).
Af ter-sales ser vice reference: 77X3767
(6470.1516). It must be connected to a 220-
240 V~ monophase grid via a standardised
IEC 60083 electrical outlet with phase
+ ground + neutral or or an all-pole cut-off
device with a minimum distance between con-
tact openings of 3.5 mm.
The plug of the electrical outlet must be
accessible after installation.
C C
A A B B L L E E C C R R O O S S S S
H05V2V2F -T90 cable
Cross-section of
conductors in mm
Fuse
Warning
The safety wire (green/yellow) is con-
nected to the appliance's ground terminal
and must be connected to the ground
lead
of the electrical set-up.
The fuse in your set-up must be
10 amperes.
If the power cable is damaged, it must be
replaced by a cable or a special kit avail-
able from the manufacturer or its After-
Sales Service Department.
Tip
In order to easily locate the reference
information for your appliance, we recom-
mend that you note them on the "After-
Sales Service Department and Customer
Relations" page (this page also explains to
you where to find this information on your
appliance).
28
- -
S S E E C C T T I I O O N N T T O O B B E E U U S S E E D D
2 2 2 2 0 0 - - 2 2 4 4 0 0 V V ~ ~ - - 5 5 0 0 H H z z
G G a a s s a a n n d d d d u u a a l l
3 conductors
including one
ground wire
1
²
10 A
Publicité
Chapitres
Table des Matières
