Product Familiarisation; Accessories - Triton T4PHJ Instructions D'utilisation

Introduction
Thank you for purchasing this Triton product. This manual contains information
necessary for safe and effective operation of this product. This product has unique
features and, even if you are familiar with similar products, it is necessary to read this
manual carefully to ensure you fully understand the instructions. Ensure all users of
the product read and fully understand this manual.

Product Familiarisation

1. Clamp Handle
2. Thickness Plate
3. Collar Setting Indicator
4. Clamp
5. Drill Guide
6. Depth Collar
7. Hex Key
8. 150mm (6") Square Drive
9. Step Drill Bit
10. Wooden Plug
11. Self-Tapping Screw
Intended Use
Easy to set pocket-hole jig with built-in clamp for use in joinery work. Can be used for joints
such as panel fixing and corners.
Before Use
WARNING: Always adhere to all safety advice and instructions for any power tool used in
conjunction with this product.
Operation
WARNING: Never hold the jig by hand when drilling; it must be fixed securely to a suitable
workbench. Failure to do so could damage the tool and/or cause serious personal injury.
IMPORTANT: Always practise on a scrap piece of wood before making a pocket hole in the
workpiece.
Note: Ideally, the drill tip should emerge close to the middle of the material being drilled.
Note: Screws should go into the edge grain or the face grain, not the end grain, for a more
secure joint (Image I).
1. Determine the thickness of the wood where the pocket hole will be created
2. Use the Collar Setting Indicator (3) to determine the position of the Depth Collar (6) on the
Step Drill Bit (9) (See Images B - E). Tighten with the Hex Key (7) when in position
Note: Measure from the start of the step on the Step ped Drill Bit to the end of the Collar
Setting Indicator (Image A).
3. Rotate the Thickness Plate (2) in position to the corresponding wood thickness (See
Images B - E)
4. Open the Clamp Handle (1), and position the workpiece between the jig and work bench
(Image F)
5. Raise the Clamp (4) to the underside of the work surface until tight, and lower the Clamp
Handle (Image G)
IMPORTANT: Ensure the Clamp, Jig and workpiece are securely fixed in place.
6. Attach the Step Drill Bit into the drill
7. Place the Step Drill Bit into the Drill Guide (5). Begin drilling and continue until the Depth
Collar makes contact with the jig (Image H)
8. Remove the Step Drill Bit and raise the Clamp Handle to release the workpiece
9. Repeat to create the required number of holes and finish using the Self-tapping Screws
(11) and the Wooden Plugs (10)
EN
6
Original Instructions
Timber Thickness
13 – 18mm / 1/2" – 11/16"
19 – 25mm / 3/4" – 1"
26 – 30mm / 1" – 1-1/4"
31 – 37mm / 1-1/4" – 1-7/16"
≥38mm / ≥1-1/2"
Note: For hard wood use a fine thread, and for soft wood use a coarse thread.
Tips
• Clamp across the joint when assembling a joint (Image J)
• The pocket-hole jig can be used for joining panels (Image K)

Accessories

A full range of accessories including jigs, plugs, screws and bits is available from your Triton
stockist.
Maintenance
Keep the Drill Guides clear of chip and dust build-up.
Contact
For technical or repair service advice, please contact the helpline on (+44) 1935 382 222
Web: tritontools.com/en-GB/Support
Address:
Powerbox
Boundary Way
Lufton Trading Estate
Yeovil, Somerset
BA22 8HZ, United Kingdom
Screw
25mm / 1"
30mm / 1-1/4"
35mm / 1-1/2"
50mm / 2"
60mm / 2-1/2"