Metabo HPT C 10FCH2 Instructions De Sécurité Et Mode D'emploi page 13

Ceiling
Wall
1 2
Inside corner
Fig. 26
The table below shows the miter angle and the bevel angle settings that
are ideal for the two crown molding types.
To process crown molding at
positions 1 and 4 in Fig. 26.
Type of Crown
Molding
Miter Angle
Setting
right 35.3°
45° Type
( mark)
right 31.6°
38° Type
( mark)
(1) Setting to cut crown moldings at positions 1 and 4 in Fig. 26 (see
Fig. 27; tilt the motor head to the left):
1 Turn the turntable to the right and set the Miter Angle as follows:
∗ For 45° type crown moldings:
∗ For 38° type crown moldings:
2 Tilt the motor head to the left and set the Bevel Angle as follows:
∗ For 45° type crown moldings:
∗ For 38° type crown moldings:
3 Position the crown molding so that the upper surface (Ⓐ in Fig. 25)
contacts the fence as indicated in Fig. 29.
(2) Setting to cut crown moldings at positions 2 and 3 in Fig. 26 (see
Fig. 28; tilt the head to the left):
1 Turn the turntable to the left and set the Miter Angle as follows:
∗ For 45° type crown moldings:
∗ For 38° type crown moldings:
2 Tilt the head to the left and set the Bevel Angle as follows:
∗ For 45° type crown moldings:
∗ For 38° type crown moldings:
3 Position the crown molding so that the lower surface (Ⓑ in Fig. 25)
contacts the fence as in Fig. 30.
1
Miter angle scale
Turntable
Fig. 27
2
Fence (B)
Fig. 28
3 4
Outside corner
Bevel Angle
Setting
left 30°
( mark)
left 33.9°
( mark)
35.3° ( mark)
31.6° ( mark)
30° ( mark)
33.9° ( mark)
35.3° ( mark)
31.6° ( mark)
30° ( mark)
33.9° ( mark)
Head
Bevel angle scale
4
Fence (A)
Base
Head
Bevel angle scale
3
Base
Turntable
Miter angle scale
NOTE:
For convenience, positive stops are provided for the miter setting
(left and right 31.6°) positions.
For miter cut setting
If the turntable has been set to either of the angles described, move the
turntable adjusting side handle a little to the right and left to stabilize the
position and to properly align the miter angle scale and the tip of the
indicator before the operation starts.
For bevel cut setting
Move handle on bevel section to the left and check that the position
is stable and that the bevel angle scale and the tip of the indicator are
properly aligned. Then tighten the clamp lever.
To process crown molding at positions 2
and 3 in Fig. 26.
Miter Angle
Setting
left 35.3°
( mark)
left 31.6°
( mark)
Fence
Ⓐ
Fig. 29
Fence
Ⓑ
Table on base
Fig. 30
Cutting method of crown molding without tilting the saw blade.
(1) Crown molding Stopper (L) and (R) (optional accessories) allow easier
cuts of crown molding without tilting the saw blade. Install them in the
base both-sides side to be shown in Fig. 31-a. After inserting Tighten the
6mm knob bolts to secure the crown molding Stoppers.
[Optional accessories used]
• Crown molding Vise Ass'y (Include Crown molding Stopper (L))
• Crown molding Stopper (L)
• Crown molding Stopper (R)
Crown molding
vise ass'y
6mm Wing
(Optional
bolt
accessories)
6mm Wing
bolt
Crown molding
6mm Wing bolt
stopper (L)
(Optional accessories)
Fig. 31-a
Bevel Angle
Setting
left 30°
( mark)
left 33.9°
( mark)
Ⓑ
Table on base
Ⓐ
Crown molding
stopper (R)
(Optional accessories)
English
13