Anleitung -
Schraubensatz -
Screw set -
9x
M3x11
1
Montage:
Legen Sie die Hardware auf eine antistatische Unterlage.
Beginnen Sie mit der Demontage des Original-Kühlers. Je nach
Aufbau des Kühlers sind zuerst die Schrauben des Lüfters zu
entfernen und die Blenden zu lösen. Bei aufgeklebten Kühlern ist
äußerste Sorgfalt geboten. Es können leicht Bauteile abgerissen
werden. Heben Sie alle Einzelteile sorgfältig auf. Reinigen Sie
anschließend die Hardware von Resten der Wärmeleitpaste oder
Pad's mit einem Lösemittel (z.B. Spiritus).
2
Tragen Sie nun unter Zuhilfenahme eines Plastikstreifens oder
ähnlichem, eine gleichmäßige Schicht Wärmeleitpaste auf die zu
kühlenden GPU auf. Die Schicht sollte weniger als einen Millimeter
dick sein, da sonst die umliegenden Bauteile unnötig verunreinigt
werden können.
3
Entfernen Sie die Schutzfolie der verschieden farbig dargestellten
Wärmeleitpad's und schneiden Sie diese passend für die
Spannungswandler zu. Vergessen Sie auch hier nicht die Schutzfolie
zu entfernen.
GPX - A Vega pro M01
Instruction manual -
Jeu de vis
2x
4x
2x
30mm x 30mm x
M3x6
0,5mm
SW 2 / SW 2,5
1x
2x
15mm x 15mm x
30mm x 30mm x
1mm
1mm
Assembly: Put the hardware on an antistatic mat. Start with the
dismantling of the original cooler. Depending on the structure of the
cooler remove the screws at the back of the card and carefully unhook
the fan connector. If the original cooler uses thermal glue extreme
care should be taken. As you can easily damage parts. Pick up all the
items carefully. Then clean the hardware of thermal paste or pad
residues with a solvent (eg alcohol ).
With the help of a plastic strip or thermal paste spreader make a thin
layer of thermal paste on the GPU. The layer should be less than a
millimeter thick, otherwise the surrounding components can be
contaminated unnecessarily.
Remove the protective foil from the heat conductors shown in
different colors and cut them to fit the voltage transformers. Do
not forget to remove the protective film.
Instructions de service
1x
4x
30mm x 30mm x
30mm x 30mm x
1,5mm
2mm
Assemblage : Insérez le matériel sur un tapis antistatique .
Commencez par le démantèlement du refroidisseur d'origine . En
fonction de la structure du radiateur est de retirer les vis de fixation du
ventilateur pour retirer et régler l'ouverture. Lorsque refroidisseurs
collés soin extrême doit être exercé . Il peut facilement être déchiré
parties . Ramassez tous les articles soigneusement . Ensuite, nettoyer
le matériel de résidus de la pâte thermique ou de tampon avec un
solvant (alcool ).
Porter les maintenant à l'aide d'une bande de matière plastique ou
analogue, une couche uniforme de pâte thermique à la GPU à refroidir.
La couche doit être inférieure à un millimètre d'épaisseur, faute de quoi
les composants environnants peuvent être contaminés inutile.
Retirez le film protecteur de différentes couleurs du pad
thermique indiquées et les couper pour adapter le convertisseur
de tension. Ne pas oublier d'enlever ici le film protecteur.
1
1x
1x
30mm x 30mm x
3mm