Using The Rotary Spit; Care And Cleaning; Cleaning Agents - Bosch HGA3321.0M Notice D'utilisation

Using the rotary spit

Place the support for the rotary spit on the baking tray (fig. A).
1.
Place the rotary spit on the baking tray (fig. B).
2.

Care and cleaning

With attentive care and cleaning, your hob and oven will retain
its looks and remain in good working order for a long time. We
will explain here how you should care for and clean them
correctly.
Notes
Slight differences in the colours on the front of the oven are
■
caused by the use of different materials, such as glass,
plastic and metal.
Shadows on the door panel which look like streaks, are
■
caused by reflections made by the oven light.
Enamel is baked on at very high temperatures. This can
■
cause some slight colour variations. This is normal and does
not affect operation. The edges of thin trays cannot be
completely enamelled. As a result, these edges can be
rough. This will not impair the anti-corrosion protection.

Cleaning agents

Damage to the various different surfaces caused by using the
wrong cleaning agent can be avoided by observing the
following instructions.
When cleaning the hob do not use
undiluted washing-up liquid or dishwasher detergent,
■
scouring pads,
■
abrasive cleaning agents such as oven cleaner or stain
■
remover,
high-pressure cleaners or steam jets.
■
Do not clean individual parts in the dishwasher.
■
When cleaning the oven do not use
sharp or abrasive cleaning agents,
■
cleaning agent with a high alcohol content,
■
scouring pads,
■
high-pressure cleaners or steam jets.
■
Do not clean individual parts in the dishwasher.
■
Wash new sponges thoroughly before first use.
Insert the baking tray in position 1 and push it in as far as it
3.
will go. The back panel of the oven has an opening into which
the rotary spit is inserted (fig. C)
Remove the hand grip and close the oven door (fig. D)
4.
Zone Cleaning agent
Stainless steel sur- Hot soapy water:
faces* Clean with a dish cloth and dry with a
soft cloth. On stainless steel surfaces,
(depending on
always wipe parallel to the natural grain.
appliance model)
Otherwise, you may scratch the surface.
Remove patches and splashes of limes-
cale, grease, starch and albumin (e.g.
egg white) immediately. Corrosion can
form under such patches and splashes.
Special care products suitable for hot
stainless steel surfaces are available
from our after-sales service and from
specialist retailers. Apply a thin layer of
care product with a soft cloth.
Enamel, painted, Hot soapy water:
plastic and screen- Clean with a dish cloth and dry with a
printed surfaces* soft cloth. Do not use glass cleaner or
glass scrapers for cleaning.
(depending on
appliance model)
Control panel Hot soapy water:
Clean with a dish cloth and dry with a
soft cloth. Do not use glass cleaner or
glass scrapers for cleaning.
Upper glass cover* Glass cleaner:
Clean with a soft cloth.
(depending on
You can remove the upper glass cover
appliance model)
for cleaning. To find out how to do this,
please refer to the section Upper glass
cover.
Rotary knobs Hot soapy water:
Do not remove. Clean with a dish cloth and dry with a
soft cloth.
Hob surround Hot soapy water:
Do not clean with a glass scraper, lemon
juice or vinegar.
Gas hob and pan Hot soapy water.
supports* Use very little water. Water must not be
allowed to enter the appliance through
(depending on
the base of the burners.
appliance model)
Clean off boiled-over liquids and spilt
food immediately.
You can remove the pan supports.
Cast iron pan supports*:
Do not clean in the dishwasher.
* Optional (available for some appliances, depending on the
appliance model)
35