Specifications; Functions; Replacing The Belt - Denon DN-S3000 Mode D'emploi

ENGLISH

SPECIFICATIONS

15
GENERAL
Type: Compact disc player
Disc type: Standard compact discs (12 cm discs), CD-TEXT
CD-R, CD-RW discs
NOTE: Finalized CD-R or CD-RW discs can be played back in this unit.
Dimensions: Player unit:
Installation: Table top type
Mass: Player unit:
Power supply: U.S.A., Canada and Taiwan R.O.C. models: 120 V AC ±10%, 60 Hz
European models:
Power consumption: 16 W
Environmental conditions: Operational temperature: 5 to 35°C
Operational humidity:
Storage temperature:
AUDIO SECTION
Main out, Monitor out
Quantization: 24-bit linear per channel
Sampling frequency: 44.1 kHz at normal pitch
Oversampling rate: 8 times
Total harmonic distortion: 0.01% or less
Signal to noise ratio: 90 dB or more
Channel separation: 85 dB or more
Frequency response: 20 to 20,000 Hz
Analog output
Output level: 2.0 V r.m.s.
Load impedance: 10 kΩ/kohms or more
Digital output
Signal format: IEC958-Type
0.5 Vp-p 75 Ω/ohms
Output level:

FUNCTIONS

Instant start: Within 20 msec.
Variable pitch: ±4% (0.02% pitch), ±10% (0.1% pitch), ±16% (0.1% pitch)
±24% (0.1% pitch), ±50% (0.5% pitch) ±100% (1.0% pitch)
Pitch bend: Pitch range ±32%
Pitch range ±100%:
Sampler
Sampling: 44.1 kHz
Length: 15 sec.
Output level: 2.0 V r.m.s. (Variable / -14 ~ +6 dB)
Variable pitch: ±24% (0.1% pitch)
Search precision: 1/75 sec. (1 subcode frame)
Max. scan speed: Over 20 times normal speed
Max. MEMO memory steps: 5000 steps
✽ Specifications and design are subject to change without notice for purpose of improvement.
20
However, according to recording quality, some CD-R/RW discs
cannot be played.
285 (W) x 111.5 (H) x 327 (D) mm (without feet)
11-7/32" (W) x 4-25/64" (H) x 12-7/8" (D)
6.0 kg (12 lbs 9 oz)
230 V AC ±10%, 50 Hz
(41 to 95°F)
25 to 85% (no condensation)
–20 to 60°C (4 to 140°F)
II
±99%

REPLACING THE BELT

16
• On the DN-S3000, the platter is driven by a belt. In the unlikely case of trouble, use the procedure described
below to replace the belt.
1. Remove a screw (Hexagon socket head) and
A
pull out Scratch Disc and Slip Mat.
(Hexagon socket head)
2. Remove Belt from Motor Pully.
Belt
Motor Pully
3. Remove 3 screws B (< head) and pull out
Platter.
4. Remove Belt from Platter.
Platter
Belt
5. Mount in the order 4 → 1.
CAUTIONS:
• Unplug the power cord before replacing the
belt.
• Do not touch the sensor or scale(∗) when
removing the Platter.
• Do not apply oil or grease to the belt when
replacing it.
Stabilizer
A
Scratch Disc
Slip Mat
Slip Sheet
B
(< head)
B (< head)
Platter
∗