Installation; Assembling The Manual Release Handle; Unlocking The Motorisation - Fig; Installing The Motorisation - SOMFY ELIXO SMART io Manuel D'installation

EN

3. INSTALLATION

Attention
The motorisation must be disengaged during installation.

3.1. Assembling the manual release handle

1) Insert the release handle into the specific housing on the motor.
2) Tighten the release handle.
3) Fit the screw cover.

3.2. Unlocking the motorisation - Fig. 6

1) Turn the key a quarter of a turn to the left.
2) Turn the release handle to the right.
Attention
Do not forcibly push the gate. Hold the gate over its entire travel
during manual manoeuvres.

3.3. Installing the motorisation

3.3.1. Installing the mounting system
͉
͉
The mounting kit provided is to be used on a concrete base. For all
other types of mounting, use the appropriate fittings.
1) Position the template:
• parallel to the gate,
• with the symbol on the pinion pointing towards the gate,
• by moving it by 25 mm in relation to the front line of the rack (if the
rack is fitted with a cover, measure from the line on the rack, not on
the cover),
• so that it does not obstruct movement and to ensure the gate is able
to open and close completely.
2) Mark the location for the ground mountings.
3) Drill to a depth of 60 mm.
4) Push in the coach screws.
5) Place a washer and nut onto each coach bolt.
6) Tighten the nuts to secure the coach screws into the ground.
7) Add a nut to each coach bolt and screw them on in order to position
them 23 mm from the ground.
8) Fit the metal plate onto the nuts.
9) Check that the metal plate is level.
10) Fit the motor onto the metal plate.
11) Check the dimensions indicated in fig. 8 of the installation manual -
illustrations.
12) Add a washer and nut to each coach bolt without tightening them.
3.3.2. Installing the motor
1) Push the motor towards the gate.
2) Ensure the pinion is correctly positioned under the rack.
3) Set the height of the motor and/or the rack to ensure a clearance of
approximately 2 mm between the rack and the pinion.
Attention
This setting is important to prevent premature wear of the pinion
and rack; the pinion must not be supporting the weight of the gate.
4) Check:
• the adjustment nuts are all in contact with the metal plate,
• the gate runs correctly,
• the clearance between the rack and pinion does not vary significantly
over the gate's travel.
5) Tighten the nut on each coach bolt to fix the motor in place.
5
- Fig. 7 and 8
- Fig. 9 and 10
3.3.3. Installing the rigid end stops
Attention
Installation of rigid end stops on the ground when opening and
closing is mandatory.
The closing position is memorised at the start of the gate travel
auto-programming process.
The opening position is memorised during gate auto-programming
when the gate presses against the end stop on the ground.
1) Manually move the gate to the open position.
2) Fasten the opening end stop such that the gate presses against it.
3) Manually move the gate to the closed position.
4) Fasten the closing end stop such that the gate presses against it.
3.3.4. Connecting to the power supply
1) Connect the live (L) to terminal 1 of the control unit.
2) Connect the neutral (N) to terminal 2 of the control unit.
3) Connect the earth wire to the earth terminal on the base of the motor.
Attention
The earth wire must always be longer than the live and neutral
to ensure that it is the last to be disconnected if the connector is
pulled out.
The cable clamps supplied must be used.
For all low-voltage cables, ensure that they can withstand traction
of 100 N. Check that the conductors do not move when this traction
is applied.
3.3.5. Re-engaging the motorisation
1) Place the gate approximately 1 m from its closed position.
2) Turn the release handle to the left.
3) Move the gate manually until the drive mechanism locks.
4) Turn the key a quarter of a turn to the right.

4. QUICK COMMISSIONING

4.1. Switching the installation on

Switching the installation on.
The "POWER" indicator light flashes slowly.
4.2. Memorising the Keygo io remote controls for
operation in complete opening mode - Fig.14
͉
͉
If this procedure is carried out using a channel which has already been
memorised, this channel will be cleared.
1) Press the "PROG" button for 2 s.
The "PROG" indicator light is permanently lit.
2) Press the outer left and right buttons on the remote control together
until the indicator light flashes.
3) Press the button of the remote control that will open the gate fully.
The "PROG" indicator light flashes for 5 s.
The remote control has been memorised.

4.3. Checking the direction of motor rotation - Fig. 15

1) Press and hold the "SET" button for 2 s.
The "POWER" indicator light flashes quickly.
2) Press and hold the "+" button to open the gate.
If the gate closes, press the "+" and "-" buttons at the same time.
The operating directing is reversed.
- Fig. 11
- Fig. 12
- Fig. 13
Copyright © 2018 SOMFY ACTIVITES SA. All rights reserved.
Elixo Smart io