Setting The Gas Grill; Care And Cleaning; Cleaning Agents - Bosch HGA23A1 0S Série Notice D'utilisation

Close the oven door slowly.
7.
Preheat the empty oven for approximately 15 minutes before
8.
baking.
When the dish has finished cooking, turn off the switch for the
9.
lower gas burner.
You can change the temperature at any time.
:
Caution:!
The ignition device should not be actuated for more than 15
seconds. If the burner does not light within 15 seconds, wait for
at least one minute. Then repeat the ignition process.

Setting the gas grill

Open the top cover. The top cover must remain open for as
1.
long as the cooker is in operation.
Turn on the main gas supply to the appliance. Insert the plug
2.
into the socket.
Insert the protecting plate into the groove below the control
3.
panel.
Insert the protecting plate with the longer edge at the front
and the curvature at the bottom.
Secure the protecting plate in the groove below the control
panel using the retainers.
Ensure that the protecting plate is engaged in the retainers. If
the protecting plate cannot be pulled out, it is engaged
correctly. You can now safely use the protecting plate. If it
can be removed, insert it into the groove at a slightly higher
angle and make sure that it engages in the retainers.

Care and cleaning

With attentive care and cleaning, your hob and oven will retain
its looks and remain in good working order for a long time. We
will explain here how you should care for and clean them
correctly.
Notes
Slight differences in the colours on the front of the oven are
■
caused by the use of different materials, such as glass,
plastic and metal.
Shadows on the door panel which look like streaks, are
■
caused by reflections made by the oven light.
Enamel is baked on at very high temperatures. This can
■
cause some slight colour variations. This is normal and does
not affect operation. The edges of thin trays cannot be
completely enamelled. As a result, these edges can be
rough. This will not impair the anti-corrosion protection.
Close the oven door so that it is as close as possible to the
4.
protecting plate.
Push in the function selector and turn it clockwise to the grill
5.
setting .
(
Keep the function selector pressed in and press the ignition
6.
button at the same time.
8
The gas coming from the gas grill is ignited using the ignition
7.
button. Keep the function selector pushed in for 10 seconds
so that the safety pilot starts up.
The flame failure device is activated. If the gas flame goes
out, the gas supply is automatically shut off by the flame
failure device.
Check whether the flame is lit. If the flame goes out, repeat
8.
the process from step 5.
Once the food is cooked, switch off the function selector.
9.
Once the oven has cooled down, remove the protecting
plate.
:
Caution!
The burner knob should not be actuated for longer than 15
seconds in the ignition position. If the burner does not ignite
within 15 seconds, wait at least one minute. Then repeat the
process to light the burner.
Caution!
The gas grill only works when the protecting plate is inserted.
Make sure that the protecting plate is correctly inserted.

Cleaning agents

Damage to the various different surfaces caused by using the
wrong cleaning agent can be avoided by observing the
following instructions.
When cleaning the hob do not use
undiluted washing-up liquid or dishwasher detergent,
■
scouring pads,
■
abrasive cleaning agents such as oven cleaner or stain
■
remover,
high-pressure cleaners or steam jets.
■
Do not clean individual parts in the dishwasher.
■
When cleaning the oven do not use
sharp or abrasive cleaning agents,
■
cleaning agent with a high alcohol content,
■
scouring pads,
■
high-pressure cleaners or steam jets.
■
Do not clean individual parts in the dishwasher.
■
Wash new sponges thoroughly before first use.
35